Setting just preferred-mode in YANG (no allowed-mode leaf-list) built an
invalid mode string with an empty allowed:
Mode 'allowed: ; preferred: 4g' is not supported
The empty allowed: can never match anything in the modem's supported-modes
list, so the user got a cryptic 'is not supported' even when their preferred
mode was, in principle, supported.
When only preferred-mode is configured, walk the modem's supported-modes list
for an entry that already has that preferred, and reuse its allowed set. If
no supported entry has that preferred mode, fail with a message that lists
every combination the modem does support, easier to diagnose than the silent
'empty allowed' case.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Some cellular modems (notably Quectel EM05) don't expose a RESET capability
over MBIM/QMI. Both 'mmcli --reset' and 'mmcli --factory-reset' return
Unsupported immediately, the AT command is never forwarded to the firmware,
and there's nothing modemd can do over the management bus to recover. Until
now modemd's failed-state retry kept calling --reset every 30 s for the rest
of uptime, producing pure log noise:
modemd: <error> [modem0] Resetting after being 30s in state failed
modemd: <info> [modem0] Resetting
ModemManager: <wrn> [modem0] failed requesting modem reset: Unsupported
ModemManager: <wrn> [modem0] failed requesting modem factory reset: Unsupported
modemd: <error> [modem0] Unable to reset
... and the same five lines again 30 s later, indefinitely.
Mitigate this by caching the Unsupported state per modem per session.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Cellular modems (Quectel EM05/EM06/EM12, Sierra EM7565, ...) expose
GPS data as NMEA on a dedicated USB serial interface. Until now we
relied on ModemManager's --location-enable-gps-nmea, which makes MM
hold the NMEA port and parse the stream itself — useful for mmcli
but a dead end for the rest of the system. The result was that
modem GPS was visible only via 'show modem' and could not act as an
NTP fallback time source on devices without dedicated GPS hardware.
This commit reroutes the NMEA stream into the existing
gpsd → chronyd pipeline so cellular modems behave just like any
other NMEA-over-USB GPS dongle. No changes to gpsd, chronyd, or
the ietf-hardware:gps component — the user activates it the same
way as for a dedicated receiver, by adding a 'gps' hardware
component that references /dev/gpsN.
This is Phase 2 of the modem GPS / location integration plan
(.notes/modem-gps-plan.md).
udev (src/modemd/77-mm-modem-gps.rules):
- For known vendor:product:interface tuples, set ID_MM_PORT_IGNORE
so ModemManager keeps off the NMEA port, and add
SYMLINK+="gps%n" so gpsd's existing udev hook picks up the
device automatically.
- Interface-number match uses ENV{ID_USB_INTERFACE_NUM} rather
than ATTRS{bInterfaceNumber}: udev requires all ATTRS{} matches
in a rule to share one parent, but idVendor/idProduct live on
the USB device while bInterfaceNumber lives on the USB
interface. ENV{} matching has no parent constraint and udev
already populates ID_USB_INTERFACE_NUM from bInterfaceNumber.
- Initial entries: Quectel EM05 (2c7c:0125), EM06-E (2c7c:0306),
EM12-G (2c7c:0512), Sierra Wireless EM7565 (1199:9091).
Easy to extend.
modemd (modemd/__init__.py):
- GPS_AT_COMMANDS table maps manufacturer -> (enable, disable) AT
command pair. prepare_location() issues the vendor AT command
via 'mmcli --command=AT+QGPS=1' (or AT+CGPS=1 for Sierra)
instead of --location-enable-gps-{nmea,raw}. Vendor lookup is
substring-based ('Quectel' matches both 'Quectel' and 'Quectel
Incorporated') because ModemManager normalises differently
across firmware revisions. For unrecognised vendors the
high-level MM path is still used as a fallback, so nothing
regresses for hardware not yet in the table.
- The AT path runs based on the udev/vendor table, not on MM's
--location-status capabilities. Setting ID_MM_PORT_IGNORE on
the NMEA port removes 'gps' from MM's capability list even
though the GPS hardware is still there, so a capability gate
would mistakenly skip GPS for the very modems we're targeting.
- _location_capabilities() filters MM-managed sources so a single
unsupported flag (e.g. CDMA on an LTE-only modem) doesn't fail
the whole batched call. Sources the modem doesn't support are
silently skipped; a warning is logged only if the user's YANG
config explicitly lists one.
- Subprocess fan-out collapsed: agps-msa, agps-msb, 3gpp and cdma
flags share a single batched mmcli invocation.
prepare_location() drops from 5 subprocess calls to 1 (unknown
vendor) or 2 (known vendor, AT + batched MM).
- Stringly-typed if/elif source dispatch replaced with a
dict-driven table (LOCATION_MM_FLAGS).
- Two helpers eliminate the ['mmcli', '-m', self.path, ...]
boilerplate at ~30 ModemThread call sites:
self._mmcli(*args, check=True) # runcmd wrapper
self._mmclij(*args) # runcmdj wrapper
build (package/feature-modem/Config.in):
- Select BR2_PACKAGE_MODEM_MANAGER_ATVIADBUS so ModemManager
accepts raw AT commands over D-Bus without being started in
--debug mode. Required by the AT path above; without it
'mmcli --command' is rejected with MM_CORE_ERROR_UNAUTHORIZED.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Cellular modem location data (GPS coordinates, 3GPP cell info) was
previously CLI-only — 'show modem modem0' shelled out to modem-info
which queried mmcli on demand and rendered straight to terminal.
NETCONF/RESTCONF clients had no view into modem location, and there
was no way to tell how stale any modem-state field was.
This commit moves both into the YANG operational tree so they are
accessible through every northbound interface, not just the CLI. It
is Phase 1 of the modem GPS / location integration plan; Phase 2 will
route the modem's NMEA TTY into the existing gpsd → chronyd pipeline
so cellular modems can also serve as an NTP fallback time source.
YANG (infix-hardware.yang, revision 2026-05-10):
- modem-state/last-change (yang:date-and-time): freshness indicator
for the modem-state subtree, bumped on each modemd poll cycle
- modem-state/location-state container: source (gps|3gpp|...),
latitude/longitude/altitude (decimal64 6/6/1 fraction-digits),
cell-id/lac/tac/mcc/mnc, and its own last-change
Runtime path:
- modemd's check_location() now writes
/run/modemd/modemN/location/data.json with the full location data
plus an RFC3339 last-change. Atomic via tmp+rename. Walks the
mmcli output once instead of twice.
- check() touches /run/modemd/modemN/state.json with a fresh
last-change after each successful state poll.
- yanger/infix_modem.py reads both files via HOST.read_json and
folds them into the modem-state operational subtree.
- cli_pretty show_modem_detail rewritten to consume the operational
tree (same path as 'show modem' overview), with new 'Last Update'
lines for both top-level state and location.
- bin/show/modem() consolidated: both 'show modem' and
'show modem REF' use get_json('/ietf-hardware:hardware') — no
more direct modem-info subprocess call.
Cleanup along the way:
- Removed the legacy /run/modemd/modemN/location/{up,down,disabled,
failed} marker file writes — they had no readers anywhere in the
tree. In-memory self.location['state'] is kept purely as the
edge-trigger for the 'Retrieved GPS location' log line.
- Aligned now_rfc3339() output with yanger.common.YangDate (+00:00
form, not Z) so consumers see one consistent yang:date-and-time
format regardless of producer.
- Fixed multi-modem SIM scoping in show_modem_detail: now derives
sim<N> from modem<N> instead of picking the first SIM globally.
The bearer / hardware-revision / phone-number / supported-carrier
sections of 'show modem REF' are deliberately omitted for now —
those fields are not yet in the YANG tree. Bearer details in
particular likely belong on the wwan interface
(ietf-interfaces:interfaces-state) rather than on the modem hardware
component, and can be addressed in a follow-up.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
On SIGHUP, modemd stops all ModemThreads, re-runs sim-setup, then
restarts the modem threads from fresh sysrepo config. The pidfile is
touched with os.utime() once the reload is complete, satisfying Finit's
default pidfile-based notify so confd can signal a reload and wait for
it to finish before proceeding.
This allows operator and APN changes to take effect without a full
daemon restart.
Also extract start_modem_threads() to remove the duplicated thread
startup loop shared between initial startup and reload, and align
sighandler() to use isinstance(th, ModemThread) consistently with the
rest of the thread-management code.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Python scripts without a .py extension are never cached as bytecode by
CPython — every invocation re-parses the source. Packaging as a wheel
pre-compiles all modules to .pyc and installs thin import stubs as the
executables, matching the approach used by bin/show and statd.
Restructure the modemd Python scripts into a proper Python package
(src/modemd/modemd/): each script becomes a module with a main() entry
point. pyproject.toml declares 11 entry points; the Buildroot
MODEMD_BUILD_PYTHON hook builds a wheel via PEP 517, then pyinstaller.py
installs compiled stubs to /usr/libexec/modemd/ and pre-compiled .pyc
modules to site-packages.
/sbin/modemd is now a symlink to the compiled stub.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The initial modem import used a standalone infix-modem YANG module with
an integer-indexed list under /infix-modem:modems carrying a bearer
config mixed in with hardware config. Infix has adopted the ietf-hardware
model to allow for a clearer separation of concerns, this commit aims to
improve on that situation by refactoring the modem model to use the same
architectural pattern already used for WiFi radios, GPS receivers, and
USB ports:
Hardware:
/ietf-hardware:hardware/component[class=infix-hardware:modem]
/ietf-hardware:hardware/component[class=infix-hardware:sim]
Interface:
/ietf-interfaces:interfaces/interface[type=infix-if-type:modem]
Configuration split:
modem component — admin-state (enable/disable), radio access mode,
frequency bands, location services, probe-timeout
sim component — PIN, PUK, carrier profile
wwan interface — APN, IP type, roaming, route-preference, auth
This also enables the modem to appear in 'show hardware' alongside
other hardware components, and to be managed over NETCONF/RESTCONF
using the same ietf-hardware RPCs used for USB and WiFi.
YANG changes:
- infix-modem.yang removed (1089 lines, standalone module)
- infix-hardware.yang: new modem and sim containers, modem-state and
sim-state operational state, typedefs for bands/modes/location,
notification status-update; actions restart/reset/send-sms are
augmented directly on the component list entry (not inside container
modem) to work around sysrepo NP-container parent validation — when
checking a nested action's parent, sysrepo restricts its operational
data fetch to the container path, excluding the sibling 'class' leaf
needed to evaluate the container's 'when' condition, so the container
is never instantiated and the parent check fails
- infix-if-modem.yang: new submodule (same pattern as wifi/wireguard)
adds the wwan bearer container to ietf-interfaces
- infix-if-type.yang: new modem identity for wwan interface type
- confd version bumped to 1.9
confd:
- if-modem.c: new file replaces the stub modem_gen() in modem.c;
generates dagger init scripts with probe-timeout wait loop and
unconditional dummy wwan creation so downstream IP config succeeds
when a USB modem is slow to enumerate at boot
- hardware.c: start/stop/enable/disable modemd (and modem-manager)
in response to admin-state changes on the modem hardware component;
use finit_enable/disable consistently
- hardware_cand_infer_class(): auto-set class for modemN/simN names
- modem.c: stripped to RPC/notification forwarding only; the old
genconf() / enable() / disable() logic is gone — hardware.c owns
the lifecycle now
- interfaces.c: remove wwan from wait-interface timeout (the modem
interface appearance is managed by modemd, not confd's init scripts)
- migrate/1.9: script fully migrates /infix-modem:modems to the new
split model; each modem[N] becomes a modemN hardware component and
simN sim component; each bearer becomes a wwanN interface (bearers
numbered globally across modems); APN, IP type, roaming, preferred-
mode, bands, location, PIN/PUK/carrier are all carried over; plain-
text bearer credentials are moved to a named keystore symmetric-key
(base64-encoded) referenced from bearer/authentication/password;
apn-type, firewall-enabled, dns-enabled and default-route are
dropped (no equivalent in the new model)
modemd:
- load_config() replaces the infix-modem sysrepocfg call; reads from
ietf-hardware (modem/sim config), ietf-interfaces (bearer config),
and ietf-keystore (credentials) — three standard modules instead of
one proprietary one; modems absent from sysrepo config but present
in system.json are still started (physical detection wins)
- Default route written to /etc/net.d/<iface>.conf (picked up by
netd/staticd/zebra) instead of a direct 'ip route add'; routes are
now visible to FRR for redistribution and metric-based failover
- Addresses tagged with proto wwan (rt_addrprotos entry 7) for
precise flush on disconnect without touching other address sources
- _derive_gateway() handles point-to-point bearers where modem
reports gateway as "--"; derives peer from link-scope subnet route
- SimThread exits cleanly on platforms without /dev/simctrl
- sim-setup, modem-info, modem-udev, modem-rpc, modem-sms all ported
to the ietf-hardware/ietf-interfaces namespace
statd:
- infix_modem.py now emits modem-state and sim-state into ietf-hardware
component entries (modem0, sim0, ...) instead of a separate tree;
sim-state reports physical slot, lock state, and SIM operator name
- ietf_hardware.py: hardware component names deduplicated by rename
(cpu → cpu, cpu1, ...) to prevent LY_EVALID when hwmon and thermal
sysfs both normalise to the same sensor name
- show hardware: Cellular Modems and SIM Cards tables added; sensor
table width now adapts to the widest section in the output
- 00-probe: USB modem detection writes to system.json["modem"], same
source as wifi-radios, feeding gen-hardware which emits the
ietf-hardware component entries at factory config generation time
CLI:
- 'show modem [ref]': without ref shows Cellular Modems and SIM Cards
tables (same data subset as 'show hardware'); with ref shows a full
per-modem dump (hardware info, status, cellular, SIM, bearers, GPS)
- 'modem restart <ref>': disconnect and reconnect all bearers without
a full hardware reset
- 'modem reset <ref>': factory-reset the modem firmware
- 'modem sms <ref> <number> <message>': send an SMS via the modem
(uses the signalling plane; no active data bearer required)
- MODEMS PTYPE provides tab-completion reading modem names from
/run/system.json
doc:
- Add initial User Guide for modems
- Update ChangeLog with modem news
- Use absolute URLs in ChangeLog. Relative links only work for in-tree
references, not in release notes
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
defconfig.sh used $# (find result, incl. *~ / *.bak) for the TAP total
but then 'continue'd past backups without decrementing — so a stray
bpi_r4_*_defconfig~ in the tree made TAP see "1..23" followed by only 21
results, and the harness treated the missing 2 as failures. Filter the
patterns at find instead; $# now matches what the loop iterates over
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Three bugs found while testing modem support on hardware:
ietf_system.py: "interface": null written to DNS server entries when
no interface is associated, causing LY_EVALID in the ietf-system
schema validator. Only include the key when the interface name is
non-empty.
ietf_system.py: empty list inserts (user [], server [], options [],
search []) overwrote configured data in the operational store instead
of leaving it intact. Guard each insert so operational data only
shadows configured data when there is something to report.
show system: CPU temperature reported only the first sensor named
exactly "cpu", "soc", or "core". Platforms with multiple thermal
zones (e.g. BPI-R4 exposes cpu and cpu1) always showed only one
reading. Collect all sensors whose name matches a CPU/SoC prefix
and report the maximum.
statd.c: yanger parse errors logged without model name or libyang
error string, making failures hard to diagnose. Include both.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Integrates the modem management subsystem, donated by Avvero Pty Ltd,
adapted to work on any platform without proprietary hardware (simctrl,
modules.json, /sys/class/sim/).
Components:
- package/feature-modem: Buildroot feature package pulling in modemd,
ModemManager, libmbim, libqmi, and USB serial/MBIM/QMI kernel drivers
- package/modemd: Buildroot package for the modemd daemon and helpers
- src/modemd: modem management daemon — detects modems via ModemManager,
connects bearers, configures IP addresses, handles SMS and location
- src/confd/src/modem.c: confd plugin — enables/disables modemd and
modem-manager via sysrepo, forwards RPCs (restart/reset/send-sms)
- src/confd/src/interfaces.{c,h}: IFT_MODEM type for wwan* interfaces;
confd manages address/route assignment, modem daemon owns link state
- src/confd/yang/confd/infix-modem.yang: YANG model for modem config and
operational state (bearers, APN, bands, modes, location, SMS)
- src/statd/python/yanger/infix_modem.py: operational state collector
- patches/modem-manager: upstream patches for udev install path,
multiplexed interface naming, and MBIM port trust from udev hint
(the last fixes Dell DW5811e / Sierra EM7455 on cold boot)
- patches/libqmi: ignore sysfs in download mode
Platform portability fixes for boards without simctrl hardware:
- modem-info: fall back to /run/modems.json when /run/modules.json is
absent; discover wwan interfaces via sysfs scan; provide synthetic SIM
entry when /sys/class/sim/ is not present; fix dbg() to respect flag
- modemd: make --set-allowed-modes=any best-effort (some modems only
support one mode combination and reject any change); skip mode set
when current mode already matches requested mode
- sim-setup: guard simctrl open, return None when modules.json absent
to skip SIM slot switching entirely on non-simctrl hardware
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
In the last major refactor of confd to a stand-alone daemon, new command
line options were added, one of which -v <LEVEL>. Unfortunately opening
up for a few corner cases where the debug flag or the log_level was not
set properly.
This fixes that and also adds a CONFD_ARGS for /etc/default/confd, which
is customary for all daemons.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The M.2 LTE slot uses the USB2 bus. Add it as an unlocked component so
the modem hardware is accessible and visible to users in the config.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
hostapd limit hard what BSSID to use, this since hosatpd is desinged
to use radio-mac+n as default. We demand the user to select the MAC
address, if having multiple BSS.
Material's defaults (Roboto, bluish slate dark mode) looked dull next
to the Chirpy-based kernelkit.org blog. Match its typography and colors
via extra.css, no engine change:
- Lato headings + Source Sans 3 body + system monospace for code
- Dark mode: neutral near-black background, soft-gray text, darker code
blocks, Chirpy blue links (replacing Material's high-contrast slate)
- Light mode: warmer body text, blue links, tinted sidebars
- Keep the orange brand on the masthead; links use Chirpy blue
Set theme.font: false so Material no longer also fetches Roboto.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Extend the existing 'show <running|startup|factory>-config' family with an
optional 'path /XPATH' argument that maps straight to the underlying 'copy
-x' flag, and add 'show operational [path /XPATH]' for symmetry with the
configuration datastores.
admin@example:/> show running-config path /ietf-interfaces:interfaces
admin@example:/> show operational path /ietf-system:system-state
Also, improve error feedback from the copy command slightly.
Before:
admin@example:~$ copy running -x /foo
Error: (null) (5)
Error: failed retrieving running-config data
After:
admin@example:~$ copy running -x /foo
Error: Couldn't parse path "/foo": Prefix "foo" not defined. (5)
Error: failed retrieving running-config data
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
cli-pretty prints a friendly message on stdout before any sys.exit(1)
— 'Interface "w" not found', 'Error, top level "ietf-routing:routing"
missing', etc. The wrapper used subprocess.run(..., check=True) and
on non-zero exit caught CalledProcessError, throwing away the captured
stdout and printing the generic exception message instead.
Drop the check=True / try-except dance, always relay stdout, and only
fall back to the generic 'Error running cli-pretty' line when the
subprocess crashed without producing any output.
Before:
admin@bpi:/> show interface w
Error running cli-pretty: Command '['/usr/libexec/statd/cli-pretty',
'show-interfaces', '-n', 'w']' returned non-zero exit status 1.
After:
admin@bpi:/> show interface w
Interface "w" not found
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The Ethernet packet/RMON counters at the bottom of 'show interface
<name>' were appended with a wider label column than the operational
data above them, breaking visual alignment. Group them under an
"Ethernet Statistics" section heading (Decore.title), same convention
as 'Available Networks' in the wifi scan view.
Narrow the operational-data label column from 20 to 19 chars so the
title bar exactly matches the heading text — a tighter and more
deliberately aligned look. All labels in pr_iface fit within 19
chars except 'lacp system priority' (20); rename it to 'lacp sys
priority' for consistency with the other 'lacp ...' labels (lacp
aggregate id, lacp partner mac, ...) so the new field width works
universally.
Refresh CLI snapshots and doc samples to match.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Fix#1506: restore the VLAN interface documentation that was lost when
networking.md was split into per-topic pages. Content adapted from the
v25.11.0 networking.md VLAN section, plus a new "Stacked (Q-in-Q)"
section showing `eth0.10.20`-style nesting and the layered `show
interface` rendering of the parent chain.
Update the interface-type table in networking.md to point at the new
vlan.md instead of the dangling ethernet.md#vlan-interfaces anchor.
ChangeLog: document the user-facing changes on this branch (YANG model
upgrade, layered show interface output, auto-negotation typo fix) and
the new VLAN documentation.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Update CLI samples across the documentation to the new layered
presentation: physical-medium row when linked (1000baseT/...), bare
MACs, and key: value DATA tokens. Add a short prose block in
ethernet.md and iface.md explaining the layering.
Drop the historical 'show interfaces' (plural) form — removed from
klish years ago — from all user-facing examples and the landing page.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Import ieee802-ethernet-interface@2025-09-10.yang, from IEEE 802.3.2-2025,
and companion ieee802-ethernet-phy-type.yang, replacing the 2019 revision.
Operational interface speed moves to ietf-interfaces:speed, RFC 8343,
eth:speed is now obsolete. Bump infix-interfaces.yang revision to track
the upgrade.
The CLI 'show interface' command renders interfaces as bottom-up layered
protocol rows. Ethernet interfaces a new IEEE link-mode row (1000baseT,
10GbaseLR, ...) is added with 'duplex: full|half' in the DATA column.
Without link the ethernet row is the first row. Tunnels and wifi follow
the same layering: gre/vxlan rows carry remote:/vni: tokens with optional
ethernet sub-row for the L2-bearing variants; wifi rows carry 'station' or
'access-point' ssid:, signal:, stations: tokens.
admin@bpi-76-8f-c2:/> show interface
⚑ INTERFACE PROTOCOL STATE DATA
⇅ lo loopback UP
ipv4 127.0.0.1/8 (static)
ipv6 ::1/128 (static)
⇅ br0 bridge DOWN
│ ethernet 32:2e:3f:76:8f:c2
│ ipv4 192.168.0.1/24 (static)
⇅ ├ lan0 bridge LOWER-DOWN
⇅ ├ lan1 bridge LOWER-DOWN
⇅ ├ lan2 bridge LOWER-DOWN
⇅ └ lan3 bridge LOWER-DOWN
⇅ gre0 gre UP remote: 198.51.100.7
ipv4 10.255.0.1/30 (static)
⇅ sfp1 ethernet DOWN ca:59:f0:77:80:5b
⇅ wan 1000baseT UP duplex: full
ethernet 32:2e:3f:76:8f:c2
ipv4 192.168.0.235/24 (dhcp)
ipv6 fe80::302e:3fff:fe76:8fc2/64 (link-layer)
⇅ wan.10 vlan UP vid: 10
│ ipv4 10.0.10.1/24 (static)
└ wan
⇅ wan.10.20 vlan UP vid: 20
│ ipv4 10.0.10.20/28 (static)
└ wan.10
⇅ wifi0 wifi UP station ssid: corp-net signal: good
ethernet dc:a6:32:00:11:22
ipv4 192.168.7.42/24 (dhcp)
yanger populates phy-type and pmd-type from a static ETHTOOL link-mode
identity table keyed on (port, speed, duplex). Both leaves are populated
for unambiguous media (copper, DAC, copper-T); for generic fiber where
the (port, speed, duplex) tuple can map to multiple PMDs (SR vs LR vs
ER, etc.) only the phy-type family identity is emitted — guessing the
PMD would be misleading. cli_pretty prefers pmd-type (specific) and
falls back to phy-type (family) for display.
yanger also emits ietf-interfaces:speed and fixes a long-standing
'auto-negotation' typo (yanger had never matched ethtool's correctly-
spelled JSON field, so operational auto-negotiation always read
'unknown').
Filling the WG's gap on fixed-speed config
------------------------------------------
IEEE Std 802.3.2-2025 obsoleted the eth:speed leaf without providing a
config-true replacement; the standards-correct way to express what
older Infix configurations called 'fixed speed' is to restrict the set
of PMDs auto-negotiation may advertise. Augment auto-negotiation with
two leaf-lists:
auto-negotiation/advertised-pmd-types config-true, leaf-list of pmd-type
ethernet/supported-pmd-types config-false, leaf-list of pmd-type
Pinning a port to a single mode is now expressed as a single-entry
advertised-pmd-types list. The kernel-supported set is exposed as
operational state for diagnosis — SFP/SFP+ cages report the inserted
module's capabilities, narrowing the list to a single PMD when the
optic only supports one mode (as suggested by @wkz in PR review).
When the supported list collapses to a single entry, yanger uses it
to refine the operational pmd-type leaf — more accurate than the
(port, speed, duplex) lookup for fiber.
confd C apply path (src/confd/src/ieee802-ethernet-interface.c)
translates each advertised pmd-type identity to the corresponding
ETHTOOL_LINK_MODE_*_BIT_*, ORs them into a mask, and emits
'ethtool --change <if> autoneg on advertise 0x<mask>'. An empty
list keeps the historical default of advertising every supported
mode. The (legacy) 'auto-negotiation/enable = false' + speed/duplex
branch is removed — it has no model representation any more.
cli_pretty's detail view gains 'advertised' and 'supported' rows
listing the PMDs in each set. A new _pr_label_list() helper unifies
multi-row rendering across these new rows and the pre-existing
ipv4/ipv6 address rows.
The detailed interface view also gains a 'link mode' row carrying the
pmd-type / phy-type-derived label.
Migration of existing startup configurations
--------------------------------------------
Bump confd version 1.8 → 1.9 to trigger the migration on upgrade.
share/migrate/1.9/10-ethernet-advertise.sh translates old configs of
the form
ethernet { auto-negotiation { enable false; } speed S; duplex D; }
into
ethernet { auto-negotiation { advertised-pmd-types [PMD]; } duplex D; }
mapping (S, D) → PMD via a static lookup covering the copper-T speeds
the deprecated speed leaf historically supported (10/100/1000/2.5G/
5G/10G). Interfaces that don't disable auto-negotiation, or that
lack a speed leaf, are passed through untouched.
Closes#530Closes#805
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
bridge -j vlan global show can return VLAN ranges as
{"vlan": 1, "vlanEnd": 3} instead of individual entries.
The vlans dict was only keyed on the start value, causing
port VLANs 2 and 3 to be reported as "Unexpected".
Also fix typo in error message (brpvlans -> brpvlan).
Move the hostname-triggers-dhcp-client logic from dhcp-client.c into
the centralized dep_hostname() dependency tracker. When the hostname
changes, all interfaces with DHCP client configured are now added to
the diff by the core dependency resolver, so dhcp_client_change() picks
them up through its normal diff-based interface iteration.
When keystore keys change, trigger regeneration of wireguard
interfaces that reference them:
- Asymmetric key change: triggers interfaces using it as private-key
- Symmetric key change: triggers interfaces using it as preshared-key
(both at peers bag-level and individual peer-level)
The 'command' leaf is config, with a strict pattern that doesn't allow
'&', quotes or pipes. Yanger was populating it from podman's full,
untruncated container command -- so any container whose entrypoint
uses shell metacharacters (e.g. sh -c "... && ...") failed YANG
validation.
The symptom: every operational read of /infix-containers:containers
returns SR_ERR_INTERNAL, which in turn fails the whole get-data on
the operational datastore. This breaks case/misc/operational_all and
any RESTCONF/NETCONF read that touches containers.
This was introduced in 59028c4 ("Fix #1466: 'show container' shows no
output"), which added the operational, pattern-less 'cmdline' leaf
but left the old 'command' assignment in place. Drop it -- 'cmdline'
already carries the full command line, and 'command' belongs to
running config.
Note: the failure can look intermittent across test runs because
podman storage is persistent. It only triggers once a container with
a bad-pattern command ends up in 'podman ps -a', including stale or
exited leftovers from earlier runs.
Signed-off-by: Richard Alpe <richard@bit42.se>
Was not correct handled before, a few assumptions was made,
but did not work in reality.
* Fix correct channels for WiFi 6E
* Add missing parameters required for 6ghz to work
Summary of Changes:
bfdd:
- cap IPv6 echo reflection to declared length
- account for FP offset in echo length checks
- fix recv errno filter logic in a few places
- tighten SBFD reflector packet sanity checks
- gate IPv6 echo reflection on known sessions
- tighten auth header parsing skeleton
- validate control packet length before session lookup
bgpd:
- Fix memleak when configuring rd
- Validate if NHC BGPID TLV value is non-zero
- Avoid having a dangling pointer after we free NHC attribute
- Check if BGPID NHC TLV exists when IPv6 next-hop is link-local
- Do not allocate NHC TLV with an extra trailer
- migrate timers during peer_xfer_conn to fix stale route cleanup
- honor 'no activate' for dynamic neighbors in peer-group
- Return immediately when dynamic capability action is not valid
- Validate BGP role capability when handling it dynamically
- fix neighbor IP comparison for IPv6 memcmp return values
- Don't mark nexthop as changed if a set next-hop unchanged is applied
- Return BGP_PEER_INTERNAL when first peer's as type is set to auto
- Update peer sort cache when remote-as auto is used and AS number changed
- Check dynamic capability action before validating ENHE capability
- Do not allocate stream if route-refresh capability is not received
- Move rpki strict check to bgp_accept()
- Fix memory leak for nhc attribute if ipv6 is link-local address
- Fix compilation for Debian 11 when printing uint64 values
- Return zero labels if no BOS found and it's not a withdraw label
- Fix signed overflow in hexstr2num()
- Check the length also when parsing ENCAP attr sub-TLVs
- Validate prefixlen before subtracting when parsing labeled unicast NLRI
- Reset the stream to attr_start + attribute_len when WITHDRAWN
- Revalidate locally originated routes against RPKI changes
- Check if prefixlen is not 0 when parsing flowspec stuff
- Prevent len_string going negative when trying to display flowspec entries
- fix import vrf on non existing vrf
- fix no vrf import command
- Free hostname for FQDN capability if the parsing goes wrong
- Validate MP_REACH_NLRI attribute against incorrect next-hop
- Fix dynamic FQDN capability handling
- Check if the remaining length for subtracting TLV length is enough
- Fix the end pointer boundaries for dynamic graceful restart capability
- Add missing returns when parsing enhanced route-refresh
- Return original as-path when reconciling AS versus AS4
- Do not process route-refresh for AFI/SAFI if it's not negotiated
- Check if we are not overusing error_data buffer when unknown cap received
- fix NHT for explicit link-local BGP peers
- improve packet parsing for EVPN and ENCAP/VNC
- Prevent heap use-after-free for tunnel encapsulation attribute
- Return 0 if AS4 capability is malformed
- close dynamic peer socket in ttl error path
- fix logic handling EVPN_FLAG_DEFAULT_GW
- avoid early return in MPLSVPN NLRI processing
- remove unneeded asserts in packet reads
eigrpd:
- fix byte order in Hello TLV decode functions
- Handling for malformed update packets
- enforce minimum TLV length in Hello handler
- reject invalid prefix mask len
- skip unknown and ignored TLVs
- Improve packet validation
isisd:
- Reject SRv6 Locator TLV with Loc-Size of zero
- consume leftover bytes after FAD sub-sub-TLV loop
- use correct min size values for srv6 subtlvs
- improve validation of flex-algo decoder
- Fix missing neighbor address Sub-TLVs after link-params change
- add unit test for remove_excess_adjs() memory leak fix
- fix memory leak in remove_excess_adjs()
- fix edge condition in max_lsp_count computation
ldpd:
- improve tlv validation in several places
lib:
- Report IPv6 MTU and not IPv4 for if_update_state_mtu6
- disable warning in zlog.c to match master
nhrpd:
- stop debugging auth credentials
- fix byte-order when comparing error code in shortcut path
- guard against zbuf_pulln NULL on truncated packets
- require auth for all received packet types
- harden debug packet parsing against malformed input
- validate AFI index in extension replies
ospf6d:
- move log call out of priv block
- remove asserts in packet-handling paths
- fix issues in ospf6 auth trailer code
ospfd:
- add LSA validation in the apiserver path
- add validation in several places before accessing
pceplib:
- validate during of_list TLV decoding
pimd:
- fix NOCACHE MFC resync detection log, add vrf name too
- use upstream-owned pim pointer in register and upstream timers
- use upstream-owned pim pointer in MSDP update paths
- avoid JP build deref through channel OIL
- guard RP RPF-failure mroute delete on detached OIL
- avoid null deref in upstream delete debug path
- guard channel OIL detach against stale pointers
- fix crash due to double free
- Ensure igmp message is of proper size
- Reject pim packets with a malformed header length
- Fix out of bounds read in AutoRP code
- igmpv3 never checks packet length and trusts the num-sources field
- Do not allow a register-stop message if not received from the RP
- Prevent received msg length from being larger than buffer
- Remove unnecessary asserts
- When receiving a register stop ensure we have enough data to read
- Ensure a register packet has enough space to read S,G data
- Ensure that header has space on packet
ripngd:
- fix data handling in several places
tests:
- Check if route-map with set nexthop unchanged does not prevent outgoing
- Check if mixed peer-group remote-as types can be used with auto
- Verify neighbor addr Sub-TLVs after link-params reset
- Expect return code being 0, not -1 when AS4 is empty or ASN is 0
vrrpd:
- replace some asserts
- only support ethernet in GARP code
- limit advertised timers to 12-bits
Signed-off-by: Mattias Walström <lazzer@gmail.com>
Backport two fixes addressing a critical failure reported by a customer:
an unclean dbus-daemon exit leaves a lingering /run/messagebus.pid, the
daemon then refuse to start, and Finit's restart loop gives up.
0001 service: clean stale pidfile after unclean daemon exit
Drop a daemon-owned (pid:!) pidfile when it still names the
just-reaped PID and that PID is no longer alive.
0002 service: log signal name and core dumps in death message
"by signal: 9" -> "killed by SIGKILL", with ", core dumped"
when applicable. Stronger breadcrumb for sudden deaths.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The \r-overwrite of an in-progress line breaks when something else
writes to stderr between conout(3) and the final call, leaving blank
"[ OK ]" lines. Cache the description and reprint it whole, so the
final status line is robust to intervening output.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
When an interface has been handed off to a container it lives in
another netns, so `ip neigh/addr flush dev FOO` fails on the host.
The failure aborts dagger, and since interfaces_change() runs before
containers_change() in change_cb(), the container delete path is
never reached -- the stale container keeps the interface trapped in
its netns, breaking the next reconfiguration.
Guard both the neighbor and address flush exit scripts with
`if_nametoindex(ifname)` -- true exactly when the interface is in
the host netns, false for both "in a container" and "already gone".
This replaces the pre-existing `!cni_find(ifname) && if_nametoindex(
ifname)` guard at the addr site: cni_find() added no information
for this check and would popen(container find) for nothing when the
interface had been deleted entirely.
Also harden wrap() in /usr/sbin/container so a stale setup pidfile
doesn't short-circuit Finit's stop attempt -- kill the setup PID and
still ask podman to stop the container.
Fixes#1493
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The regression tests do not pass for some reason, could be faulty test
runner (Lifeboat) -- container and DHCP tests failing since Apr 30), so
tests are disabled until the runner is fixed.
[skip ci]
Issue #1392
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Without INFIX_RELEASE, make test resolves INFIX_ARTIFACT to the
unversioned infix-x86_64, but release builds produce versioned
artifacts (infix-x86_64-v26.04.0-rc1.qcow2 etc.), causing the
test environment to fail with "No such file or directory".
[skip ci]
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add an x86_64 regression test job to release.yml that runs after the
build and gates publishing — the release job now requires both build
and test to succeed.
Update test.yml's artifact restore step to use a glob so it handles
both the unversioned CI artifact name (infix-x86_64.tar.gz) and the
versioned release artifact name (infix-x86_64-26.04.0.tar.gz).
Fixes#1392
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add support for static ARP (IPv4) and neighbor cache (IPv6) entries per
interface. Static entries are installed as permanent kernel neighbor
table entries that are never evicted by normal ARP/NDP aging.
Fixes#819
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The mt7622 soc has a built-in wmac, same driver as the mt7615, but
it lacked MODULE_DEVICE_TABLE() so udev could not autoload driver
and firmware.
This commit also adds the wmac+bluetooth specific firmware.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The U-Boot env file is generated by
mkenvimage, which prefixes the variable data with a 4-byte CRC32 by default.
ixpreboot.sh previously imported it with `env import -b` as per uboot docs(-b assume binary format (’0’ separated, “00” terminated).),
which treats the buffer as raw binary and does not strip the CRC.
As a result the first variable's name is parsed a part of CRC.
Later variables import correctly because by then the parser is past the CRC.
Switching to `env import -c` as per uboot docs (-c assume checksum protected environment format.)
makes U-Boot validate and strip the CRC before parsing, so the first variable imports under its real name.
Tested on:
- QEMU
Signed-off-by: Ejub Sabic <ejub1946@outlook.com>
On multi-chip DSA hardware (e.g., boards with multiple mv88e6xxx
chips), each switch chip has its own independent PHC device. With
boundary_clock_jbod enabled, ptp4l starts but only disciplines the
active slave port's PHC — the others drift.
Automatically start phc2sys -a alongside any BC or TC instance using
hardware timestamping. It subscribes to ptp4l's UDS socket, tracks
BMCA, and disciplines all non-active PHCs to match the active one.
On single-chip hardware it is a harmless no-op.
CLOCK_REALTIME is intentionally left untouched. Syncing the system
clock to PTP (phc2sys -rr), feeding the PHC from GPS/NTP (ts2phc,
phc2sys reverse), and full multi-source coordination (timemaster) are
planned as follow-on phases; see the issue tracker for the roadmap.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
NOTE: this is intended only for use on devboards like EspressoBin where
the onboard bootloader only understands fat and ext2 file systems.
To enable, use 'make apply-ext4'
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Inverted values for eMMC and SPI NAND. Also use ABCD instead of
Position as column name to match board markings.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- Add a board README to explain how to get Infix running
- Update mkimage.sh to allow creating images without boot loader
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
A container's command line, as reported by podman, may comtain environment
variables, which the current regexp (added in ed4fe58) does not support.
Extend the regexp to allow environment variables and add an operational,
config false, 'cmdline' leaf node to allow any characters to be reported
for the full command line in the operational output.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Also, simplify board README a bit now that we know that you don't need
to flip the boot switch to program eMMC.
[skip ci]
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Missing BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y caused Buildroot to default
to legacy Makefile build system, which requires BR2_TARGET_UBOOT_BOARDNAME
instead of BR2_TARGET_UBOOT_BOARD_DEFCONFIG, resulting in a build error.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add missing *.hash files for all board packages using the ix-board macro;
they declare LICENSE_FILES = LICENSE but had no hash file, producing a
warning during make legal-info.
Fix the date-cpp package where the hash file was named date.hash instead
of date-cpp.hash (package name is derived from the directory, not the mk
filename), causing Buildroot to skip the hash check entirely.
Add hash files for local-site packages confd-test-mode, netd, and
onieprom that declared LICENSE_FILES but provided no hash.
Also, rename package/date-cpp/date.mk to date-cpp.mk. Buildroot derives
the package name from the directory name, so the mk file must match. To
handle the archive name different we set DATE_CPP_SOURCE.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add board support for the BananaPi BPI-R4 router board, based on the
MediaTek MT7988A (Filogic 880) SoC with quad-core Cortex-A73 CPU.
The BPI-R4 is the successor to the BPI-R3 but uses entirely different
silicon: the internal switch runs at 2.5 GbE per port, the two SFP+
uplinks use native USXGMII at up to 10 Gbps, and WiFi is provided by
a MediaTek MT7996E PCIe module supporting tri-band WiFi 7 (2.4/5/6 GHz).
Two board variants, BPI-R4-2g5 and BPI-R4P, replace one SFP+ cage with
a 2.5 GbE RJ45 port (using the MT7988A internal 2.5G PHY); the R4P adds
an optional PoE daughterboard on that port. Both use the upstream
mt7988a-bananapi-bpi-r4-2g5 device tree.
Interfaces:
- Standard R4: eth1 (gmac1/sfp2 LAN cage) → sfp2, eth2 (gmac2/sfp1 WAN cage) → sfp1
- R4-2g5/R4P: eth1 (2.5G PHY) → wan, eth2 (gmac2/sfp1 WAN cage) → sfp1
Factory reset / WPS button (GPIO14, active-low): detected by U-Boot at
boot for factory reset; reused by Linux as KEY_WPS_BUTTON at runtime.
eMMC install note: the MT7988A eMMC (pins 38-49) and SD card (pins 32-37)
use separate physical pads so there is no electrical bus sharing, unlike
some BPi-R3 configurations. However, a single MMC controller
(mmc@11230000) handles both, so only one is active per boot session.
The eMMC install procedure therefore still requires an intermediate SPI
NAND bootloader step until a Linux-side install path is tested.
SD card build (bpi_r4_sd_boot_defconfig) now uses the new
mt7988a_bpir4_sd U-Boot defconfig with cap-sd-highspeed enabled,
giving 50 MHz SD transfers instead of the previous 25 MHz legacy mode.
Also adds MT7988/MT7996 firmware support to the buildroot linux-firmware
package, for 2.5 GbE port PHY and WiFi7 extension board, and updates the
aarch64_defconfig, aarch64_minimal_defconfig, the arch README, CI
boot/image workflows, mkimage.sh, and the ChangeLog.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This fix the instability of the display on soft reboots,
previous it required a powercycle to get display to work properly
Add patches from rpi-linux, and a small fixup from me.
Signed-off-by: Mattias Walström <lazzer@gmail.com>
Issue #1461 turned out to just be a flaky test, the change in this
commit only bumps the release date.
[skip ci]
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add several entries that were missing from the original release notes,
most notably the SBSA watchdog fix for CN913x (Marvell Octeon) platforms
and the BPI-R3 watchdog fix, plus show keystore, ixll scan, show system
temperature, WiFi signal strength inversion fix, and follow command fix.
[skip ci]
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
When a YANG model change breaks existing startup configs, a migration
script must be included or devices in the field may be left unbootable
after upgrade. Add a dedicated section explaining when scripts are
needed, where they live, and how they work.
Fixes#1459
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Unfortunatly the fix was entered in 25.10, but confd was not stepped
up until 25.11, so this should be for 25.10 but now it is for confd
version 1.6 (infix 25.11), as close as we can get.
this is a follwup for commit 7e37fc49a3
confd: prevent IP addresses on bridge ports
Bridge ports should not have IP addresses configured. The IP address
should be configured on the bridge interface itself, not its member ports.
Add YANG must expression to enforce this rule at configuration time.
Fixes#1122
Add a second discovery backend that reads mDNS neighbor data directly
from the sysrepo operational datastore via `copy operational-state -x
/mdns`, selectable with --backend operational.
Add an auto backend (the new default) that tries the operational data
first and falls back to avahi-browse if the `copy` command is
unavailable or mDNS is disabled (visible via "enabled": false in the
JSON). This makes the service work correctly in all configurations
without manual tuning.
Refactor TXT record parsing into parseTxt() and service/host assembly
into buildHosts(), shared by both backends. Extract fetchOpRoot() and
parseOperational() so scanOperational() and scanAuto() share the same
JSON fetch/decode and host-building logic without duplication.
Fix a bug where TXT values containing semicolons were truncated
(parts[9] → strings.Join(parts[9:], ";")), and apply decode() to TXT
values so avahi \DDD escapes are resolved. Add Apple device model
support via the am= (RAOP/AirPlay 1) and model= (AirPlay 2) TXT keys.
Display the last-updated timestamp in 24-hour format regardless of the
browser's locale.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add reliable avahi client reconnect via explicit free+recreate, reduced
log verbosity (single 10s warning instead of 3×2s loop). Also, binary
TXT record filtering (UTF-8 + XML validity), and finally add a SIGHUP
handler for on-demand reconnect.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Infix now advertises _workstation._tcp, making devices appear
automatically in Windows Explorer's Network folder (Win 10 1709+).
Lead with this, show .local hostname usage for ping/SSH, and demote
the IPv6 multicast ping caveat to a note.
[skip ci]
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
statd now uses avahi-client for mDNS neighbor tracking, so the
native build needs libavahi-client-dev to satisfy pkg-config.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
has_fix() only checks that fix-mode is set (2d/3d), but altitude and
other fields may not yet be populated in the operational datastore when
gpsd is still processing its first NMEA cycles after boot. Calling
verify_position() immediately after has_fix() passes can therefore race
and fail with:
KeyError: 'altitude'
This manifests reliably on the second GPS receiver (gps1) after reboot,
because it is initialized slightly later than gps0 and hits the window
where fix-mode is set but altitude has not yet appeared.
not ok 11 - Verify gps1 position is near the coordinates
# Traceback (most recent call last):
# File "test/case/hardware/gps_simple/test.py", line 29, in verify_position
# alt = float(state["altitude"])
# ~~~~~^^^^^^^^^^^^
# KeyError: 'altitude'
Add has_position() to infamy/gps.py, which gates on fix-mode AND all
position fields (latitude, longitude, altitude, satellites-used) being
present. Replace the has_fix() polls in both the pre- and post-reboot
verify steps with has_position().
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Replace fragile SSH+jq approach for reading the chassis MAC with a
NETCONF query to ietf-hardware:hardware/component[name='mainboard'],
reading phys-address directly from the YANG model.
Also add until() polling to the chassis MAC and chassis+offset MAC
verification steps, consistent with the reset-to-default steps.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
A service restart triggered by finit during sysrepo callbacks can drop
an in-flight HTTP connection, causing copy("candidate", "running") to
fail with RemoteDisconnected. Add retry logic consistent with the
existing PATCH retry pattern in put_config_dict().
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
test_reset() triggers a config reload which causes services such as
rousette to restart. Wait for the transport to become reachable again
before returning from attach(), preventing subsequent API calls from
racing with a still-restarting backend.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add --log-level command line option to filter out log messages from
lower log levels. Then fix the annoying CzechLight warning message
and useless "NACM config validation" log. Then add audit trail as
we have in netopeer2-server, and finish off by stripping redundant
fields from log message: timestamp, identity, and log level.
Fixes#892
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The setting 'stratumweight 0.0' disables stratum in Chrony source
selection (pure distance-based), making client_stratum_selection
non-deterministic on a LAN. Setting it to 1.0 gives srv1 a 1-second
effective advantage per stratum level, which no realistic distance
fluctuation can overcome.
Also correct the YANG descriptions in infix-system and infix-ntp which
had the semantics backwards — claiming 0.0 "ensures lower stratum is
always preferred" when in fact higher values do that.
Fixes#1361
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
After a successful bootstrap confd writes a sentinel to /run/confd.boot
If Finit restarts confd — whether after a crash or a clean exit — the
sentinel is found and the destructive bootstrap phases are skipped:
- gen-config fork (factory/failure configs already exist)
- wipe_sysrepo_shm() (other daemons, e.g. statd, are live)
- sr_install_factory_config() (datastores are already initialised)
- sr_replace_config(NULL, NULL) (running datastore is consistent)
- bootstrap_config() / load startup-config (not needed; sysrepo has
the right state; plugins resync via SR_EV_ENABLED on re-subscribe)
On restart confd reconnects to sysrepo, re-initialises plugins (which
re-subscribe and receive SR_EV_ENABLED to resync with the live running
datastore), then enters the steady-state event loop.
The sentinel lives on tmpfs so a real reboot always produces a clean
slate. Crash-loop protection is delegated to Finit's max-restarts (10).
As a side-effect this also enables a future "run-once" mode for resource
constrained systems: confd can exit after bootstrap and the sentinel
ensures any later restart just re-attaches without re-bootstrapping.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add a finit_enable/disable/reload() family in core.c that directly
manipulates Finit's service state without fork+exec overhead:
finit_enable(svc) -- create symlink in /etc/finit.d/enabled/
finit_disable(svc) -- remove symlink from /etc/finit.d/enabled/
finit_delete(svc) -- remove both symlink and service entirely
finit_reload(svc) -- utimensat() on .conf to schedule reload
Printf-style variants (finit_enablef/disablef/reloadf) handle
template instance names such as container@foo and hostapd@wlan0.
All systemf("initctl ... enable/disable/touch ...") call sites across
containers, dhcp-server, firewall, hardware, ntp, routing, services,
syslog, and system are converted to the new API.
As a related cleanup in services.c, drop the remaining srx_enabled()
calls in favour of reading the already-fetched config tree directly
via lydx_is_enabled(lydx_get_xpathf(config, ...)), eliminating the
last sysrepo round-trips from that module.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Previously svc_enadis() would call 'initctl enable + touch' for every
config change event, even when the service's enabled state was unchanged.
This caused rousette to be unnecessarily restarted on every test_reset(),
racing with the active RESTCONF connection on slow hardware.
Replace svc_enadis() and svc_change() with svc_enable() which only
manages nginx symlinks and calls 'initctl enable/disable' -- never touch.
Each handler now checks the diff for the specific leaf that changed:
- If /enabled appears in diff: call svc_enable() to start or stop it
- If other config leaves changed with service already enabled: touch only
This ensures rousette, ttyd, netbrowse, avahi, sshd, and lldpd are only
restarted when their configuration actually requires it.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Save a few CPU cycles by skipping a new dagger generation when no
interfaces have been modified/added/deleted.
Uses d->next_fp as the sentinel: NULL means no claim was made for this
transaction. dagger_evolve() and dagger_abandon() now NULL it after
fclose, so subsequent unclaimed transactions also get the clean early
return.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The operator sees Infix through YANG models and should not need to know
which library implements a given feature. Rename the public-facing
parts of the avahi module to use the mdns vocabulary:
- Log strings: "avahi: ..." → "mdns: ..."
- Public API: avahi_ctx_init/exit → mdns_ctx_init/exit
- Main type: struct avahi_ctx → struct mdns_ctx
- statd field: statd.avahi → statd.mdns
Internal types (struct avahi_neighbor, avahi_service, …) and file names
(avahi.c, avahi.h) are kept as-is — developers debugging at the C level
benefit from knowing the underlying implementation.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
When the mdns service is stop-started (e.g. after a config change),
statd's avahi client fires AVAHI_CLIENT_FAILURE momentarily. With
AVAHI_CLIENT_NO_FAIL the client reconnects automatically, but the
immediate ERROR log is misleading:
ERROR: avahi: client failure: Daemon connection failed
New behavior:
- On AVAHI_CLIENT_FAILURE: start a 2 s deferred timer (no immediate log)
- Timer fires up to 3 times (~6 s total); on the 3rd attempt, check if
mDNS is enabled in the running config via a temporary sysrepo session
- Log ERROR only if the daemon is still down AND mDNS is enabled
- On AVAHI_CLIENT_S_RUNNING: cancel the timer, reset the counter, and
log NOTE "mDNS daemon reconnected" if a failure had been seen
This silences the error entirely when the operator has disabled mDNS
(expected), and defers it by ~6 s for a brief restart (self-heals
before the timer fires).
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- Use same log frameworks as reset of confd
- Use existing primitives from libite + libsrx
- Drop remaining pthreads
- Coding style fixes
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Replace logging + logging.handlers with a lightweight syslog wrapper,
and argparse with manual argv parsing. On a sama7g54, this cuts yanger
startup from ~770ms to ~470ms by eliminating ~300ms of stdlib imports.
Also batch external command invocations:
- ietf_routing: two sysctl calls instead of two per interface
- ietf_hardware: one ls per hwmon device instead of six
- bridge: fetch mctl querier data once instead of once per VLAN
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Only install the keys on CHANGE event, fixes this annoying issue:
Nov 5 01:32:10 ix confd[2011]: Installing HTTPS gencert certificate "self-signed"
Nov 5 01:32:10 ix confd[2011]: Installing SSH host key "genkey".
Nov 5 01:32:11 ix confd[2011]: Installing HTTPS gencert certificate "self-signed
Nov 5 01:32:11 ix confd[2011]: Installing SSH host key "genkey".
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Use SR_SUBSCR_NO_THREAD for all subscriptions and integrate sysrepo
event pipes into a libev event loop. This eliminates approximately 30
per-subscription threads, reducing overhead on embedded ARM hardware.
A temporary poll-based "event pump" thread handles callback dispatch
during bootstrap (where sr_replace_config blocks waiting for callbacks),
then exits. After bootstrap, the single-threaded libev loop takes over
for steady-state event processing.
Note, the confd-test-mode plugin still requires use of threads so we do
not create deadlocks when calling sr_replace_config().
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- Add x509-public-key-format identity to crypto-types
- Add certificate node to web services container
- Use certificate from ietf-keystore as web cert
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Neither the Raspberry Pi 2B or the Microchip SAMA7G54-EK board have WiFi
hardware by default so drop WiFi, and GPS, support to allow for smaller
builds with only the bare essentials in kernel and system.
Minimal builds in general don't need WiFi or GPS either, so let's disable
them from all. This may become a central theme going forward, keeping
the minimal builds ... minimal.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
netopeer2 and rousette were starting as soon as confd had a PID, while
confd was still loading the startup config via sr_replace_config(). This
held a write lock on the running datastore. A test calling test/reset
shortly after the NETCONF port opened would have its own sr_replace_config()
block on that lock for up to 60 s, at which point sysrepo timed out the
whole RPC with "SHM event 'rpc' processing timed out".
Fix by adding the usr/bootstrap condition to both management servers so
they don't accept connections until confd signals that bootstrap is complete.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Relocate probe of wifi radios from gen-hardware to 00-probe. This saves
one python invocation and some precious CPU cycles at boot.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Follow-up to 90f619b which first introduced the /etc/hostname.d concept.
This commit moves the setup of /etc/hostname.d to post-build.sh dropping
the initial call to the hostname activation script a bit, since it is
called anyway after bootstrap has finished. The scrip is also given a
bit of a refrehs, reducing overhead and needless log messages.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Allow confd to start even earlier at boot and call 'gen-config' as a
background task, pending on it to complete before we load the sysrepo
factory datastore.
Also, add Finit style progress to console so users can see the phases
of the bootstrap process.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Infix technically does not need to start dbus and dnsmasq before confd
has loaded the system startup-config. So we move it in time to save
some CPU cycles for confd & C:o.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
On single-core Cortex-A7, the YANG bootstrap and config loading is the
dominant boot bottleneck. The current sequence spawns three serial
phases (bootstrap, sysrepo-plugind, load), each performing independent
sr_connect()/sr_disconnect() cycles, and every sysrepoctl/sysrepocfg
invocation is a fork+exec that rebuilds SHM from scratch.
Replace all three with a single confd binary that does one sr_connect()
and performs all datastore operations in-process:
- Wipe stale /dev/shm/sr_* for a clean slate
- sr_install_factory_config() from the generated JSON
- Smart migration: compare config version via libjansson, only
fork+exec the migrate script when versions actually differ
- Load startup-config (or test-config) via lyd_parse_data() +
sr_replace_config(), mirroring what sysrepocfg -I does internally
- On failure: revert to factory-default, load failure-config, set
login banners (Fail Secure mode)
- On first boot: copy factory-default to running, export to file
- dlopen plugins and enter event loop
The bootstrap shell script is split: config generation (gen-hostname,
gen-interfaces, etc.) stays in the new gen-config script, while all
sysrepo operations move into the C daemon. The finit boot sequence
collapses from 5 stanzas to 2 (gen-config -> confd).
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Backport fixes from upstream post v4.16 release. Mainly to fix
mdns-alias crash+restart counter issue when avahi-daemon has to
be restarted. Finit did not properly clear the dependency that
mdns-alias had on avahi-daemon, causing it to crash and have its
restart counter incremented.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The v2025.01 release supports the Microchip SamA7G5* eval kit(s), which
means we can enjoy the same patch level of U-Boot as other Infix boards
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- The biggest changes are syncing with latest BusyBox (busybox-update-config)
- Disable optimize for size
- Enable feature "SH_NOFORK" which allows /bin/sh to call applet_main()
directly without having to fork+exec busybox
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Fixes a regression from 0c11cea where local composite actions
(.github/actions/) were referenced with relative paths. When spins
reuse our reusable workflows, GitHub resolves relative action paths
in the context of the calling repo, not infix — breaking the build.
Replace all uses of ./.github/actions/{cache-restore,podman-cleanup}
with kernelkit/actions/{cache-restore,podman-cleanup}@v1 (new repo).
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Replace ERROR() with ERRNO() in all error paths following POSIX API
calls (fopen, rename, realloc, fmkpath, etc.), removing redundant
manual strerror(errno) formatting where present.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Before netd starts confd might want to create .conf file for it to run,
so we sort of depend on /etc/net.d existing at boot.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Set dhcp-authoritative so clients with unexpired leases are not NAKed
after a router crash or factory reset that clears the lease database.
Drop the untagged suppress directives for options 3 (router) and 6
(dns-server): they conflict with the global options confd writes to
dnsmasq.d/, causing spurious "Ignoring duplicate dhcp-option" warnings.
Per-subnet tagged options already suppress auto-detection, and without
an active dhcp-range there is nothing to suppress anyway.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Ensure we translate the hostname before we generate the udhcpc command
line options, otherwise we'll send '-x hostname:rpi-%m' to udhcpc.
Also update all board specific factory configs with the missing setting
'"value": "auto"' for the DHCP hostname option. This to match what we
already do when we infer options when enabling a DHCP client in the CLI.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Two races could prevent DHCP-learned default routes from being installed
at boot:
1. The signal from the DHCP client script could be lost leaving conf.d
updated but frr.conf stale.
2. Even when the signal was received, 'vtysh -b' could fail because the
FRR daemon chain (mgmtd→zebra→staticd) writes PID files before being
fully operational, causing netd to give up with no retry.
Fix both by refactoring netd to use libev:
- Use an inotify watch of CONF_DIR, so netd reacts directly to file
changes without depending on signal delivery.
- On backend_apply() failure, schedule a retry in 5s and call pidfile()
unconditionally so dependent services are not blocked waiting for the
Finit condition 'pid/netd' to be satisfied.
We also take this opportunity to rename /etc/netd/conf.d/ to /etc/net.d/
The extra /etc/netd/ directory level served no purpose — nothing else
lives there. Flatten to /etc/net.d/ which reads more naturally as the
drop-in directory for network configuration snippets.
Also, reduce logging a bit since each netd backend already logs success
or fail which is sufficient to know that a configuration change has been
applied or not.
Finally, with the new inotify processing in netd it's redundant to call
'initctl reload netd' from the udhcpc script, in fact it will only cause
unnecessary overhead, so we drop it.
Fixes#1438
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add a must expression to ensure users do not set static neighbors when
the interface type is not point-to-multipoint or non-broadcast.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add board support for the BananaPi BPi-R64 router board, based on the
MediaTek MT7622 SoC and MT7531 Gigabit Ethernet switch.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
In a hybrid MBR the conventional layout (used by gdisk and others) is:
MBR[0] = 0xEE (GPT protective, covers whole disk)
MBR[1..3] = user-selected GPT partitions with legacy type codes
genimage currently appends the 0xEE entry after the data partitions,
producing the opposite order. This is fine for most platforms, but
breaks firmware that detects GPT by inspecting only MBR entry 0: seeing
a non-0xEE type there it falls into pure-MBR mode and cannot look up
GPT partitions by name.
The TF-A partition driver (drivers/partition/partition.c) exhibits
exactly this behaviour: load_mbr_header() copies entry[0] and checks
type == 0xEE to select between MBR and GPT mode. The MediaTek MT7622
platform (BananaPi BPI-R64) is a concrete example where this matters.
On the other hand, Raspberry Pi firmware scans all MBR slots for a
bootable FAT32 partition. If slot 0 holds a 0xEE protective entry the
firmware switches to GPT detection, looks for an EFI System Partition
UUID, and reports "no bootable partitions" when none is found.
Add an opt-in hdimage option `gpt-protective-first = true` that places
the 0xEE entry at slot 0 and shifts data partitions to slots 1..3.
The default (false) preserves the existing genimage behaviour so that
platforms like Raspberry Pi continue to work without any changes.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The Raspberry Pi 400 shares hardware with the RPi 4B but differs in one
important way: it has an internal keyboard and mouse connected through a
VIA Labs USB hub on the VL805 xHCI controller. Break the symlink to
raspberrypi,4-model-b and maintain a dedicated product directory.
Factory config changes from the 4B default:
- USB1/USB2/USB3 all unlocked: USB2 carries the internal keyboard hub
and USB3 the superspeed companion; all are unlocked as this is a
desktop device
- DHCP vendor-class corrected to "Raspberry Pi 400"
Also add interface-quirks.json for the eth0 PHY detach behaviour and
the smsc95xx broken flow-control quirk (inherited from the 4B config
but now explicit), and remove the spurious bootable flag from the
primary and secondary rootfs partitions in genimage.cfg.in.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Remove console=map:0 from the [pi4] section which was suppressing HDMI
output and disabling the display getty. Making it really difficult to
use it as a regular console.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Two related problems prevented devices behind an intermediate hub (e.g.
the VIA Labs hub on the RPi 400's VL805 xHCI) from being authorized
when confd unlocks a USB bus:
1. Cascade ordering: usb_authorize() ran nftw() with FTW_DEPTH, which
visits children before the root-hub entry. The hub was authorized
while authorized_default was still 2, so when the kernel probed the
hub's children it immediately denied them. Fix: write
authorized_default=1 on the bus before entering nftw.
2. Slow/async probe: hub port enumeration is asynchronous — devices
behind a hub may appear in sysfs after nftw has already finished.
Fix: add a udev rule that catches usb_device add events on buses
where authorized_default=1 is already set on any ancestor root hub
and authorizes them immediately.
The ATTRS{} matcher in udev walks the full sysfs parent chain, so
authorized_default=1 on the root hub is visible even for devices several
hubs deep. Buses still locked at authorized_default=0 are left alone.
Also expand the docstring in generic_usb_ports() to document the
design: each root hub gets its own uniquely-named entry (USB, or USB1/
USB2/... when multiple) so buses can be individually controlled, and
boards needing finer control should use DT usb-ports annotations.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Replace the costly read-only filter loop (awk+tr per line) with a
stderr redirect, use /sys/class/net/ instead of ip+jq, and batch
all sysctl writes into a single call.
Reduces boot time by ~4s on 32-bit Arm systems.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Calling tune2fs for ext4 partitions at boot costs more than one second
boot time on 32-bit Arm systems, with very little gain. Dropping this
restores the default periodic fsck *and* saves boot time.
Instead of calling sgdisk four times, call it only when resizing and
instead use sysfs to find named paritions. Saves seconds on boards
with weaker CPU and slow media.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The MVEBU SafeXcel Crypto Engine firmware (linux-firmware minifw) was
originally added in 70c12c3 to the generic aarch64 defconfigs to silence
kernel probe failures on Marvell Armada SoCs (37xx, 7k, 8k, CN913x):
crypto-safexcel f2800000.crypto: Firmware load failed.
crypto-safexcel f2800000.crypto: HW init failed (-2)
It was then accidentally dropped in 0e2d12e (kernel upgrade to 6.18),
which rebased on a tree that predated the firmware addition.
Rather than restoring it to the generic defconfigs, move it to the two
Marvell board Config.in files where it actually belongs — consistent
with how RTL8169 firmware was handled for the Raspberry Pi CM4 IoT
Router Board Mini in 68313773.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The awk insertion path used getline to peek at the line right after the
"### Changes", but only printed it when NF == 0 (blank line). If the
section already had a non-blank entry (e.g. a Buildroot upgrade line),
getline consumed it silently and the kernel line was written in its
place.
Fix by adding the missing else branch so the consumed line is always
re-emitted — blank lines before the new entry, non-blank lines after it.
Also demote the missing-UNRELEASED guard from exit 1 to a warning with
return 0, so the workflow doesn't abort when a new release cycle hasn't
had its ChangeLog section opened yet.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add three SSH-related commands to the operational CLI:
ssh [user <name>] [port <num>] <host>
Connect to a remote device over SSH, running as the
CLI user (not root) by dropping privileges before exec.
set ssh known-hosts <host> <keytype> <pubkey>
Pre-enroll a host public key received out-of-band (e.g.
via email after a factory reset) into ~/.ssh/known_hosts,
avoiding a TOFU prompt on first connect.
no ssh known-hosts <host>
Remove a stale host key entry using ssh-keygen -R, e.g.
after a device factory reset causes a key mismatch.
Tab completion is provided for key types (ssh-ed25519,
ecdsa-sha2-nistp256, etc.) and for known host names/IPs.
A new run_as_user() helper is introduced alongside the existing
run(), factoring out the fork+setuid+execvp pattern used by
infix_shell() so it can be shared across the SSH functions.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
A legacy name length limit in firewalld triggered problems with longer
policy names. This patch to firewalld lifts that limit by checking the
backend in use, no limit for nftables.
Fixes#1389
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Always emit the "1..N" plan line before exiting with error so test
harnesses don't report "test error, no plan" for failed or aborted
tests.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Increase Zebra NETLINK buffer to fix reported issues with zebra being
out of sync with kernel routes and interface changes.
Also, try '-a' option to allow other processes to delete zebra routes.
Other changes in this commit:
- Minor fixes to Finit service files for consistency
- Empty daemon.conf stub files to silence bogus mgmtd errors at startup
- Relocate all skeleton files from board/common to separate from files
that are actual Infix additions and what's package system integration
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
network.local is a discovery/browse page, not a management interface.
Serving it over HTTP eliminates the self-signed certificate warning
browsers show for .local mDNS names without changing the security
posture of the actual device management pages (still HTTPS-only).
The new port-80 server_name block takes precedence over the catch-all
HTTP → HTTPS redirect in default.conf.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
avahi-browse returns 127.0.0.1 (or ::1) when resolving services on the
same machine netbrowse is running on. These addresses are meaningless
for display and misleading as click targets. Skip the entire 127.x/::1
range and link-local (fe80:) when choosing the preferred address for a
host card; the card addr field is simply omitted if no routable address
is seen.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- IP address shown in soft parens on the card header line, e.g.
"infix.local (192.168.1.10)"; IPv4 preferred over IPv6, link-local
skipped
- Product name and OS version (from mDNS TXT records "product=" and
"ov=") shown as a secondary line below the header when available
- Theme toggle icons changed from ◐/●/○ to ◐/☽/☀ (system/dark/light)
- browse.go: introduce Host struct (addr, product, version, other, svcs)
replacing the flat []Service map; scan() now returns map[string]Host
- Search also matches against IP, product, and version fields
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Apple devices (e.g. Apple TV) publish vv=1 in their AirPlay/RAOP TXT
records, causing a false positive with our Infix platform marker.
Tighten the filter to require vv=1 together with at least one management
service type (ssh, https, http, netconf, restconf), which Apple devices
never advertise. Keep on=Infix as a fallback for older firmware that
predates vv=1.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
avahi's parseable output uses \DDD decimal escape sequences, not octal.
The previous decoder treated them as octal, causing digits 8 and 9 to
fall through undecoded (e.g. \058 → ':' and \091 → '[' were shown
literally). Also handle \X non-digit escapes (e.g. \. → '.') used for
dots in service instance names.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add a `hostname` leaf to the `mdns` YANG container with default `"%h"`,
allowing operators to override the avahi host-name used for mDNS A/AAAA
records without reflashing. The default expands to DEFAULT_HOSTNAME from
os-release, preserving existing behaviour for unconfigured deployments.
Format specifiers %h/%i/%m are supported via the existing hostnamefmt()
infrastructure, which is also fixed to copy the const fmt argument to a
local buffer before modification (UB when called with a libyang-owned
string).
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Use avahi's %h wildcard in service names so each device's hostname is
included, avoiding collision suffixes (#2, #3) when multiple Infix
devices are on the same network.
Skip TXT records whose JSON value is null rather than emitting empty
key= fields. Add _workstation._tcp (with chassis MAC) and
_device-info._tcp (with model= from product-name) as always-on records
tied to mDNS being active.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Simplify and consolidate generation of mdns service records from an
external script to C. This reduces fork + exec and saves two seconds
of boot time on single core Cortex-A7 systems.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Instead of publishing A/AAAA records for $(hostname).loocal with a CNAME
infix.local, we flip it around to take advantage of the mDNS conflict
resolution rules. This gives us infix.local for one device ont the LAN
and infix-2.local for the next.
Update all service records to *not* advertise hostname, but instead to
let Avahi imply that from the advertised A/AAAA and CNAME records.
Fixes#1387
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Introduce libfleet.sh and a new 'fleet' subcommand to ixll for managing
and operating enrolled Infix devices via RESTCONF.
Device configuration is stored in ~/.config/infix/config.json
(chmod 600): and organised by profile, allowing bulk operations across
groups of devices (e.g. all aarch64 targets).
New commands:
ixll fleet enroll [-d] [-p profile] [-u user] [-w password] <name> <address>
ixll fleet list
ixll fleet upgrade <name|profile> <url>
ixll fleet backup [-o dir] <name|profile>
ixll fleet reboot <name|profile>
Upgrade runs in parallel across a fleet and shows a live per-device
progress bar by polling the infix-system:install-bundle RPC and the
installer state from the YANG operational data store.
The global -A flag (admin/admin) is honoured as a credential fallback
for devices enrolled without an explicit password.
Also fix a pre-existing typo: ">2" → ">&2" in the error path.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This patch adds support for chronyd's stratumpweight both in the NTP
client (ietf-system) and client+server (ietf-ntp) should fix the flaky
NTP stratum test.
Also, make sure to *not* 'rm -rf /etc/chrony/conf.d/*' in system.c to
prevent clobbering settings potentially made in ntp.c
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This is a follow-up to c559b8f2 (new-frr) where netd now is responsible
for funneling static routes, as well as routes from DHCP clients, into
the kernel via Frr.
For this to work, in particular at boot, any DHCP client must wait for
netd to have started or any default routes learned will be lost.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
DNS does not allow CNAME records at an apex domain (e.g. kernelkit.org),
so GitHub Pages cannot reliably redirect kernelkit.github.io to it. A
www subdomain can carry a CNAME pointing directly to kernelkit.github.io,
giving GitHub full control over the mapping and making the redirect work.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The weird `if env | grep -q 'reset-volumes'` construct is due to Klish
not sanitizing names before constructing variables, which leads to env
variables with '-' in them, not allowed in POSIX sh.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
Joachim Wiberg
