- Backport fix to allow raw kernel logs to console
- Save 10 rotated (and gzipped) backups of all logs
The latter change was discussed a few weeks ago. We determined it was a
safe number since all active products have eMMC with *lots* of storage.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Only the first listed console in /sys/class/tty/console/active starts
properly, the remaining one(s) were registered using the wrong :ID and
no arguments to getty.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Even when `managed = "in-band-status";` was specified on a port,
mv88e6xxx would insist on forcing the values that were supposed to be
automatically picked up by the MAC via in-band signaling.
In the case of USXGMII links on 6393X, forcing the link bit would
sometimes, for reasons that are not understood, cause the SERDES to
reset its USXGMII link partner base page (register 4.0xf0a2) to 0,
which it would then interpret as 10M/half-duplex. As a result, the
SERDES would erroneously perform rate-matching to 10M on egress
towards the PHY (which is configured for 10G/full-duplex), leading to
nothing but dropped packets and much sadness.
This can most easily be reproduced by the following setup:
.------------.
| .-----. .-------.
| | p9 +---+ 3310P +--.
| 6393X :-----: :-------: | T- or X-Units looped via external cable
| | p10 +---+ 3310P +--'
| '-----' '-------'
'------------'
Make sure that neither p9 nor p10 are managed using in-band-status.
1. ip link set dev p9 up; ip link set dev p10 up
2. ip link set dev p9 down
3. ip link set dev p9 up
After step (3), p10 will experience the failure described above in
about 3/4 of the cases. In the cases where the issue does not arise,
simply repeat steps (2) and (3).
Actually a part of statd, but had to make
a separarate package to get it to work.
Statd helper-scripts are now pre-compiled instead of doing it
in runtime.
Fixes#379
The Finit @console construct detects what your actual serial console is
by looking it up in /sys/class/tty/console/active. This to avoid any
weird problems that might occur when using /dev/console.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Even though dnsmasq only listened to requests from 127.0.0.1, port 53
was visible using nmap. We only use dnsmasq as a local resolver, so
we can safely change the config to bind to loopback instead, and at
the same time get less noise from nmap scans.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This commit adds a landing page, generated from the top README.md. It
is a temporary fix before adding a proper web ui.
Run ./gen.sh from the directory to update index.html using the template.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Refactor mDNS service record generation for improved control of
announcing services. All to add support for modifying the cname
aliases we announce.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Both IETF and POSIX allow longer hostname, 253 and 255, which Linux does
not support. Since Linux 1.0 the maximum has been 64 US-ASCII characters.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
These callback are not the primary responisble for the property, but
want to be informed of any changes. E.g., /system/hostname changes
should also update the adminurl in all mDNS records.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Relocate all nginx .conf files to board/common/rootfs/etc/nginx/ and
introduce available/*.conf with symlinks to enabled/*.conf
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Align both qemu targets for 'make run' to use kvm with tcg as fallback
and -cpu max instead of guessing. This allows running Infix on systems
that do not have, or do not allow, kvm acceleration.
This is a temporary fix before we refactor 'make run', see issue #388
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The container tests utilize the bundled curios-httpd, which clashes with
the new web services provided by nginx. So we need to disable it while
testing all the containers.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This commit adds an initial YANG model for Infix web services under the
infix-services.yang umbrella. For now the nginx server statements in
/etc/nginx/nginx.conf are always on, but the backend ttyd, and the
entire nginx server can be disabled.
The default in the YANG model for both is disabled, the factory-config
has been updated to enable these services by default.
The Web Console Interface mDNS service has been updated to advertise
on port 7681, which nginx is set to forward to ttyd.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Refactor setup to automatically redirect http -> https, dropping
the /browse location for now.
Also, log to syslog, which has log rotation.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Joachim Wiberg