This update enhances the LLDP configuration by enabling per-port
administration through the `admin-status` parameter. Users can now
individually enable or disable LLDP operation on specific ports.
Fixes#578
On slow systems, we don't want test steps involving tools like scp or
ssh-keyscan to fail because the server had not come up yet.
Therefore, make sure that the server is ready to accept connections
before moving on to subsequent test steps.
Use CAPTIALIZED names for static data and collect them at the top.
Make a note about for future readers about why a test called
ssh_key_authentication suspiciously does not enable the SSH service :)
Being able to check for a TCP based service is generally useful, not
only for NETCONF. Therefore, break it out to a separate function that
allows any port to be queried.
Due to #902 (which has not been root caused at this time), podman may
indicate the existance of an interface that yanger is not able to
locate in any namespace. Therefore, make sure that we verify that the
interface was actually found before trying to create the operational
data for it.
Break up the --test parameter into either:
--capture: Write system command output to a local directory for later
consumption by...
--replay: Which can replay a previous capture
Rename --wrap-commands => --cmd-prefix
This change introduces the configuration of the tx-interval parameter
for the LLDP service, allowing control over the frequency of LLDP hello
messages. This improvement eliminates the need to toggle the interface
down and up to force the emission of LLDP packets in the test
environment.
This should be a non functional change. The idea is to use the topdoc
dir from 9pm when generating the test report.
Signed-off-by: Richard Alpe <richard@bit42.se>
Useful to only create a new image with only small diff with for example
aarch64_defconfig.
example:
If the only diff is the VENDOR, instead of KernelKit you want 'foobar'.
create a file with the change:
INFIX_VENDOR="foobar"
and call ./utils/generate-defconfig.sh -b aarch64_defconfig -c foobar-diff.conf -o configs/foobar_defconfig
Existing tests relied on manually captured system data from various
points in Infix's history, making them hard to extend as we add new
features.
Move to a new model where we:
To update a unit test:
1. Use Infamy tests to setup a DUT in a known state
2. Use yanger's wrapper mode to capture the system state needed to
produce operational data for a set of YANG models
3. Use cli-pretty to create the expected output for a set of show
commands
When running unit tests, we can then use the captured data to verify
that yanger and cli-pretty works as expected without the need for a
running Infix system - just like before. The difference is that it is
now much easier to capture a new snapshot when the system evolves.
Ensure that all flavors of GRE tunnels can be configured. In addition
to the increased test coverage, it will also be useful as a basis for
collecting representative system state for CLI testing.
Ensure that VLANs can be configured on VLAN filtering bridges. In
addition to the increased test coverage, it will also be useful as a
basis for collecting representative system state for CLI testing.
Allow all host commands to be run with a prefix (e.g. `ssh
user@remotehost sudo`), such that yanger can be tested against the
current state of a remote system.
If a command wrapper _and_ a test directory is specified, the output
of all commands and files are recorded for use by a future test
execution.
Example:
1. Launch a `make run` instance and setup some config for which we
want to test yanger and cli-pretty
2. Capture the output of all commands needed to produce the data for
some YANG model:
`yanger -t /tmp/ifs -w "ixll -A ssh qtap1 sudo" ietf-interfaces`
3. Kill the instance (we do not need it any more)
4. Test cli-pretty using the captured state:
`yanger -t /tmp/ifs ietf-interfaces | cli-pretty show-interfaces
`
The default was set to only accept connections from localhost when
connecting via IPv6. This was not caught in testing since the
test-config accepts connections from all hosts (::).
Accept connections from all hosts in all builtin configs. Inherit
test-config's service definition from factory-config, since we want
testing to be done as close as possible to what are users are running.
The default ping(8) shipped with alpine does not support `ping <addr>
-c1`, but happily executes `ping -c1 <addr>`. Therefore, make sure
that the address is always the last argument.
Mattias Walström