Build the mkdocs User's Guide into WebUI images and surface it in the UI.
post-build.sh runs `mkdocs build` from the top-level mkdocs.yml into
/var/www/guide when the webui package is selected and mkdocs is on the
build host; nginx serves it read-only at /guide/. The build is
best-effort — a missing mkdocs warns and ships without the guide rather
than failing — and minimal images (no webui) skip it.
The WebUI gates a book icon in the topbar and a User Guide item in the
user menu on the docs being present on disk (os.Stat, fail-closed), both
opening /guide/ in a new tab.
CI: a local setup-mkdocs composite action installs mkdocs and the
plugins from mkdocs.yml; the build and release workflows run it before
the build so images produced in CI include the guide. developers-guide
documents the new build dependency and restores the missing
mkdocs-glightbox plugin.
Fixes#633
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
When an interface has been handed off to a container it lives in
another netns, so `ip neigh/addr flush dev FOO` fails on the host.
The failure aborts dagger, and since interfaces_change() runs before
containers_change() in change_cb(), the container delete path is
never reached -- the stale container keeps the interface trapped in
its netns, breaking the next reconfiguration.
Guard both the neighbor and address flush exit scripts with
`if_nametoindex(ifname)` -- true exactly when the interface is in
the host netns, false for both "in a container" and "already gone".
This replaces the pre-existing `!cni_find(ifname) && if_nametoindex(
ifname)` guard at the addr site: cni_find() added no information
for this check and would popen(container find) for nothing when the
interface had been deleted entirely.
Also harden wrap() in /usr/sbin/container so a stale setup pidfile
doesn't short-circuit Finit's stop attempt -- kill the setup PID and
still ask podman to stop the container.
Fixes#1493
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The mt7622 soc has a built-in wmac, same driver as the mt7615, but
it lacked MODULE_DEVICE_TABLE() so udev could not autoload driver
and firmware.
This commit also adds the wmac+bluetooth specific firmware.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The U-Boot env file is generated by
mkenvimage, which prefixes the variable data with a 4-byte CRC32 by default.
ixpreboot.sh previously imported it with `env import -b` as per uboot docs(-b assume binary format (’0’ separated, “00” terminated).),
which treats the buffer as raw binary and does not strip the CRC.
As a result the first variable's name is parsed a part of CRC.
Later variables import correctly because by then the parser is past the CRC.
Switching to `env import -c` as per uboot docs (-c assume checksum protected environment format.)
makes U-Boot validate and strip the CRC before parsing, so the first variable imports under its real name.
Tested on:
- QEMU
Signed-off-by: Ejub Sabic <ejub1946@outlook.com>
On multi-chip DSA hardware (e.g., boards with multiple mv88e6xxx
chips), each switch chip has its own independent PHC device. With
boundary_clock_jbod enabled, ptp4l starts but only disciplines the
active slave port's PHC — the others drift.
Automatically start phc2sys -a alongside any BC or TC instance using
hardware timestamping. It subscribes to ptp4l's UDS socket, tracks
BMCA, and disciplines all non-active PHCs to match the active one.
On single-chip hardware it is a harmless no-op.
CLOCK_REALTIME is intentionally left untouched. Syncing the system
clock to PTP (phc2sys -rr), feeding the PHC from GPS/NTP (ts2phc,
phc2sys reverse), and full multi-source coordination (timemaster) are
planned as follow-on phases; see the issue tracker for the roadmap.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
NOTE: this is intended only for use on devboards like EspressoBin where
the onboard bootloader only understands fat and ext2 file systems.
To enable, use 'make apply-ext4'
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Inverted values for eMMC and SPI NAND. Also use ABCD instead of
Position as column name to match board markings.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- Add a board README to explain how to get Infix running
- Update mkimage.sh to allow creating images without boot loader
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Also, simplify board README a bit now that we know that you don't need
to flip the boot switch to program eMMC.
[skip ci]
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add missing *.hash files for all board packages using the ix-board macro;
they declare LICENSE_FILES = LICENSE but had no hash file, producing a
warning during make legal-info.
Fix the date-cpp package where the hash file was named date.hash instead
of date-cpp.hash (package name is derived from the directory, not the mk
filename), causing Buildroot to skip the hash check entirely.
Add hash files for local-site packages confd-test-mode, netd, and
onieprom that declared LICENSE_FILES but provided no hash.
Also, rename package/date-cpp/date.mk to date-cpp.mk. Buildroot derives
the package name from the directory name, so the mk file must match. To
handle the archive name different we set DATE_CPP_SOURCE.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add board support for the BananaPi BPI-R4 router board, based on the
MediaTek MT7988A (Filogic 880) SoC with quad-core Cortex-A73 CPU.
The BPI-R4 is the successor to the BPI-R3 but uses entirely different
silicon: the internal switch runs at 2.5 GbE per port, the two SFP+
uplinks use native USXGMII at up to 10 Gbps, and WiFi is provided by
a MediaTek MT7996E PCIe module supporting tri-band WiFi 7 (2.4/5/6 GHz).
Two board variants, BPI-R4-2g5 and BPI-R4P, replace one SFP+ cage with
a 2.5 GbE RJ45 port (using the MT7988A internal 2.5G PHY); the R4P adds
an optional PoE daughterboard on that port. Both use the upstream
mt7988a-bananapi-bpi-r4-2g5 device tree.
Interfaces:
- Standard R4: eth1 (gmac1/sfp2 LAN cage) → sfp2, eth2 (gmac2/sfp1 WAN cage) → sfp1
- R4-2g5/R4P: eth1 (2.5G PHY) → wan, eth2 (gmac2/sfp1 WAN cage) → sfp1
Factory reset / WPS button (GPIO14, active-low): detected by U-Boot at
boot for factory reset; reused by Linux as KEY_WPS_BUTTON at runtime.
eMMC install note: the MT7988A eMMC (pins 38-49) and SD card (pins 32-37)
use separate physical pads so there is no electrical bus sharing, unlike
some BPi-R3 configurations. However, a single MMC controller
(mmc@11230000) handles both, so only one is active per boot session.
The eMMC install procedure therefore still requires an intermediate SPI
NAND bootloader step until a Linux-side install path is tested.
SD card build (bpi_r4_sd_boot_defconfig) now uses the new
mt7988a_bpir4_sd U-Boot defconfig with cap-sd-highspeed enabled,
giving 50 MHz SD transfers instead of the previous 25 MHz legacy mode.
Also adds MT7988/MT7996 firmware support to the buildroot linux-firmware
package, for 2.5 GbE port PHY and WiFi7 extension board, and updates the
aarch64_defconfig, aarch64_minimal_defconfig, the arch README, CI
boot/image workflows, mkimage.sh, and the ChangeLog.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add --log-level command line option to filter out log messages from
lower log levels. Then fix the annoying CzechLight warning message
and useless "NACM config validation" log. Then add audit trail as
we have in netopeer2-server, and finish off by stripping redundant
fields from log message: timestamp, identity, and log level.
Fixes#892
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Previously svc_enadis() would call 'initctl enable + touch' for every
config change event, even when the service's enabled state was unchanged.
This caused rousette to be unnecessarily restarted on every test_reset(),
racing with the active RESTCONF connection on slow hardware.
Replace svc_enadis() and svc_change() with svc_enable() which only
manages nginx symlinks and calls 'initctl enable/disable' -- never touch.
Each handler now checks the diff for the specific leaf that changed:
- If /enabled appears in diff: call svc_enable() to start or stop it
- If other config leaves changed with service already enabled: touch only
This ensures rousette, ttyd, netbrowse, avahi, sshd, and lldpd are only
restarted when their configuration actually requires it.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- Add x509-public-key-format identity to crypto-types
- Add certificate node to web services container
- Use certificate from ietf-keystore as web cert
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Neither the Raspberry Pi 2B or the Microchip SAMA7G54-EK board have WiFi
hardware by default so drop WiFi, and GPS, support to allow for smaller
builds with only the bare essentials in kernel and system.
Minimal builds in general don't need WiFi or GPS either, so let's disable
them from all. This may become a central theme going forward, keeping
the minimal builds ... minimal.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
netopeer2 and rousette were starting as soon as confd had a PID, while
confd was still loading the startup config via sr_replace_config(). This
held a write lock on the running datastore. A test calling test/reset
shortly after the NETCONF port opened would have its own sr_replace_config()
block on that lock for up to 60 s, at which point sysrepo timed out the
whole RPC with "SHM event 'rpc' processing timed out".
Fix by adding the usr/bootstrap condition to both management servers so
they don't accept connections until confd signals that bootstrap is complete.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Relocate probe of wifi radios from gen-hardware to 00-probe. This saves
one python invocation and some precious CPU cycles at boot.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Follow-up to 90f619b which first introduced the /etc/hostname.d concept.
This commit moves the setup of /etc/hostname.d to post-build.sh dropping
the initial call to the hostname activation script a bit, since it is
called anyway after bootstrap has finished. The scrip is also given a
bit of a refrehs, reducing overhead and needless log messages.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Infix technically does not need to start dbus and dnsmasq before confd
has loaded the system startup-config. So we move it in time to save
some CPU cycles for confd & C:o.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
On single-core Cortex-A7, the YANG bootstrap and config loading is the
dominant boot bottleneck. The current sequence spawns three serial
phases (bootstrap, sysrepo-plugind, load), each performing independent
sr_connect()/sr_disconnect() cycles, and every sysrepoctl/sysrepocfg
invocation is a fork+exec that rebuilds SHM from scratch.
Replace all three with a single confd binary that does one sr_connect()
and performs all datastore operations in-process:
- Wipe stale /dev/shm/sr_* for a clean slate
- sr_install_factory_config() from the generated JSON
- Smart migration: compare config version via libjansson, only
fork+exec the migrate script when versions actually differ
- Load startup-config (or test-config) via lyd_parse_data() +
sr_replace_config(), mirroring what sysrepocfg -I does internally
- On failure: revert to factory-default, load failure-config, set
login banners (Fail Secure mode)
- On first boot: copy factory-default to running, export to file
- dlopen plugins and enter event loop
The bootstrap shell script is split: config generation (gen-hostname,
gen-interfaces, etc.) stays in the new gen-config script, while all
sysrepo operations move into the C daemon. The finit boot sequence
collapses from 5 stanzas to 2 (gen-config -> confd).
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- The biggest changes are syncing with latest BusyBox (busybox-update-config)
- Disable optimize for size
- Enable feature "SH_NOFORK" which allows /bin/sh to call applet_main()
directly without having to fork+exec busybox
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Mattias Walström