mirror of
https://github.com/kernelkit/infix.git
synced 2026-07-22 01:13:00 +02:00
Joachim Wiberg
31df56308b
Add board support for the BananaPi BPI-R4 router board, based on the MediaTek MT7988A (Filogic 880) SoC with quad-core Cortex-A73 CPU. The BPI-R4 is the successor to the BPI-R3 but uses entirely different silicon: the internal switch runs at 2.5 GbE per port, the two SFP+ uplinks use native USXGMII at up to 10 Gbps, and WiFi is provided by a MediaTek MT7996E PCIe module supporting tri-band WiFi 7 (2.4/5/6 GHz). Two board variants, BPI-R4-2g5 and BPI-R4P, replace one SFP+ cage with a 2.5 GbE RJ45 port (using the MT7988A internal 2.5G PHY); the R4P adds an optional PoE daughterboard on that port. Both use the upstream mt7988a-bananapi-bpi-r4-2g5 device tree. Interfaces: - Standard R4: eth1 (gmac1/sfp2 LAN cage) → sfp2, eth2 (gmac2/sfp1 WAN cage) → sfp1 - R4-2g5/R4P: eth1 (2.5G PHY) → wan, eth2 (gmac2/sfp1 WAN cage) → sfp1 Factory reset / WPS button (GPIO14, active-low): detected by U-Boot at boot for factory reset; reused by Linux as KEY_WPS_BUTTON at runtime. eMMC install note: the MT7988A eMMC (pins 38-49) and SD card (pins 32-37) use separate physical pads so there is no electrical bus sharing, unlike some BPi-R3 configurations. However, a single MMC controller (mmc@11230000) handles both, so only one is active per boot session. The eMMC install procedure therefore still requires an intermediate SPI NAND bootloader step until a Linux-side install path is tested. SD card build (bpi_r4_sd_boot_defconfig) now uses the new mt7988a_bpir4_sd U-Boot defconfig with cap-sd-highspeed enabled, giving 50 MHz SD transfers instead of the previous 25 MHz legacy mode. Also adds MT7988/MT7996 firmware support to the buildroot linux-firmware package, for 2.5 GbE port PHY and WiFi7 extension board, and updates the aarch64_defconfig, aarch64_minimal_defconfig, the arch README, CI boot/image workflows, mkimage.sh, and the ChangeLog. Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
345 lines
12 KiB
YAML
345 lines
12 KiB
YAML
name: Create SD Card & eMMC Images
|
|
|
|
on:
|
|
workflow_dispatch:
|
|
inputs:
|
|
board:
|
|
description: 'Board to create image for'
|
|
type: choice
|
|
required: true
|
|
options:
|
|
- raspberrypi-rpi2
|
|
- raspberrypi-rpi64
|
|
- bananapi-bpi-r3
|
|
- bananapi-bpi-r4
|
|
- bananapi-bpi-r64
|
|
- friendlyarm-nanopi-r2s
|
|
- microchip-sama7g54-ek
|
|
default: 'raspberrypi-rpi64'
|
|
|
|
jobs:
|
|
create-image:
|
|
name: Create SD Card Image for ${{ inputs.board }}
|
|
runs-on: ubuntu-latest
|
|
steps:
|
|
- name: Checkout repository
|
|
uses: actions/checkout@v4
|
|
with:
|
|
clean: true
|
|
fetch-depth: 0
|
|
submodules: recursive
|
|
|
|
- name: Install dependencies
|
|
run: |
|
|
sudo apt-get update
|
|
sudo apt-get install -y \
|
|
genimage \
|
|
u-boot-tools \
|
|
parted \
|
|
gdisk \
|
|
qemu-utils \
|
|
dosfstools \
|
|
e2fsprogs \
|
|
genext2fs \
|
|
mtools \
|
|
jq
|
|
|
|
- name: Prepare build environment
|
|
run: |
|
|
# Set up directory structure similar to buildroot build
|
|
mkdir -p output/images
|
|
mkdir -p build
|
|
|
|
- name: Set bootloader and target based on board
|
|
run: |
|
|
case "${{ inputs.board }}" in
|
|
raspberrypi-rpi2)
|
|
echo "BOOTLOADER=rpi2-boot" >> $GITHUB_ENV
|
|
echo "ARCH=arm" >> $GITHUB_ENV
|
|
echo "BUILD_EMMC=false" >> $GITHUB_ENV
|
|
;;
|
|
raspberrypi-rpi64)
|
|
echo "BOOTLOADER=rpi64-boot" >> $GITHUB_ENV
|
|
echo "ARCH=aarch64" >> $GITHUB_ENV
|
|
echo "BUILD_EMMC=false" >> $GITHUB_ENV
|
|
;;
|
|
bananapi-bpi-r3)
|
|
echo "BOOTLOADER_SD=bpi-r3-sd-boot" >> $GITHUB_ENV
|
|
echo "BOOTLOADER_EMMC=bpi-r3-emmc-boot" >> $GITHUB_ENV
|
|
echo "ARCH=aarch64" >> $GITHUB_ENV
|
|
echo "BUILD_EMMC=true" >> $GITHUB_ENV
|
|
;;
|
|
bananapi-bpi-r4)
|
|
echo "BOOTLOADER_SD=bpi-r4-sd-boot" >> $GITHUB_ENV
|
|
echo "BOOTLOADER_EMMC=bpi-r4-emmc-boot" >> $GITHUB_ENV
|
|
echo "ARCH=aarch64" >> $GITHUB_ENV
|
|
echo "BUILD_EMMC=true" >> $GITHUB_ENV
|
|
;;
|
|
bananapi-bpi-r64)
|
|
echo "BOOTLOADER_SD=bpi-r64-sd-boot" >> $GITHUB_ENV
|
|
echo "BOOTLOADER_EMMC=bpi-r64-emmc-boot" >> $GITHUB_ENV
|
|
echo "ARCH=aarch64" >> $GITHUB_ENV
|
|
echo "BUILD_EMMC=true" >> $GITHUB_ENV
|
|
;;
|
|
friendlyarm-nanopi-r2s)
|
|
echo "BOOTLOADER=nanopi-r2s-boot" >> $GITHUB_ENV
|
|
echo "ARCH=aarch64" >> $GITHUB_ENV
|
|
echo "BUILD_EMMC=false" >> $GITHUB_ENV
|
|
;;
|
|
microchip-sama7g54-ek)
|
|
echo "BOOTLOADER_SD=sama7g54-ek-sd-boot" >> $GITHUB_ENV
|
|
echo "BOOTLOADER_EMMC=sama7g54-ek-emmc-boot" >> $GITHUB_ENV
|
|
echo "ARCH=arm" >> $GITHUB_ENV
|
|
echo "BUILD_EMMC=true" >> $GITHUB_ENV
|
|
;;
|
|
*)
|
|
echo "Error: Unknown board ${{ inputs.board }}"
|
|
exit 1
|
|
;;
|
|
esac
|
|
echo "Arch: $ARCH for board: ${{ inputs.board }}"
|
|
if [ "$BUILD_EMMC" = "true" ]; then
|
|
echo "Building both SD and eMMC images"
|
|
echo "SD Bootloader: $BOOTLOADER_SD"
|
|
echo "eMMC Bootloader: $BOOTLOADER_EMMC"
|
|
else
|
|
echo "Building SD image only"
|
|
echo "Bootloader: $BOOTLOADER"
|
|
fi
|
|
|
|
- name: Download bootloader artifacts
|
|
run: |
|
|
# Download bootloader from latest-boot release tag
|
|
if [ "$BUILD_EMMC" = "true" ]; then
|
|
# Download both SD and eMMC bootloaders for boards that support both
|
|
echo "Downloading SD bootloader: ${BOOTLOADER_SD}"
|
|
gh release download latest-boot --pattern "*${BOOTLOADER_SD}*" --dir temp_bootloader_sd/
|
|
mkdir -p output_sd/images
|
|
cd temp_bootloader_sd/
|
|
tar -xzf *.tar.gz --strip-components=1 -C ../output_sd/images/
|
|
cd ../
|
|
rm -rf temp_bootloader_sd/
|
|
|
|
echo "Downloading eMMC bootloader: ${BOOTLOADER_EMMC}"
|
|
gh release download latest-boot --pattern "*${BOOTLOADER_EMMC}*" --dir temp_bootloader_emmc/
|
|
mkdir -p output_emmc/images
|
|
cd temp_bootloader_emmc/
|
|
tar -xzf *.tar.gz --strip-components=1 -C ../output_emmc/images/
|
|
cd ../
|
|
rm -rf temp_bootloader_emmc/
|
|
|
|
echo "SD bootloader files:"
|
|
ls -la output_sd/images/
|
|
echo "eMMC bootloader files:"
|
|
ls -la output_emmc/images/
|
|
else
|
|
# Single bootloader for boards that only support SD
|
|
gh release download latest-boot --pattern "*${BOOTLOADER}*" --dir temp_bootloader/
|
|
|
|
# Extract bootloader directly to output/images
|
|
cd temp_bootloader/
|
|
tar -xzf *.tar.gz --strip-components=1 -C ../output/images/
|
|
cd ../
|
|
rm -rf temp_bootloader/
|
|
|
|
echo "Bootloader files extracted to output/images:"
|
|
ls -la output/images/
|
|
fi
|
|
env:
|
|
GH_TOKEN: ${{ secrets.GITHUB_TOKEN }}
|
|
|
|
- name: Download Infix artifacts
|
|
run: |
|
|
# Download from latest Kernelkit Trigger workflow for main branch
|
|
gh run list --workflow=164295764 --branch=main --limit=1 --status=success --json databaseId --jq '.[0].databaseId' > latest_infix_run_id
|
|
INFIX_RUN_ID=$(cat latest_infix_run_id)
|
|
|
|
if [ "$BUILD_EMMC" = "true" ]; then
|
|
# Copy Infix artifacts to both SD and eMMC output directories
|
|
gh run download ${INFIX_RUN_ID} --name artifact-${ARCH} --dir temp_infix/
|
|
|
|
cd temp_infix/
|
|
tar -xzf *.tar.gz --strip-components=1 -C ../output_sd/images/
|
|
tar -xzf *.tar.gz --strip-components=1 -C ../output_emmc/images/
|
|
cd ../
|
|
rm -rf temp_infix/
|
|
|
|
echo "Infix files extracted to output_sd/images:"
|
|
ls -la output_sd/images/
|
|
echo "Infix files extracted to output_emmc/images:"
|
|
ls -la output_emmc/images/
|
|
else
|
|
# Single output directory for SD-only boards
|
|
gh run download ${INFIX_RUN_ID} --name artifact-${ARCH} --dir temp_infix/
|
|
|
|
# Extract Infix directly to output/images
|
|
cd temp_infix/
|
|
tar -xzf *.tar.gz --strip-components=1 -C ../output/images/
|
|
cd ../
|
|
rm -rf temp_infix/
|
|
|
|
echo "Infix files extracted to output/images:"
|
|
ls -la output/images/
|
|
fi
|
|
env:
|
|
GH_TOKEN: ${{ secrets.GITHUB_TOKEN }}
|
|
|
|
- name: Verify extracted files
|
|
run: |
|
|
if [ "$BUILD_EMMC" = "true" ]; then
|
|
echo "Files available for SD image:"
|
|
ls -la output_sd/images/
|
|
echo ""
|
|
echo "Files available for eMMC image:"
|
|
ls -la output_emmc/images/
|
|
else
|
|
echo "Files available for mkimage.sh:"
|
|
ls -la output/images/
|
|
echo ""
|
|
echo "File types:"
|
|
file output/images/* || true
|
|
fi
|
|
|
|
- name: Create SD card image
|
|
run: |
|
|
if [ "$BUILD_EMMC" = "true" ]; then
|
|
export BINARIES_DIR=$PWD/output_sd/images
|
|
export BUILD_DIR=$PWD/build
|
|
export BR2_EXTERNAL_INFIX_PATH=$PWD
|
|
export RELEASE=""
|
|
export INFIX_ID="infix"
|
|
./utils/mkimage.sh -t sdcard ${{ inputs.board }}
|
|
else
|
|
export BINARIES_DIR=$PWD/output/images
|
|
export BUILD_DIR=$PWD/build
|
|
export BR2_EXTERNAL_INFIX_PATH=$PWD
|
|
export RELEASE=""
|
|
export INFIX_ID="infix"
|
|
./utils/mkimage.sh -t sdcard ${{ inputs.board }}
|
|
fi
|
|
|
|
- name: Create eMMC image
|
|
if: ${{ env.BUILD_EMMC == 'true' }}
|
|
run: |
|
|
export BINARIES_DIR=$PWD/output_emmc/images
|
|
export BUILD_DIR=$PWD/build
|
|
export BR2_EXTERNAL_INFIX_PATH=$PWD
|
|
export RELEASE=""
|
|
export INFIX_ID="infix"
|
|
./utils/mkimage.sh -t emmc ${{ inputs.board }}
|
|
|
|
- name: Verify created images
|
|
run: |
|
|
if [ "$BUILD_EMMC" = "true" ]; then
|
|
echo "SD card image:"
|
|
ls -lh output_sd/images/*-sdcard.img* 2>/dev/null || true
|
|
if ls output_sd/images/*-sdcard.img 1> /dev/null 2>&1; then
|
|
for img in output_sd/images/*-sdcard.img; do
|
|
echo "- $(basename $img)"
|
|
file "$img"
|
|
fdisk -l "$img" 2>/dev/null | head -20
|
|
done
|
|
fi
|
|
|
|
echo ""
|
|
echo "eMMC image:"
|
|
ls -lh output_emmc/images/*-emmc.img* 2>/dev/null || true
|
|
if ls output_emmc/images/*-emmc.img 1> /dev/null 2>&1; then
|
|
for img in output_emmc/images/*-emmc.img; do
|
|
echo "- $(basename $img)"
|
|
file "$img"
|
|
fdisk -l "$img" 2>/dev/null | head -20
|
|
done
|
|
fi
|
|
|
|
# Copy both images to output/images for artifact upload
|
|
mkdir -p output/images
|
|
cp output_sd/images/*-sdcard.img* output/images/ 2>/dev/null || true
|
|
cp output_emmc/images/*-emmc.img* output/images/ 2>/dev/null || true
|
|
else
|
|
echo "Contents of output/images after mkimage.sh:"
|
|
ls -lh output/images/
|
|
|
|
# Look for SD card image with pattern: *-sdcard.img
|
|
if ls output/images/*-sdcard.img 1> /dev/null 2>&1; then
|
|
echo "Found SD card image(s):"
|
|
for img in output/images/*-sdcard.img; do
|
|
echo "- $(basename $img)"
|
|
file "$img"
|
|
fdisk -l "$img" 2>/dev/null || true
|
|
done
|
|
else
|
|
echo "No SD card image found matching pattern: *-sdcard.img"
|
|
echo "Available files:"
|
|
ls -la output/images/
|
|
exit 1
|
|
fi
|
|
fi
|
|
|
|
- name: Upload images as artifacts
|
|
uses: actions/upload-artifact@v4
|
|
with:
|
|
name: images-${{ inputs.board }}
|
|
path: |
|
|
output/images/*-sdcard.img*
|
|
output/images/*-emmc.img*
|
|
retention-days: 30
|
|
|
|
- name: Create checksums
|
|
run: |
|
|
cd output/images/
|
|
for file in *-sdcard.img *-emmc.img; do
|
|
if [ -f "$file" ]; then
|
|
sha256sum "$file" > "$file.sha256"
|
|
fi
|
|
done
|
|
|
|
- name: Upload to release
|
|
uses: ncipollo/release-action@v1
|
|
with:
|
|
allowUpdates: true
|
|
omitName: true
|
|
omitBody: true
|
|
omitBodyDuringUpdate: true
|
|
prerelease: true
|
|
tag: "latest-boot"
|
|
token: ${{ secrets.GITHUB_TOKEN }}
|
|
artifacts: "output/images/*-sdcard.img*,output/images/*-emmc.img*"
|
|
|
|
- name: Generate summary
|
|
run: |
|
|
if [ "$BUILD_EMMC" = "true" ]; then
|
|
cat <<EOF >> $GITHUB_STEP_SUMMARY
|
|
# SD Card & eMMC Image Build Complete! 🚀
|
|
|
|
**Board:** ${{ inputs.board }}
|
|
**Arch:** ${{ env.ARCH }}
|
|
**SD Bootloader:** ${{ env.BOOTLOADER_SD }}
|
|
**eMMC Bootloader:** ${{ env.BOOTLOADER_EMMC }}
|
|
**Bootloader Source:** latest-boot release
|
|
**Infix Source:** Latest workflow run on main
|
|
|
|
## Created Images
|
|
$(find output/images/ -name "*.img" -o -name "*.img.bmap" | xargs ls -lh 2>/dev/null | awk '{print "- " $9 " (" $5 ")"}' || echo "- No images found")
|
|
|
|
## Download
|
|
Both SD card and eMMC images are available as workflow artifacts above and in the latest-boot release.
|
|
EOF
|
|
else
|
|
cat <<EOF >> $GITHUB_STEP_SUMMARY
|
|
# SD Card Image Build Complete! 🚀
|
|
|
|
**Board:** ${{ inputs.board }}
|
|
**Arch:** ${{ env.ARCH }}
|
|
**Bootloader:** ${{ env.BOOTLOADER }}
|
|
**Bootloader Source:** latest-boot release
|
|
**Infix Source:** Latest workflow run on main
|
|
|
|
## Created Images
|
|
$(find output/images/ -name "*.img" -o -name "*.img.bmap" | xargs ls -lh 2>/dev/null | awk '{print "- " $9 " (" $5 ")"}' || echo "- No images found")
|
|
|
|
## Download
|
|
The SD card image is available as a workflow artifact above.
|
|
EOF
|
|
fi
|