mirror of
https://github.com/kernelkit/infix.git
synced 2026-07-22 01:13:00 +02:00
Joachim Wiberg
f78f161dbe
The initial modem import used a standalone infix-modem YANG module with
an integer-indexed list under /infix-modem:modems carrying a bearer
config mixed in with hardware config. Infix has adopted the ietf-hardware
model to allow for a clearer separation of concerns, this commit aims to
improve on that situation by refactoring the modem model to use the same
architectural pattern already used for WiFi radios, GPS receivers, and
USB ports:
Hardware:
/ietf-hardware:hardware/component[class=infix-hardware:modem]
/ietf-hardware:hardware/component[class=infix-hardware:sim]
Interface:
/ietf-interfaces:interfaces/interface[type=infix-if-type:modem]
Configuration split:
modem component — admin-state (enable/disable), radio access mode,
frequency bands, location services, probe-timeout
sim component — PIN, PUK, carrier profile
wwan interface — APN, IP type, roaming, route-preference, auth
This also enables the modem to appear in 'show hardware' alongside
other hardware components, and to be managed over NETCONF/RESTCONF
using the same ietf-hardware RPCs used for USB and WiFi.
YANG changes:
- infix-modem.yang removed (1089 lines, standalone module)
- infix-hardware.yang: new modem and sim containers, modem-state and
sim-state operational state, typedefs for bands/modes/location,
notification status-update; actions restart/reset/send-sms are
augmented directly on the component list entry (not inside container
modem) to work around sysrepo NP-container parent validation — when
checking a nested action's parent, sysrepo restricts its operational
data fetch to the container path, excluding the sibling 'class' leaf
needed to evaluate the container's 'when' condition, so the container
is never instantiated and the parent check fails
- infix-if-modem.yang: new submodule (same pattern as wifi/wireguard)
adds the wwan bearer container to ietf-interfaces
- infix-if-type.yang: new modem identity for wwan interface type
- confd version bumped to 1.9
confd:
- if-modem.c: new file replaces the stub modem_gen() in modem.c;
generates dagger init scripts with probe-timeout wait loop and
unconditional dummy wwan creation so downstream IP config succeeds
when a USB modem is slow to enumerate at boot
- hardware.c: start/stop/enable/disable modemd (and modem-manager)
in response to admin-state changes on the modem hardware component;
use finit_enable/disable consistently
- hardware_cand_infer_class(): auto-set class for modemN/simN names
- modem.c: stripped to RPC/notification forwarding only; the old
genconf() / enable() / disable() logic is gone — hardware.c owns
the lifecycle now
- interfaces.c: remove wwan from wait-interface timeout (the modem
interface appearance is managed by modemd, not confd's init scripts)
- migrate/1.9: script fully migrates /infix-modem:modems to the new
split model; each modem[N] becomes a modemN hardware component and
simN sim component; each bearer becomes a wwanN interface (bearers
numbered globally across modems); APN, IP type, roaming, preferred-
mode, bands, location, PIN/PUK/carrier are all carried over; plain-
text bearer credentials are moved to a named keystore symmetric-key
(base64-encoded) referenced from bearer/authentication/password;
apn-type, firewall-enabled, dns-enabled and default-route are
dropped (no equivalent in the new model)
modemd:
- load_config() replaces the infix-modem sysrepocfg call; reads from
ietf-hardware (modem/sim config), ietf-interfaces (bearer config),
and ietf-keystore (credentials) — three standard modules instead of
one proprietary one; modems absent from sysrepo config but present
in system.json are still started (physical detection wins)
- Default route written to /etc/net.d/<iface>.conf (picked up by
netd/staticd/zebra) instead of a direct 'ip route add'; routes are
now visible to FRR for redistribution and metric-based failover
- Addresses tagged with proto wwan (rt_addrprotos entry 7) for
precise flush on disconnect without touching other address sources
- _derive_gateway() handles point-to-point bearers where modem
reports gateway as "--"; derives peer from link-scope subnet route
- SimThread exits cleanly on platforms without /dev/simctrl
- sim-setup, modem-info, modem-udev, modem-rpc, modem-sms all ported
to the ietf-hardware/ietf-interfaces namespace
statd:
- infix_modem.py now emits modem-state and sim-state into ietf-hardware
component entries (modem0, sim0, ...) instead of a separate tree;
sim-state reports physical slot, lock state, and SIM operator name
- ietf_hardware.py: hardware component names deduplicated by rename
(cpu → cpu, cpu1, ...) to prevent LY_EVALID when hwmon and thermal
sysfs both normalise to the same sensor name
- show hardware: Cellular Modems and SIM Cards tables added; sensor
table width now adapts to the widest section in the output
- 00-probe: USB modem detection writes to system.json["modem"], same
source as wifi-radios, feeding gen-hardware which emits the
ietf-hardware component entries at factory config generation time
CLI:
- 'show modem [ref]': without ref shows Cellular Modems and SIM Cards
tables (same data subset as 'show hardware'); with ref shows a full
per-modem dump (hardware info, status, cellular, SIM, bearers, GPS)
- 'modem restart <ref>': disconnect and reconnect all bearers without
a full hardware reset
- 'modem reset <ref>': factory-reset the modem firmware
- 'modem sms <ref> <number> <message>': send an SMS via the modem
(uses the signalling plane; no active data bearer required)
- MODEMS PTYPE provides tab-completion reading modem names from
/run/system.json
doc:
- Add initial User Guide for modems
- Update ChangeLog with modem news
- Use absolute URLs in ChangeLog. Relative links only work for in-tree
references, not in release notes
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
1.7 KiB
1.7 KiB
Welcome to Infix, your immutable, friendly, and secure operating system! On these pages you can find both user and developer documentation.
Most topics on configuring the system include CLI examples, but every setting, as well as status read-back from the operational datastore, is also possible to perform using NETCONF or RESTCONF. In fact, the Infix regression test system solely relies on NETCONF and RESTCONF.
Tip
The CLI documentation is also available from inside the CLI itself using the
helpcommand in admin-exec mode.
- CLI Topics
- Infix User Guide
- Infix In-Depth
- Developer Topics