Everything (!) potentially shared with other sysrepo plugins/daemons and
helper functions (not yet in libite) that can be used by other daemons
have been relocated to libsrx.
Fix#116
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This patch drops auto-enable of services we want to be able to control
via NETCONF/YANG. SSDP and mDNS/SD enable/disable configure support,
using native models, will be included in the same PR and LLDP+SNMP may
come later, using std. IEEE/IETF models, they are not critical atm.
Fix#118
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
On some system, certain interfaces are not usable by an end-user. The
canonical example of this is the ethernet MAC connected to a switch,
i.e. the DSA port.
Avoid having these be picked up in the generated factory-config, which
would be confusing to a user, by classifying them as "internal" ports
to be ignored by confd and friends.
For some reason, the controller disables the bus power sometime after
it was enabled by the driver. The reference manual says, in Table 645,
about the SD_BUS_POWER bit:
> ... It will be cleared if one of the following occurs: the
> sd_bus_vlt and the voltage support in the Capabilities Register 1 do
> not match or if a card removal state was detected.
Further investigation will be needed to find the (electrical?)
root-cause of this issue.
The kernel's mounting of the rootfs may race against the underlying
device being probed - especially for media like MMC cards and USB
sticks.
Therefore, tell the kernel to wait for the root device to show up.
In the future we want to build disk images from builds where we
haven't locally built Infix, we've just downloaded an existing
release. In those cases we also have to create rauc.status, even
though we're not creating a bundle.
This is the layout expected by the "distro boot" effort in U-Boot.
As far as I understand, the contract is:
- U-Boot built for `fooboard` by `vendor`, will set the `fdtfile`
variable to `vendor/fooboard.dtb` - or more precisely: matching
whatever path the dtb is built at in the kernel tree.
- A distro (e.g. Infix) then just needs to specify the `fdtdir` in its
syslinux config (/boot in our case), and U-Boot will be able to find
the correct dtb.
Make the traditional FITs smaller by:
- Filtering out the kernel image from the rootfs, since the FIT way is
to ship it separately.
- Gzipping the kernel in the FIT, since aarch64 uses the uncompressed
"Image" format, and squashfs won't take care of it for us.
Add source, such as "ethernet" to the show ietf interfaces command.
This is translated from the somewhat obscure ietf type, such as
iana-if-type:ethernetCsmacd => ethernet
Signed-off-by: Richard Alpe <richard@bit42.se>
Replace the old "ip" output with data from the sysrepo operational
datastore. This data is piped through the new json-cfg-pretty script,
which formats the data in a nice human readable way.
Signed-off-by: Richard Alpe <richard@bit42.se>
Add IPv4 address info from "ip addr" json to sysrepo operational
datastore.
This patch adds: MTU and ip with prefix-length.
Signed-off-by: Richard Alpe <richard@bit42.se>
The commit adds a missing description and reorders some yang statements
to meet canonical ordering according to RFC7950, section 14.
It also relocates the /interfaces/interfaces/infix-if:port augment to
its own base model that the bridge (and later lag) models reference.
Solving the bisarre ordering issues we've seen previously.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This patch adds a new infix-interface-type, derived from the IANA base
type, allowing us to limit the list of supported native interface types.
Basing on IANA interface type ensure compatibility with other models,
e.g., standard/ieee/published/802.3/ieee802-ethernet-interface.yang,
which attaches itself to all interfaces of type ianaift:ethernetCsmacd.
Tested with yanglint and in Infix using ieee802-ethernet-interface.yang,
the 'ethernet' container was properly attached to interfaces of type
infixift:ethernet.
Tab completion in the CLI now lists only the supported types.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This further locks down confd to fall back to /bin/false as login shell
in case of internal errors.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This patch restricts the possible user shells to a subset of the list in
/etc/shells, which is generated by Buildroot. The default is 'false' to
prevent accidental shell access for non-admin role users.
The default shell for the admin user is now /bin/clish, which can be
further locked down before Infix v24.02 LTS.
In case of internal error the default fallback shell is now set to the
customizable LOGIN_SHELL, which currently is /bin/bash.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The following changes have been made to condense and simplify the
leading text in the README. Tested with Grip to verify that the first
paragraph flows nicely to the left to the fine new logo. This allows
us to use the space more efficiently and the reader does not have to
scroll so long before reaching relevant content.
- Right-align logo, and shrink it a bit, to fit text to the left
- Move topic links to a foldout at the top
- Move boring licensing stuff to separate docment
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Go for something simple - Tux trapped in an RJ45 jack.
Also, remove the old versions that we don't use any more. They're in
the log if we ever need them.
This is a cleanup and reorganization of the Infix documentation.
Starting with a simplification of the top-level README, splitting
it up into several pages.
Also, fixes#100 by updating the documentation on Qemu.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Also renames all klix_SYM@klinfix to SYM@infix, this is fine since we're
always calling these symbols with @infix.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- Always respect the requested model to emulate. Before this change, a
device configured to run in TAP mode would ignore a user's requested
model and always emulate a e1000.
This worked on x86_64 where that driver is part of the kernel, but
that is not true for aarch64.
- Always supply a mactab. It was very confusing that the interface
names would change, in Infix, depending on the selected networking
mode.
- Remove old decoy variables that were assigned but never used
anywhere.
- Separately setup the host and target side of a nic (i.e. use a
-netdev/-device pair instead of the -nic shortcut). This lets us
share the host side setup across all modes.
