- Add a board README to explain how to get Infix running
- Update mkimage.sh to allow creating images without boot loader
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add board support for the BananaPi BPI-R4 router board, based on the
MediaTek MT7988A (Filogic 880) SoC with quad-core Cortex-A73 CPU.
The BPI-R4 is the successor to the BPI-R3 but uses entirely different
silicon: the internal switch runs at 2.5 GbE per port, the two SFP+
uplinks use native USXGMII at up to 10 Gbps, and WiFi is provided by
a MediaTek MT7996E PCIe module supporting tri-band WiFi 7 (2.4/5/6 GHz).
Two board variants, BPI-R4-2g5 and BPI-R4P, replace one SFP+ cage with
a 2.5 GbE RJ45 port (using the MT7988A internal 2.5G PHY); the R4P adds
an optional PoE daughterboard on that port. Both use the upstream
mt7988a-bananapi-bpi-r4-2g5 device tree.
Interfaces:
- Standard R4: eth1 (gmac1/sfp2 LAN cage) → sfp2, eth2 (gmac2/sfp1 WAN cage) → sfp1
- R4-2g5/R4P: eth1 (2.5G PHY) → wan, eth2 (gmac2/sfp1 WAN cage) → sfp1
Factory reset / WPS button (GPIO14, active-low): detected by U-Boot at
boot for factory reset; reused by Linux as KEY_WPS_BUTTON at runtime.
eMMC install note: the MT7988A eMMC (pins 38-49) and SD card (pins 32-37)
use separate physical pads so there is no electrical bus sharing, unlike
some BPi-R3 configurations. However, a single MMC controller
(mmc@11230000) handles both, so only one is active per boot session.
The eMMC install procedure therefore still requires an intermediate SPI
NAND bootloader step until a Linux-side install path is tested.
SD card build (bpi_r4_sd_boot_defconfig) now uses the new
mt7988a_bpir4_sd U-Boot defconfig with cap-sd-highspeed enabled,
giving 50 MHz SD transfers instead of the previous 25 MHz legacy mode.
Also adds MT7988/MT7996 firmware support to the buildroot linux-firmware
package, for 2.5 GbE port PHY and WiFi7 extension board, and updates the
aarch64_defconfig, aarch64_minimal_defconfig, the arch README, CI
boot/image workflows, mkimage.sh, and the ChangeLog.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add board support for the BananaPi BPi-R64 router board, based on the
MediaTek MT7622 SoC and MT7531 Gigabit Ethernet switch.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The awk insertion path used getline to peek at the line right after the
"### Changes", but only printed it when NF == 0 (blank line). If the
section already had a non-blank entry (e.g. a Buildroot upgrade line),
getline consumed it silently and the kernel line was written in its
place.
Fix by adding the missing else branch so the consumed line is always
re-emitted — blank lines before the new entry, non-blank lines after it.
Also demote the missing-UNRELEASED guard from exit 1 to a warning with
return 0, so the workflow doesn't abort when a new release cycle hasn't
had its ChangeLog section opened yet.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Apple devices (e.g. Apple TV) publish vv=1 in their AirPlay/RAOP TXT
records, causing a false positive with our Infix platform marker.
Tighten the filter to require vv=1 together with at least one management
service type (ssh, https, http, netconf, restconf), which Apple devices
never advertise. Keep on=Infix as a fallback for older firmware that
predates vv=1.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Introduce libfleet.sh and a new 'fleet' subcommand to ixll for managing
and operating enrolled Infix devices via RESTCONF.
Device configuration is stored in ~/.config/infix/config.json
(chmod 600): and organised by profile, allowing bulk operations across
groups of devices (e.g. all aarch64 targets).
New commands:
ixll fleet enroll [-d] [-p profile] [-u user] [-w password] <name> <address>
ixll fleet list
ixll fleet upgrade <name|profile> <url>
ixll fleet backup [-o dir] <name|profile>
ixll fleet reboot <name|profile>
Upgrade runs in parallel across a fleet and shows a live per-device
progress bar by polling the infix-system:install-bundle RPC and the
installer state from the YANG operational data store.
The global -A flag (admin/admin) is honoured as a credential fallback
for devices enrolled without an explicit password.
Also fix a pre-existing typo: ">2" → ">&2" in the error path.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This is a simple two port router board, with the same
WiFi chips as BPI-r3.
The bootloader shall be the same as the BPI-r3, the bootloader
now probes which of the two is booting by checking for the PHYS
that only exist on BPI-r3-mini.
All build scripts use $BR2_ARCH to determine location of critical board files
and configuration. As per previous decisions, the BR2_ARCH variable controls
all naming in Infix and for consistency the defconfig files are also renamed.
This fixes the issue with missing DTB file(s) for the Raspberry Pi 2B.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Release tarballs waste ~131MB per architecture by including both
rootfs.itb and rootfs.squashfs, even though rootfs.itb already
contains the squashfs (itb = 4096-byte header + squashfs).
This change removes rootfs.squashfs from releases and provides two
solutions for users who need it:
1. utils/extract-squashfs.sh - Full-featured utility for extracting
squashfs from release tarballs or .itb files. Includes validation
and helpful error messages.
2. board/common/qemu/qemu.sh - Auto-extraction support. When running
in initrd mode, automatically extracts rootfs.squashfs from
rootfs.itb if missing. Zero user impact - ./qemu.sh just works!
Space savings: ~262MB per release (2 architectures × 131MB)
Fixes#858
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Split download and MD5 computation into separate functions for clarity.
Add proper error handling for HTTP 404 and network errors. Improve help
text to mention appliances/ directory location.
[skip ci]
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This commit adds support to simplify sdcard.img generation by downloading the
latest bootloader build for a board from the 'latest-boot' release tag. The
tarball is saved in dl/bootloader/ and is extracted to a temporary directory
in output/build/boot-$board-xxxx on every invocation of mkimage.sh. This is
used for invoking genimage and bmaptool before copying the resulting images
to output/images/. (If $O is set, it is used instead of output/, above).
New options:
-d Download latest bootloader build for the given board
-f Force re-download even if bootlaoder tarball existgs
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This commit consolidates mkimage.sh scripts into a unified SD card image
creation tool that works for all boards. It needs a bootloader an $ARCH
rootfs.squashfs image and a genimage.cfg.in template.
- Detects build directories from `O=` environment variable or `output/`
- Sources `.config` to discover Buildroot paths
- Uses Buildroot's `support/scripts/genimage.sh` when available
- Automatically generates `.bmap` files if `bmaptool` is available
- Fallback to direct `genimage` invocation if wrapper not found
See the online instructions for usage.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This will fix#1106, in time, but only allows manual trigger for now,
needs more test and verification
utils/kernel-upgrade.sh at least automate all the manual manual processes
for upgrading the kernel.
The curl.sh wrapper script had several issues:
- Used 'shift 2' incorrectly without proper argument validation
- Required hostname as enviroment variable instead of option
- Lacked proper option parsing, should behave like a cross between
curl and sysrepocfg
All examples have been updated to match the refactored script, and
a local copy in utils/curl.sh has been added.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
You need first to clone gns3-registry from https://github.com/GNS3/gns3-registry
Follow this steps:
1. ./utils/bump-gns3.py 25.08.0 ../../gns3/gns3-registry/appliances/infix.gns3a
2. TEST in gns3, just add the new version, start it.
3. run python3 check.py inside gns3-registry, verify infix is ok.
4. Create a pull request to gns3-registry
This fix#1107
If a extra infix feature require features to be added to an already
loaded module. Instead of have the exact module definition in multiple
places (with date), this will allow a much more flexible sytax:
MODULES=(
"infix-interfaces -e containers"
)
This require that the infix-interfaces is loaded *before* this file
is run.
- Update usage text for readability, add example
- Reindent getopts case and add -h
- Allow 'git rm -f' to remove already staged patches
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Mattias Walström