# Boot Procedure

Systems running Infix will typically boot in multiple phases, forming
a boot chain. Each link in the chain has three main responsibilities:

1. Ensuring the integrity of the next link before passing control to
   it. This avoids silent failures stemming from data corruption.
1. Ensuring the authenticity of the next link before passing control
   to it, commonly referred to as _Secure Boot_. This protects against
   malicious attempts to modify a system's firmware.
1. Preparing the system state according to the requirements of the
   next link. E.g. the Linux kernel requires the system's RAM to be
   operational.

A typical chain consists of four stages:

```
    .---------.
    |   ROM   >---.   Determine the location of and load the SPL
    '---------'   |
.-----------------'
|   .---------.
'--->   SPL   >---.   Perform DDR training and load the TPL
    '---------'   |
.-----------------'
|   .---------.
'--->   TPL   >---.   Load Linux kernel, device tree, and root filesystem
    '---------'   |
.-----------------'
|   .---------.
'--->  Infix  |       Get down to business
    '---------'
```

After a reset, hardware will pass control to a program (_ROM_) which
is almost always programmed into the SoC by the vendor.  This program
will determine the location of the _Secondary Program Loader_ (_SPL_),
typically by reading a set of _Sample at Reset_ (SaR) pins.

The _SPL_ is sometimes provided by the SoC vendor in binary form, and
is sometimes built as a part of the _Tertiary Program Loader_ (_TPL_)
build.  Its main responsibility is usually to set up the system's
memory controller and perform DDR training, if required, before
loading the _TPL_.

Commonly referred to as the system's _bootloader_, the _TPL_ is
responsible for preparing the execution environment required by the
Linux kernel.

This document's focus is to describe the final two phases of the boot
chain, as the initial phases are very hardware dependent, better
described by existing documentation provided by the SoC vendor.

## Bootloader

### Configuration

To mitigate the risk of a malicious user being able to circumvent the
bootloader's validation procedure, user configuration is kept to a
minimum.  Two settings are available:

**Boot order**: Since Infix maintains two copies of its software image,
and as some bootloaders support [netbooting][2], the order in which boot
sources are considered can be configured. To select the active
source, use [RAUC][]:

```
root@example:~# rauc status mark-active <slot>
...
```

Where `<slot>` is one of:

| **`<slot>`** | **Source**                |
|--------------|---------------------------|
| `rootfs.0`   | Primary partition         |
| `rootfs.1`   | Secondary partition       |
| `net.0`      | Netboot (where supported) |

**Debug**: By default, the kernel will only output errors to the
console during boot. Optionally, this can be altered such that all
enabled messages are logged.

On systems using _U-Boot_, this can be enabled by running `fw_setenv
DEBUG 1`. To restore the default behavior, run `fw_setenv DEBUG`.

On systems running _GRUB_, this can be enabled by running:

```
root@example:~# grub-editenv /mnt/aux/grub/grubenv set DEBUG=1
```

To restore the default behavior, run:

```
root@example:~# grub-editenv /mnt/aux/grub/grubenv unset DEBUG
```

### U-Boot

Used on _aarch64_ based systems.  It is able to verify both the
_integrity_ and _authenticity_ of an Infix image.  As such, it can be
used as a part of a _Secure Boot_ chain, given that the preceding
links are able to do the same.

Supports booting Infix from a block device using the [Disk
Image](#disk-image) layout. Currently, Virtio and MMC disks are
supported.

An [FIT Framed Squash Image](#fit-framed-squash-image) can be used to
boot Infix over the network.  DHCP is used to configure the network
and TFTP to transfer the image to the system's RAM.

Access to U-Boot's shell is disabled to prevent side-loading of
malicious software.  To configure the active boot partition, refer to
the [Bootloader Configuration](#configuration) section.

### GRUB

Used on _x86_64_ based systems.  Neither the _integrity_ nor the
_authenticity_ of the Infix image is verified.  It is only intended to
provide a way of booting a [Disk Image](#disk-image), such that a
standard [System Upgrade](#system-upgrade) can be performed on
virtualized instances.

Access to the GRUB shell is not limited in any way, and the boot
partition can be selected interactively at boot using the arrow keys. It
is also possible to permanently configure the default partition from
Infix using the [Bootloader Configuration](#configuration).

## System Boot

After the system firmware (BIOS or and [boot loader](boot.md) start
Linux the following happens.  The various failure modes, e.g., missing
password in VPD, are detailed later in this section.

![System boot flowchart](img/fail-secure.svg)

1. Before mounting `/cfg` and `/var` partitions, hosting read-writable
   data like `startup-config` and container images, the system first
   checks if a factory reset has been requested by the user, if so it
   wipes the contents of these partitions
1. Linux boots with a device tree which is used for detecting generic
   make and model of the device, e.g., number of interfaces.  It may
   also reference an EEPROM with [Vital Product Data](vpd.md).  That is
   where the base MAC address and per-device password hash is stored.
   (Generic builds use the same MAC address and password)
1. On every boot the system's `factory-config` and `failure-config` are
   generated from the YANG[^2] models of the current firmware version.
   This ensures that a factory reset device can always boot, and that
   there is a working fail safe, or rather *fail secure*, mode
1. On first power-on, and after a factory reset, the system does not
   have a `startup-config`, in which case `factory-config` is copied
   to `startup-config` -- if a per-product specific version exists it
   is preferred over the generated one
1. Provided the integrity of the `startup-config` is OK, a system
   service loads and activates the configuration

### Failure Modes

So, what happens if any of the steps above fail?

#### VPD Fail

The per-device password cannot be read, or is corrupt, so the system
`factory-config` and `failure-config` are not generated:

1. First boot, or after factory reset: `startup-config` cannot be
   created or loaded, and `failure-config` cannot be loaded.  The
   system ends up in an unrecoverable state, i.e., **RMA[^3] Mode**
1. The system has booted (at least) once with correct VPD and password
   and already has a `startup-config`.  Provided the `startup-config`
   is OK (see below), it is loaded and system boots successfully

In both cases, external factory reset modes/button will not help, and
in the second case will cause the device to fail on the next boot.

> [!NOTE]
> The second case does not yet have any warning or event that can be
> detected from the outside.  This is planned for a later release.

#### Broken startup-config

If loading `startup-config` fails for some reason, e.g., invalid JSON
syntax, failed validation against the system's YANG model, or a bug in
the system's `confd` service, the *Fail Secure Mode* is triggered and
`failure-config` is loaded (unless VPD Failure, see above).

> [!TIP]
> Please see the [Branding & Releases](branding.md) document for how to
> provide per-product `failure-config`, or `factory-config` to suit your
> product's preferences.

*Fail Secure Mode* is a fail-safe mode provided for debugging the
system.  The default[^4] creates a setup of isolated interfaces with
communication only to the management CPU, SSH and console login using
the device's factory reset password, IP connectivity only using IPv6
link-local, and device discovery protocols: LLDP, mDNS-SD.  The login
and shell prompt are set to `failure-c0-ff-ee`, the last three octets of
the device's base MAC address.

## System Upgrade

Much of the minutiae of software upgrades is delegated to [RAUC][],
which offers lots of benefits out-of-the-box:

- Upgrade Bundles are always signed, such that their authenticity can
  be verified by the running operating system, before the new one is
  installed.
- The bureaucracy of interfacing with different bootloaders, manage
  the boot order, is a simple matter of providing a compatible
  configuration.
- Updates can be sourced from the local filesystem (including external
  media like USB sticks or SD-cards) and from remote servers using FTP
  or HTTP(S).

To initiate a system upgrade from the shell[^1], run:

```
root@example:~# rauc install <file|url>
...
```

Where the file or URL points to a [RAUC Upgrade Bundle](#rauc-upgrade-bundle).

This will upgrade the partition not currently running.  After a
successful upgrade is completed, you can reboot your system, which
will then boot from the newly installed image.  Since the partition
from which you were originally running is now inactive, running the
same upgrade command again will bring both partitions into sync.

## Image Formats

### SquashFS Image

**Canonical Name**: `rootfs.squashfs`

The central read-only filesystem image containing Infix's Linux
kernel, device trees, and root filesystem. All other images bundle
this image, or is dependent on it, in one way or another.

On its own, it can be used as an [initrd][] to efficiently boot a
virtual instance of Infix.

### FIT Framed Squash Image

**Canonical Name**: `rootfs.itb`

As the name suggests, this is essentially the [Squash FS
Image](#squashfs-image) with a _Flattened Image Tree_ ([FIT][])
header.  Being a native format to U-Boot, using this framing allows us
to verify the integrity and authenticity of the SquashFS image using
standard U-Boot primitives.

In contrast to most FIT images, the kernel and device trees are not
stored as separate binaries in the image tree.  Instead, Infix follows
the standard Linux layout where the kernel and related files are
stored in the `/boot` directory of the filesystem.

On disk, this image is then stored broken up into its two components;
the _FIT header_ (`rootfs.itbh`) and the SquashFS image.  The header
is stored on the [Auxiliary Data](#aux-auxiliary-data) partition of
the [Disk Image](#disk-image), while the SquashFS image is stored in
one of the [Root Filesystem](#primarysecondary-root-filesystems)
partitions.

When the system boots, U-Boot will concatenate the two parts to
validate the SquashFS's contents. This path was chosen because:

- Having a separate raw SquashFS means Linux can directly mount it as
  the root filesystem.

- It decouples Infix from U-Boot.  If a better way of validating our
  image is introduced, we can switch to it without major changes to
  Infix's boot process, as we can still use a regular SquashFS as the
  root filesystem.

- It lets us use standard interfaces to boot Linux, like SYSLINUX.  It
  also plays well with traditional bootloaders, like GRUB.

In its full form, it can be used to netboot Infix, as it contains all
the information needed by U-Boot in a single file.

### RAUC Upgrade Bundle

**Canonical Name**: `infix-${ARCH}.pkg`

Itself a SquashFS image, this bundle (sometimes referred to package)
contains the Infix [SquashFS Image](#squashfs-image) along with the
header of the [FIT Framed Squash Image](#fit-framed-squash-image), and
some supporting files to let [RAUC][] know how install it on the target
system.

When performing a [System Upgrade](#system-upgrade), this is the format
to use.

### Disk Image

**Canonical Name**: `disk.img`

Infix runs from a block device (e.g. eMMC or virtio disk) with the
following layout. The disk is expected to use the GPT partitioning
scheme. Partitions marked with an asterisk are optional.

```
.-----------.
| GPT Table |
:-----------:
|    boot*  |
:-----------:
|    aux    |
:-----------:
|           |
|  primary  |
|           |
:-----------:
|           |
| secondary |
|           |
:-----------:
|    cfg    |
:-----------:
|           |
|    var*   |
|           |
'-----------'
```

#### `boot` - Bootloader

| **Parameter** | **Value**                               |
|---------------|-----------------------------------------|
| Required      | No                                      |
| Size          | 4 MiB                                   |
| Format        | Raw binary, as dictated by the hardware |

Optional partition containing the system's bootloader. May also reside
in a separate storage device, e.g. a serial FLASH.

On x86_64, this partition holds the EFI system partition, containing
the GRUB bootloader.

#### `aux` - Auxiliary Data

| **Parameter** | **Value**       |
|---------------|-----------------|
| Required      | Yes             |
| Size          | 4 MiB           |
| Format        | EXT4 filesystem |

Holds information that is shared between Infix and its bootloader,
such as image signatures required to validate the chain of trust,
bootloader configuration etc.

Typical layout when using U-Boot bootloader:

```
/
├ primary.itbh
├ secondary.itbh
└ uboot.env
```

During boot, an ITB header along with the corresponding root
filesystem image are concatenated in memory, by U-Boot, to form a
valid FIT image that is used to verify its integrity and origin before
any files are extracted from it.

Note that the bootloader's primary environment is bundled in the
binary - `uboot.env` is only used to import a few settings that is
required to configure the boot order.

#### `primary`/`secondary` - Root Filesystems

| **Parameter** | **Value**         |
|---------------|-------------------|
| Required      | Yes               |
| Size          | >= 256 MiB        |
| Format        | Squash filesystem |

Holds the [SquashFS Image](#squashfs-image). Two copies exist so that
an incomplete upgrade does not brick the system, and to allow fast
rollbacks when upgrading to a new version.

#### `cfg` - Configuration Data

| **Parameter** | **Value**       |
|---------------|-----------------|
| Required      | Yes             |
| Size          | >= 16 MiB       |
| Format        | EXT4 filesystem |

Non-volatile storage of the system configuration and user data.
Concretely, user data is everything stored under `/root` and `/home`.

#### `var` - Variable Data

| **Parameter** | **Value**       |
|---------------|-----------------|
| Required      | No              |
| Size          | >= 16 MiB       |
| Format        | EXT4 filesystem |

Persistent storage for everything under `/var`. This is maintained as
a separate filesystem from the data in `cfg`, because while the system
can funtion reasonably well without a persistent `/var`, loosing
`/cfg` or `/etc` is much more difficult.

If `var` is not available, Infix will still persist `/var/lib` using
`cfg` as the backing storage.

[^1]: See [Upgrade & Boot Order](upgrade.md) for more information.
[^2]: YANG is a modeling language from IETF, replacing that used for
    SNMP (MIB), used to describe the subsystems and properties of
    the system.
[^3]: Return Merchandise Authorization (RMA), i.e., broken beyond repair
    by end-user and eligible for return to manufacturer.
[^4]: Customer specific builds can define their own `failure-config`.
    It may be the same as `factory-config`, with the hostname set to
    `failure`, or a dedicated configuration that isolates interfaces, or
    even disables ports, to ensure that the device does not cause any
    security problems on the network.  E.g., start forwarding traffic
    between previously isolated VLANs.

[2]:      netboot.md
[FIT]:    https://u-boot.readthedocs.io/en/latest/usage/fit.html
[RAUC]:   https://rauc.io
[initrd]: https://docs.kernel.org/admin-guide/initrd.html