confd: fix annoying warning in log

This fixes the annoying libyang warning after commit da29771.

    confd[3375]: libyang[0]: Invalid argument ctx_node (lyd_find_xpath()).

This happens when the diff is used in the wrong event when it is NULL.

Signed-off-by: Joachim Wiberg <troglobit@gmail.com>

.github/CHECKLIST.md

@@ -3,39 +3,41 @@ Checklists for Pull Requests and Releases
 
 Maintainer checklists for reviewing pull requests and doing releases.
 
+
 Pull Requests
 -------------
 
-- If applicable, is there a readable ChangeLog entry?
+ - If applicable, is there a readable ChangeLog entry?
-- If any LICENSE file has been updated, has the `.hash` file been updated?
+ - If any LICENSE file has been updated, has the `.hash` file been updated?
-- If any change to a Finit `.svc` file, does any run/task linger?  
+ - If any change to a Finit `.svc` file, does any run/task linger?  
-  I.e., is there a runlevel and/or condition defined to prevent them
+   I.e., is there a runlevel and/or condition defined to prevent them
-  from running outside of their intended runlevel?
+   from running outside of their intended runlevel?
-- If any change to grub or qemu/qeneth setup, has it been tested in GNS3?
+ - If any change to grub or qemu/qeneth setup, has it been tested in GNS3?
-  - If any change to u-boot/buildroot, has it been tested with `<booloader>_defconfig`
+   - If any change to u-boot/buildroot, has it been tested with `<booloader>_defconfig`
-- If any change to logging, have the resulting logs been audited?
+ - If any change to logging, have the resulting logs been audited?
-  - Check for duplicate entries, misspellings
+   - Check for duplicate entries, misspellings
-  - Check for sneaky severity changes, e.g., error vs note, error vs warning
+   - Check for sneaky severity changes, e.g., error vs note, error vs warning
-- If new subsystem, or major changes to a subsystem, have the docs been updated?
+ - If new subsystem, or major changes to a subsystem, have the docs been updated?
-- If change to mDNS, has it been tested with netbrowse?
+ - If change to mDNS, has it been tested with netbrowse?
-- If change to `_defconfig`, verify `local.mk` and sync with other archs
+ - If change to `_defconfig`, verify `local.mk` and sync with other archs
-  - Test manually as well, e.g., CLI changes do not have ha regression tests
+   - Test manually as well, e.g., CLI changes do not have ha regression tests
-  - Build from distclean, or use artifacts built by build servers, for manual tests
+   - Build from distclean, or use artifacts built by build servers, for manual tests
+
 
 Releases
 --------
 
 Recommended checkpoints, use at your own discretion:
 
-- Make at least one -betaN release to verify the GitHub workflow well in time release day
+ - Make at least one -betaN release to verify the GitHub workflow well in time release day
-  - Stuff happens, remember kernelkit/infix#735
+   - Stuff happens, remember kernelkit/infix#735
-- Make at least one -rcN to flush out any issues in customer repos
+ - Make at least one -rcN to flush out any issues in customer repos
-  - Easy to forget adaptations/hacks in customer repos -- may need Infix change/support
+   - Easy to forget adaptations/hacks in customer repos -- may need Infix change/support
-- Verify release artifacts (checksums, completeness, no corrupted files)
+ - Verify release artifacts (checksums, completeness, no corrupted files)
-- Test on actual hardware for at least one architecture
+ - Test on actual hardware for at least one architecture
-- Review ChangeLog for completeness
+ - Review ChangeLog for completeness
-- Check for release-blocking issues
+ - Check for release-blocking issues
-- Verify generated GNS3 appliance, no marketplace update on -rc builds
+ - Verify generated GNS3 appliance, no marketplace update on -rc builds
-- Ensure the markdown link for the release diff is updated
+ - Ensure the markdown link for the release diff is updated
-- Ensure subrepos are tagged (can be automated, see kernelkit/infix#393)
+ - Ensure subrepos are tagged (can be automated, see kernelkit/infix#393)
-- Sync tags for all repo. sync activities
+ - Sync tags for all repo. sync activities

.github/CONTRIBUTING.md

@@ -9,15 +9,15 @@ forms of collaboration as well.  [Let's talk!][support] :handshake:
 
 If you are unsure how to start implementing an idea or fix:
 
-- :bug: open an issue, there are human friendly templates for _bugs_
+ - :bug: open an issue, there are human friendly templates for _bugs_
-  and _feature requests_ at <https://github.com/kernelkit/infix/issues>
+   and _feature requests_ at <https://github.com/kernelkit/infix/issues>
-- :speech_balloon: use the [Q&A Forum][discuss]
+ - :speech_balloon: use the [Q&A Forum][discuss]
-- :technologist: The [Developer's Guide][devguide] is also a useful start
+ - :technologist: The [Developer's Guide][devguide] is also a useful start
 
-> [!IMPORTANT]
+> _Talking about code and problems first is often the best way to get
-> Talking about code and problems first is often the best way to get
 > started before submitting a pull request.  We have found it always
-> saves time, yours and ours.
+> saves time, yours and ours._
+
 
 :sparkles: General Guidelines
 -----------------------------
@@ -27,20 +27,21 @@ version the change is made against, what it does, and, more importantly
 *why* -- from your perspective, why is it a bug, why does the code need
 changing in this way.  Start with why.
 
-- :bug: Bug reports need metadata like Infix version or commit hash
+ - :bug: Bug reports need metadata like Infix version or commit hash
-- :adhesive_bandage: Bug fixes also need version, and (preferably) a
+ - :adhesive_bandage: Bug fixes also need version, and (preferably) a
-  corresponding issue number for the ChangeLog
+   corresponding issue number for the ChangeLog
-- :new: New features, you need to get approval of the YANG model first!  
+ - :new: New features, you need to get approval of the YANG model first!  
-  :speech_balloon: Please use the [Forum][discuss], e.g., category:
+   :speech_balloon: Please use the [Forum][discuss], e.g., category:
-  *Ideas*, or open a :pray: feature request issue
+   *Ideas*, or open a :pray: feature request issue
-- :white_check_mark: New features also need new regression tests, this
+ - :white_check_mark: New features also need new regression tests, this
-  can be basic tests or more complex use-case tests comprising multiple
+   can be basic tests or more complex use-case tests comprising multiple
-  subsystems, see [Testing Changes](#test_tube-testing-changes), below
+   subsystems, see [Testing Changes](#test_tube-testing-changes), below
 
 Please take care to ensure you follow the project coding style and the
 commit message format.  If you follow these recommendations you help
 the maintainers and make it easier for them to include your code.
 
+
 :woman_technologist: Coding Style
 ---------------------------------
 
@@ -50,40 +51,39 @@ and it is expected that you provide a human-readable summary for the
 release notes (ChangeLog) and at least a configuration example in the
 manual for new features.
 
-> [!TIP]
+> **Tip:** consider ["Readme driven development"][RDD] for new features.
-> Consider ["Readme driven development"][RDD] for new features.  It is
+> It is amazing how many flaws in your own bright ideas come to bare
-> amazing how many flaws in your own bright ideas come to bare when you
+> when you suddenly have to explain them to someone else!
-> suddenly have to explain them to someone else!
 
 We expect code contributions for:
 
-- C code in [Linux Coding Style][Linux]
+ - C code in [Linux Coding Style][Linux]
-- Python code should follow [PEP-8][]
+ - Python code should follow [PEP-8][]
 
-> [!IMPORTANT]
 > **However,** always submit code that follows the style of surrounding
 > code!  Legacy takes precedence, and remember, we read code a lot more
 > than write it, so legibility is important.
 
 The ChangeLog deserves a separate mention:
 
-- Releases are listed in reverse chronological order order, so the
+ - Releases are listed in reverse chronological order order, so the
-  latest/next release is at the beginning of the file
+   latest/next release is at the beginning of the file
-- Only *user-facing bugs and features* are detailed, so code refactor,
+ - Only *user-facing bugs and features* are detailed, so code refactor,
-  new tests, etc. are not listed.
+   new tests, etc. are not listed.
-- Add your changes/features to the Changes section
+ - Add your changes/features to the Changes section
-- Add your Fix line in the Fixes section, in numeric order
+ - Add your Fix line in the Fixes section, in numeric order 
-- Changes and fixes without an issue number are listed after all
+ - Changes and fixes without an issue number are listed after all
-  numbered ones
+   numbered ones
-- YANG model changes are documented in their respective model, for
+ - YANG model changes are documented in their respective model, for
-  standard models, e.g., for `ietf-interfaces.yang`, the corresponding
+   standard models, e.g., for `ietf-interfaces.yang`, the corresponding
-  `infix-interfaces.yang` detail augments/deviations as revisions.
+   `infix-interfaces.yang` detail augments/deviations as revisions.
 
 A final note, lines of code are allowed to be longer than 72 characters
 these days, unless you live by PEP-8 (see above).  There is no enforced
 maximum, but the team usually keep it around 100 characters for both C
 and Python.
 
+
 :test_tube: Testing Changes
 ---------------------------
 
@@ -97,8 +97,9 @@ the same pull request.
 
 For help getting started with testing, see the following resources:
 
-- [Developer's Guide][devguide]
+ - [Developer's Guide][devguide]
-- [Regression Testing][testing]
+ - [Regression Testing][testing]
+
 
 :memo: Commit Messages
 ----------------------
@@ -109,135 +110,45 @@ proud of your work and set up a proper GIT identity for your commits:
 
 <img src="../doc/jack.png" width=70 align="right">
 
-```bash
+    $ git config --global user.name "Jacky Linker"
-$ git config --global user.name "Jacky Linker"
+    $ git config --global user.email jacky.linker@example.com
-$ git config --global user.email jacky.linker@example.com
-```
 
 Example commit message from one of many [online guides][cbeams].  Use
 `git commit -s` to automatically add a `Signed-off-by` for proof of
 origin, see [DCO][] for more info.
 
-```text
+    subsystem: brief, but clear and concise summary of changes
-subsystem: brief, but clear and concise summary of changes
+    
+    More detailed explanatory text, if necessary.  Wrap it to about 72
+    characters or so.  In some contexts, the first line is treated as
+    the subject of an email and the rest of the text as the body.  The
+    empty line separating summary from body is critical.  Tools like
+    rebase can get confused if the empty line is missing.
+    
+    Further paragraphs should be separated with empty lines.
+    
+     - Bullet points are okay, too
+    
+     - Typically a hyphen or asterisk is used for the bullet, preceded
+       by a single space, with blank lines in between, but conventions
+       vary here
 
-More detailed explanatory text, if necessary.  Wrap it to about 72
+	If you use an issue tracker, put references to them at the bottom,
-characters or so.  In some contexts, the first line is treated as
+	like this:
-the subject of an email and the rest of the text as the body.  The
-empty line separating summary from body is critical.  Tools like
-rebase can get confused if the empty line is missing.
 
-Further paragraphs should be separated with empty lines.
+	Resolves: #123
+	See also: #456, #789
 
- - Bullet points are okay, too
+    Signed-off-by: Jacky Linker <jacky.linker@example.com>
-
- - Typically a hyphen or asterisk is used for the bullet, preceded
-   by a single space, with blank lines in between, but conventions
-   vary here
-
-If you use an issue tracker, put references to them at the bottom,
-like this:
-
-Resolves: #123
-See also: #456, #789
-
-Signed-off-by: Jacky Linker <jacky.linker@example.com>
-```
 
 This is an example of how to [automatically close][closing] an issue
 when the commit is merged to mainline.  Several keywords are available.
 
-:lock_with_ink_pen: Signing Commits with GPG
----------------------------------------------
-
-To ensure the authenticity and integrity of your contributions, we
-**require** all commits to be signed with GPG.  This cryptographically
-verifies that commits come from a trusted source.
-
-### Generating a GPG Key
-
-If you don't already have a GPG key, generate one:
-
-```bash
-$ gpg --full-generate-key
-```
-
-When prompted, choose:
-- Key type: `RSA and RSA` (default)
-- Key size: `4096` bits (recommended for security)
-- Expiration: `0` (key does not expire)
-- Real name and email: Use the same email as your Git configuration
-
-> [!NOTE]
-> We recommend keys that do not expire for signing commits.  Expiration
-> creates a "usability time bomb" without providing meaningful security
-> benefits for code signing.  See [this article][pgpfan] for details.
-
-### Configuring Git to Sign Commits
-
-First, find your GPG key ID:
-
-```bash
-$ gpg --list-secret-keys --keyid-format=long
-```
-
-Look for the line starting with `sec`, the key ID is the part after the `/`.
-For example, in `sec   rsa4096/ABCD1234EFGH5678`, the key ID is `ABCD1234EFGH5678`.
-
-Configure Git to use your GPG key:
-
-```bash
-$ git config --global user.signingkey ABCD1234EFGH5678
-$ git config --global commit.gpgsign true
-```
-
-The second command enables automatic signing for all commits.  Alternatively,
-you can sign individual commits with `git commit -S`.
-
-### Publishing Your Public Key
-
-To allow others to verify your signatures, publish your public key to a
-keyserver:
-
-```bash
-$ gpg --keyserver hkps://keys.openpgp.org --send-keys ABCD1234EFGH5678
-```
-
-> [!IMPORTANT]
-> The keyserver will send a verification email to the address associated
-> with your key.  You **must** click the link in that email to confirm
-> ownership before your key becomes searchable by email address.
-
-Alternative keyservers you can use:
-- `hkps://keyserver.ubuntu.com`
-- `hkps://pgp.mit.edu`
-
-### Adding Your GPG Key to GitHub
-
-For GitHub to show your commits as "Verified", you need to add your public
-key to your account:
-
-1. Export your public key:
-   ```bash
-   $ gpg --armor --export ABCD1234EFGH5678
-   ```
-
-2. Copy the entire output, including the `-----BEGIN PGP PUBLIC KEY BLOCK-----`
-   and `-----END PGP PUBLIC KEY BLOCK-----` lines.
-
-3. Go to [GitHub Settings → SSH and GPG keys](https://github.com/settings/keys)
-
-4. Click **New GPG key** and paste your public key.
-
-Now your signed commits will display a "Verified" badge on GitHub! :white_check_mark:
-
-For more details, see GitHub's [official documentation on commit signature verification][gpg-verify].
 
 :twisted_rightwards_arrows: Pull Requests
 -----------------------------------------
 
-> [!NOTE]
+> _The git repository is the canonical location for information._
-> _The git repository is the canonical location for all information._
 
 A pull request should preferably address a single issue or change.  This
 may of course include multiple related changes, but what is important to
@@ -256,6 +167,7 @@ Buildroot, consider the pull request message body similar to the cover
 letter for a series of patches -- it's a summary of changes, and it is
 lost when the changes are merged to the mainline branch.
 
+
 :balance_scale: Code of Conduct
 -------------------------------
 
@@ -272,8 +184,6 @@ other contributions that are not aligned to this Code of Conduct."*
 [PEP-8]:    https://peps.python.org/pep-0008/
 [RDD]:      https://tom.preston-werner.com/2010/08/23/readme-driven-development
 [cbeams]:   https://cbea.ms/git-commit/#seven-rules
-[conduct]:    CODE-OF-CONDUCT.md
+[conduct]:  CODE-OF-CONDUCT.md
-[DCO]:        https://developercertificate.org/
+[DCO]:      https://developercertificate.org/
-[closing]:    https://docs.github.com/en/get-started/writing-on-github/working-with-advanced-formatting/using-keywords-in-issues-and-pull-requests
+[closing]:  https://docs.github.com/en/get-started/writing-on-github/working-with-advanced-formatting/using-keywords-in-issues-and-pull-requests
-[gpg-verify]: https://docs.github.com/en/authentication/managing-commit-signature-verification
-[pgpfan]:     https://articles.59.ca/doku.php?id=pgpfan:expire

.github/workflows/build-boot.yml

@@ -17,8 +17,7 @@ jobs:
       matrix:
         defconfig:
           - aarch64_qemu_boot
-          - bpi_r3_sd_boot
+          - bpi_r3_boot
-          - bpi_r3_emmc_boot
           - cn9130_crb_boot
           - fireant_boot
           - nanopi_r2s_boot

.github/workflows/build-image.yml

@@ -1,4 +1,4 @@
-name: Create SD Card & eMMC Images
+name: Create SD Card Images
 
 on:
   workflow_dispatch:
@@ -56,33 +56,21 @@ jobs:
             raspberrypi-rpi64)
               echo "BOOTLOADER=rpi64_boot" >> $GITHUB_ENV
               echo "TARGET=aarch64" >> $GITHUB_ENV
-              echo "BUILD_EMMC=false" >> $GITHUB_ENV
               ;;
             bananapi-bpi-r3)
-              echo "BOOTLOADER_SD=bpi_r3_sd_boot" >> $GITHUB_ENV
+              echo "BOOTLOADER=bpi_r3_boot" >> $GITHUB_ENV
-              echo "BOOTLOADER_EMMC=bpi_r3_emmc_boot" >> $GITHUB_ENV
               echo "TARGET=aarch64" >> $GITHUB_ENV
-              echo "BUILD_EMMC=true" >> $GITHUB_ENV
               ;;
             friendlyarm-nanopi-r2s)
               echo "BOOTLOADER=nanopi_r2s_boot" >> $GITHUB_ENV
               echo "TARGET=aarch64" >> $GITHUB_ENV
-              echo "BUILD_EMMC=false" >> $GITHUB_ENV
               ;;
             *)
               echo "Error: Unknown board ${{ inputs.board }}"
               exit 1
               ;;
           esac
-          echo "Target: $TARGET for board: ${{ inputs.board }}"
+          echo "Using bootloader: $BOOTLOADER and target: $TARGET for board: ${{ inputs.board }}"
-          if [ "$BUILD_EMMC" = "true" ]; then
-            echo "Building both SD and eMMC images"
-            echo "SD Bootloader: $BOOTLOADER_SD"
-            echo "eMMC Bootloader: $BOOTLOADER_EMMC"
-          else
-            echo "Building SD image only"
-            echo "Bootloader: $BOOTLOADER"
-          fi
 
       - name: Download bootloader artifacts
         if: ${{ !inputs.use_latest_release }}
@@ -91,41 +79,16 @@ jobs:
           gh run list --workflow=build-boot.yml --branch=main --limit=1 --status=success --json databaseId --jq '.[0].databaseId' > latest_boot_run_id
           BOOT_RUN_ID=$(cat latest_boot_run_id)
 
-          if [ "$BUILD_EMMC" = "true" ]; then
+          gh run download ${BOOT_RUN_ID} --name artifact-${BOOTLOADER} --dir temp_bootloader/
-            # Download both SD and eMMC bootloaders for boards that support both
-            echo "Downloading SD bootloader: ${BOOTLOADER_SD}"
-            gh run download ${BOOT_RUN_ID} --name artifact-${BOOTLOADER_SD} --dir temp_bootloader_sd/
-            mkdir -p output_sd/images
-            cd temp_bootloader_sd/
-            tar -xzf *.tar.gz --strip-components=1 -C ../output_sd/images/
-            cd ../
-            rm -rf temp_bootloader_sd/
 
-            echo "Downloading eMMC bootloader: ${BOOTLOADER_EMMC}"
+          # Extract bootloader directly to output/images
-            gh run download ${BOOT_RUN_ID} --name artifact-${BOOTLOADER_EMMC} --dir temp_bootloader_emmc/
+          cd temp_bootloader/
-            mkdir -p output_emmc/images
+          tar -xzf *.tar.gz --strip-components=1 -C ../output/images/
-            cd temp_bootloader_emmc/
+          cd ../
-            tar -xzf *.tar.gz --strip-components=1 -C ../output_emmc/images/
+          rm -rf temp_bootloader/
-            cd ../
-            rm -rf temp_bootloader_emmc/
 
-            echo "SD bootloader files:"
+          echo "Bootloader files extracted to output/images:"
-            ls -la output_sd/images/
+          ls -la output/images/
-            echo "eMMC bootloader files:"
-            ls -la output_emmc/images/
-          else
-            # Single bootloader for boards that only support SD
-            gh run download ${BOOT_RUN_ID} --name artifact-${BOOTLOADER} --dir temp_bootloader/
-
-            # Extract bootloader directly to output/images
-            cd temp_bootloader/
-            tar -xzf *.tar.gz --strip-components=1 -C ../output/images/
-            cd ../
-            rm -rf temp_bootloader/
-
-            echo "Bootloader files extracted to output/images:"
-            ls -la output/images/
-          fi
         env:
           GH_TOKEN: ${{ secrets.GITHUB_TOKEN }}
 
@@ -136,193 +99,90 @@ jobs:
           gh run list --workflow=164295764 --branch=main --limit=1 --status=success --json databaseId --jq '.[0].databaseId' > latest_infix_run_id
           INFIX_RUN_ID=$(cat latest_infix_run_id)
 
-          if [ "$BUILD_EMMC" = "true" ]; then
+          gh run download ${INFIX_RUN_ID} --name artifact-${TARGET} --dir temp_infix/
-            # Copy Infix artifacts to both SD and eMMC output directories
-            gh run download ${INFIX_RUN_ID} --name artifact-${TARGET} --dir temp_infix/
 
-            cd temp_infix/
+          # Extract Infix directly to output/images
-            tar -xzf *.tar.gz --strip-components=1 -C ../output_sd/images/
+          cd temp_infix/
-            tar -xzf *.tar.gz --strip-components=1 -C ../output_emmc/images/
+          tar -xzf *.tar.gz --strip-components=1 -C ../output/images/
-            cd ../
+          cd ../
-            rm -rf temp_infix/
+          rm -rf temp_infix/
 
-            echo "Infix files extracted to output_sd/images:"
+          echo "Infix files extracted to output/images:"
-            ls -la output_sd/images/
+          ls -la output/images/
-            echo "Infix files extracted to output_emmc/images:"
-            ls -la output_emmc/images/
-          else
-            # Single output directory for SD-only boards
-            gh run download ${INFIX_RUN_ID} --name artifact-${TARGET} --dir temp_infix/
-
-            # Extract Infix directly to output/images
-            cd temp_infix/
-            tar -xzf *.tar.gz --strip-components=1 -C ../output/images/
-            cd ../
-            rm -rf temp_infix/
-
-            echo "Infix files extracted to output/images:"
-            ls -la output/images/
-          fi
         env:
           GH_TOKEN: ${{ secrets.GITHUB_TOKEN }}
 
       - name: Download from latest releases
         if: ${{ inputs.use_latest_release }}
         run: |
-          if [ "$BUILD_EMMC" = "true" ]; then
+          # Download latest bootloader release
-            # Download both SD and eMMC bootloaders
+          gh release download latest-boot --pattern "*${BOOTLOADER}*" --dir temp_bootloader/
-            gh release download latest-boot --pattern "*${BOOTLOADER_SD}*" --dir temp_bootloader_sd/
+          cd temp_bootloader/
-            mkdir -p output_sd/images
+          tar -xzf *.tar.gz --strip-components=1 -C ../output/images/
-            cd temp_bootloader_sd/
+          cd ../
-            tar -xzf *.tar.gz --strip-components=1 -C ../output_sd/images/
+          rm -rf temp_bootloader/
-            cd ../
-            rm -rf temp_bootloader_sd/
 
-            gh release download latest-boot --pattern "*${BOOTLOADER_EMMC}*" --dir temp_bootloader_emmc/
+          # Download latest Infix release
-            mkdir -p output_emmc/images
+          gh release download latest --pattern "*${TARGET}*" --dir temp_infix/
-            cd temp_bootloader_emmc/
+          cd temp_infix/
-            tar -xzf *.tar.gz --strip-components=1 -C ../output_emmc/images/
+          tar -xzf *.tar.gz --strip-components=1 -C ../output/images/
-            cd ../
+          cd ../
-            rm -rf temp_bootloader_emmc/
+          rm -rf temp_infix/
 
-            # Download Infix once and extract to both directories
+          echo "All files extracted to output/images:"
-            gh release download latest --pattern "*${TARGET}*" --dir temp_infix/
+          ls -la output/images/
-            cd temp_infix/
-            tar -xzf *.tar.gz --strip-components=1 -C ../output_sd/images/
-            tar -xzf *.tar.gz --strip-components=1 -C ../output_emmc/images/
-            cd ../
-            rm -rf temp_infix/
-
-            echo "SD files extracted to output_sd/images:"
-            ls -la output_sd/images/
-            echo "eMMC files extracted to output_emmc/images:"
-            ls -la output_emmc/images/
-          else
-            # Download latest bootloader release
-            gh release download latest-boot --pattern "*${BOOTLOADER}*" --dir temp_bootloader/
-            cd temp_bootloader/
-            tar -xzf *.tar.gz --strip-components=1 -C ../output/images/
-            cd ../
-            rm -rf temp_bootloader/
-
-            # Download latest Infix release
-            gh release download latest --pattern "*${TARGET}*" --dir temp_infix/
-            cd temp_infix/
-            tar -xzf *.tar.gz --strip-components=1 -C ../output/images/
-            cd ../
-            rm -rf temp_infix/
-
-            echo "All files extracted to output/images:"
-            ls -la output/images/
-          fi
         env:
           GH_TOKEN: ${{ secrets.GITHUB_TOKEN }}
 
       - name: Verify extracted files
         run: |
-          if [ "$BUILD_EMMC" = "true" ]; then
+          echo "Files available for mkimage.sh:"
-            echo "Files available for SD image:"
+          ls -la output/images/
-            ls -la output_sd/images/
+          echo ""
-            echo ""
+          echo "File types:"
-            echo "Files available for eMMC image:"
+          file output/images/* || true
-            ls -la output_emmc/images/
-          else
-            echo "Files available for mkimage.sh:"
-            ls -la output/images/
-            echo ""
-            echo "File types:"
-            file output/images/* || true
-          fi
 
       - name: Create SD card image
         run: |
-          if [ "$BUILD_EMMC" = "true" ]; then
+          export BINARIES_DIR=$PWD/output/images
-            export BINARIES_DIR=$PWD/output_sd/images
-            export BUILD_DIR=$PWD/build
-            export BR2_EXTERNAL_INFIX_PATH=$PWD
-            export RELEASE=""
-            export INFIX_ID="infix"
-            ./utils/mkimage.sh -t sdcard ${{ inputs.board }}
-          else
-            export BINARIES_DIR=$PWD/output/images
-            export BUILD_DIR=$PWD/build
-            export BR2_EXTERNAL_INFIX_PATH=$PWD
-            export RELEASE=""
-            export INFIX_ID="infix"
-            ./utils/mkimage.sh ${{ inputs.board }}
-          fi
-
-      - name: Create eMMC image
-        if: ${{ env.BUILD_EMMC == 'true' }}
-        run: |
-          export BINARIES_DIR=$PWD/output_emmc/images
           export BUILD_DIR=$PWD/build
           export BR2_EXTERNAL_INFIX_PATH=$PWD
           export RELEASE=""
           export INFIX_ID="infix"
-          ./utils/mkimage.sh -t emmc ${{ inputs.board }}
+          ./utils/mkimage.sh ${{ inputs.board }}
 
-      - name: Verify created images
+      - name: Verify created image
         run: |
-          if [ "$BUILD_EMMC" = "true" ]; then
+          echo "Contents of output/images after mkimage.sh:"
-            echo "SD card image:"
+          ls -lh output/images/
-            ls -lh output_sd/images/*-sdcard.img* 2>/dev/null || true
-            if ls output_sd/images/*-sdcard.img 1> /dev/null 2>&1; then
-              for img in output_sd/images/*-sdcard.img; do
-                echo "- $(basename $img)"
-                file "$img"
-                fdisk -l "$img" 2>/dev/null | head -20
-              done
-            fi
 
-            echo ""
+          # Look for SD card image with pattern: *-sdcard.img
-            echo "eMMC image:"
+          if ls output/images/*-sdcard.img 1> /dev/null 2>&1; then
-            ls -lh output_emmc/images/*-emmc.img* 2>/dev/null || true
+            echo "Found SD card image(s):"
-            if ls output_emmc/images/*-emmc.img 1> /dev/null 2>&1; then
+            for img in output/images/*-sdcard.img; do
-              for img in output_emmc/images/*-emmc.img; do
+              echo "- $(basename $img)"
-                echo "- $(basename $img)"
+              file "$img"
-                file "$img"
+              fdisk -l "$img" 2>/dev/null || true
-                fdisk -l "$img" 2>/dev/null | head -20
+            done
-              done
-            fi
-
-            # Copy both images to output/images for artifact upload
-            mkdir -p output/images
-            cp output_sd/images/*-sdcard.img* output/images/ 2>/dev/null || true
-            cp output_emmc/images/*-emmc.img* output/images/ 2>/dev/null || true
           else
-            echo "Contents of output/images after mkimage.sh:"
+            echo "No SD card image found matching pattern: *-sdcard.img"
-            ls -lh output/images/
+            echo "Available files:"
-
+            ls -la output/images/
-            # Look for SD card image with pattern: *-sdcard.img
+            exit 1
-            if ls output/images/*-sdcard.img 1> /dev/null 2>&1; then
-              echo "Found SD card image(s):"
-              for img in output/images/*-sdcard.img; do
-                echo "- $(basename $img)"
-                file "$img"
-                fdisk -l "$img" 2>/dev/null || true
-              done
-            else
-              echo "No SD card image found matching pattern: *-sdcard.img"
-              echo "Available files:"
-              ls -la output/images/
-              exit 1
-            fi
           fi
 
-      - name: Upload images as artifacts
+      - name: Upload SD card image
         uses: actions/upload-artifact@v4
         with:
-          name: images-${{ inputs.board }}
+          name: sdcard-image-${{ inputs.board }}-${{ env.BOOTLOADER }}
           path: |
             output/images/*-sdcard.img*
-            output/images/*-emmc.img*
           retention-days: 30
 
       - name: Create checksums
         run: |
           cd output/images/
-          for file in *-sdcard.img *-emmc.img; do
+          for file in *-sdcard.img; do
             if [ -f "$file" ]; then
               sha256sum "$file" > "$file.sha256"
             fi
@@ -338,28 +198,11 @@ jobs:
           prerelease: true
           tag: "latest-boot"
           token: ${{ secrets.GITHUB_TOKEN }}
-          artifacts: "output/images/*-sdcard.img*,output/images/*-emmc.img*"
+          artifacts: "output/images/*-sdcard.img*"
 
       - name: Generate summary
         run: |
-          if [ "$BUILD_EMMC" = "true" ]; then
+          cat <<EOF >> $GITHUB_STEP_SUMMARY
-            cat <<EOF >> $GITHUB_STEP_SUMMARY
-          # SD Card & eMMC Image Build Complete! 🚀
-
-          **Board:** ${{ inputs.board }}
-          **Target:** ${{ env.TARGET }}
-          **SD Bootloader:** ${{ env.BOOTLOADER_SD }}
-          **eMMC Bootloader:** ${{ env.BOOTLOADER_EMMC }}
-          **Artifact Source:** ${{ inputs.use_latest_release && 'Latest Release' || 'Latest Workflow Run' }}
-
-          ## Created Images
-          $(find output/images/ -name "*.img" -o -name "*.img.bmap" | xargs ls -lh 2>/dev/null | awk '{print "- " $9 " (" $5 ")"}' || echo "- No images found")
-
-          ## Download
-          Both SD card and eMMC images are available as workflow artifacts above and in the latest-boot release.
-          EOF
-          else
-            cat <<EOF >> $GITHUB_STEP_SUMMARY
           # SD Card Image Build Complete! 🚀
 
           **Board:** ${{ inputs.board }}
@@ -368,9 +211,8 @@ jobs:
           **Artifact Source:** ${{ inputs.use_latest_release && 'Latest Release' || 'Latest Workflow Run' }}
 
           ## Created Images
-          $(find output/images/ -name "*.img" -o -name "*.img.bmap" | xargs ls -lh 2>/dev/null | awk '{print "- " $9 " (" $5 ")"}' || echo "- No images found")
+          $(find output/images/ -name "*.img*" -o -name "*.qcow2" -o -name "*.raw" | xargs ls -lh 2>/dev/null | sed 's/^/- /' || echo "- No images found")
 
           ## Download
           The SD card image is available as a workflow artifact above.
           EOF
-          fi

.github/workflows/build-release.yml

@@ -1,6 +1,3 @@
-# Needed for make pkg-stats
-# sudo apt install python3-aiohttp
----
 name: Build Release
 
 on:
@@ -78,12 +75,7 @@ jobs:
 
       - name: Generate SBOM from Build
         run: |
-          # Generate manifest files in CSV format for CycloneDX
           make legal-info
-          # Generate cpe.json for CycloneDX
-          make -s show-info > output/cpe.json
-          # Generate pkg-stats.{json,html} for humans
-          make pkg-stats
 
       - name: Build test specification
         run: |
@@ -92,22 +84,13 @@ jobs:
       - name: Prepare Artifacts
         run: |
           cd output/
-
-          # Collect relevant files for SBOM and CPE info. for more info, see:
-          # https://github.com/CycloneDX/cyclonedx-buildroot
-          mkdir               images/sbom
-          mv pkg-stats.*      images/sbom/
-          mv cpe.json         images/sbom/
-          mv legal-info/*.csv images/sbom/
-
-          # Remove rootfs.squashfs from release (can be extracted from rootfs.itb)
-          # Saves ~131MB per architecture. See issue #858
-          rm -f images/rootfs.squashfs
-
           mv images ${{ steps.vars.outputs.dir }}
           ln -s ${{ steps.vars.outputs.dir }} images
           tar cfz ${{ steps.vars.outputs.tgz }} ${{ steps.vars.outputs.dir }}
 
+          mv legal-info legal-info-${{ matrix.target }}-${{ steps.vars.outputs.ver }}
+          tar cfz legal-info-${{ matrix.target }}-${{ steps.vars.outputs.ver }}.tar.gz legal-info-${{ matrix.target }}-${{ steps.vars.outputs.ver }}
+
       - uses: actions/upload-artifact@v4
         with:
           name: artifact-${{ matrix.target }}

.github/workflows/build.yml

@@ -19,10 +19,6 @@ on:
         description: 'Repo to checkout (for spin overrides)'
         default: kernelkit/infix
         type: string
-      infix_branch:
-        description: 'Branch/tag/commit to checkout (for spin overrides)'
-        default: ''
-        type: string
 
   workflow_call:
     inputs:
@@ -36,30 +32,15 @@ on:
         required: false
         type: string
         default: kernelkit/infix
-      infix_branch:
-        required: false
-        type: string
-        default: ''
-        description: 'Branch/tag/commit to checkout (for spin overrides). Defaults to github.ref if not specified'
       parallel:
         required: false
         type: boolean
         default: true
-      pre_build_script:
-        required: false
-        type: string
-        default: ''
-        description: 'Optional script to run after checkout (for spin customization)'
-    secrets:
-      CHECKOUT_TOKEN:
-        required: false
-        description: 'Token for cross-repository access'
 
 env:
   NAME: ${{ github.event_name == 'workflow_dispatch' && github.event.inputs.name || inputs.name }}
   TARGET: ${{ github.event_name == 'workflow_dispatch' && github.event.inputs.target || inputs.target }}
   INFIX_REPO: ${{ github.event_name == 'workflow_dispatch' && github.event.inputs.infix_repo || inputs.infix_repo }}
-  INFIX_BRANCH: ${{ github.event_name == 'workflow_dispatch' && github.event.inputs.infix_branch || inputs.infix_branch }}
 
 jobs:
   build:
@@ -92,20 +73,10 @@ jobs:
         uses: actions/checkout@v4
         with:
           repository: ${{ env.INFIX_REPO }}
-          ref: ${{ env.INFIX_BRANCH != '' && env.INFIX_BRANCH || github.ref }}
+          ref: ${{ github.ref }}
           clean: true
           fetch-depth: 0
           submodules: recursive
-          token: ${{ secrets.CHECKOUT_TOKEN || github.token }}
-
-      - name: Run pre-build script
-        if: ${{ inputs.pre_build_script != '' }}
-        run: |
-          cat > ./pre-build.sh << 'EOF'
-          ${{ inputs.pre_build_script }}
-          EOF
-          chmod +x ./pre-build.sh
-          bash ./pre-build.sh
 
       - name: Set Build Variables
         id: vars

.github/workflows/check-kernel-release.yml

@@ -1,13 +1,10 @@
 name: Check Kernel 6.12 Release
 
 on:
-  schedule:
+  workflow_dispatch: # Allow manual triggering
-    - cron: '0 3 * * *'
-  workflow_dispatch:
 
 jobs:
   check-kernel:
-    if: github.repository == 'kernelkit/infix'
     runs-on: ubuntu-latest
 
     steps:
@@ -17,6 +14,14 @@ jobs:
           fetch-depth: 0
           token: ${{ secrets.KERNEL_UPDATE_TOKEN }}
 
+      - name: Check out linux repository
+        uses: actions/checkout@v4
+        with:
+          repository: kernelkit/linux
+          path: linux
+          fetch-depth: 0
+          token: ${{ secrets.KERNEL_UPDATE_TOKEN }}
+
       - name: Fetch kernel.org and check for 6.12 release
         id: check
         run: |
@@ -32,52 +37,22 @@ jobs:
           echo "current_version=$CURRENT_VERSION" >> $GITHUB_OUTPUT
           echo "Current 6.12 kernel version: $CURRENT_VERSION"
 
-          # Get the version from infix defconfig
+          # Get the latest tag from our linux tree
-          INFIX_VERSION=$(grep 'BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE=' configs/aarch64_defconfig | cut -d'"' -f2)
+          cd linux
+          git fetch origin
+          LATEST_TAG=$(git tag -l "v6.12.*" | sort -V | tail -n1 | sed 's/^v//')
+          cd ..
 
-          echo "infix_version=$INFIX_VERSION" >> $GITHUB_OUTPUT
+          echo "latest_tag=$LATEST_TAG" >> $GITHUB_OUTPUT
-          echo "Infix kernel version: $INFIX_VERSION"
+          echo "Latest tag in our tree: $LATEST_TAG"
 
-          if [ "$CURRENT_VERSION" != "$INFIX_VERSION" ]; then
+          if [ "$CURRENT_VERSION" != "$LATEST_TAG" ]; then
-            # Check if there's already an open PR for this version
+            echo "new_release=true" >> $GITHUB_OUTPUT
-            PR_EXISTS=$(gh pr list --state open --search "Upgrade to kernel $CURRENT_VERSION in:title" --json number --jq 'length')
+            echo "🎉 New 6.12 kernel released: $CURRENT_VERSION (our version: $LATEST_TAG)"
-
-            if [ "$PR_EXISTS" -gt 0 ]; then
-              echo "new_release=false" >> $GITHUB_OUTPUT
-              echo "PR already exists for kernel $CURRENT_VERSION, skipping"
-            else
-              echo "new_release=true" >> $GITHUB_OUTPUT
-              echo "🎉 New 6.12 kernel released: $CURRENT_VERSION (infix version: $INFIX_VERSION)"
-            fi
           else
             echo "new_release=false" >> $GITHUB_OUTPUT
             echo "No change - still at $CURRENT_VERSION"
           fi
-        env:
-          GH_TOKEN: ${{ secrets.KERNEL_UPDATE_TOKEN }}
-
-      - name: Generate branch name
-        if: steps.check.outputs.new_release == 'true'
-        id: branch
-        run: |
-          BRANCH_NAME="kernel-upgrade-$(uuidgen | tr '[:upper:]' '[:lower:]')"
-          echo "name=$BRANCH_NAME" >> $GITHUB_OUTPUT
-          echo "Branch name: $BRANCH_NAME"
-
-      - name: Import GPG key
-        if: steps.check.outputs.new_release == 'true'
-        run: |
-          # Import the GPG key
-          echo "${{ secrets.AEL_BOT_GPG_PRIVATE_KEY }}" | gpg --batch --import
-
-          # Get the key ID
-          GPG_KEY_ID=$(gpg --list-secret-keys --keyid-format=long | grep '^sec' | head -1 | awk '{print $2}' | cut -d'/' -f2)
-          echo "GPG_KEY_ID=$GPG_KEY_ID" >> $GITHUB_ENV
-
-          # Configure GPG agent for non-interactive use
-          echo "allow-loopback-pinentry" >> ~/.gnupg/gpg-agent.conf
-          echo "pinentry-mode loopback" >> ~/.gnupg/gpg.conf
-          gpg-connect-agent reloadagent /bye || true
 
       - name: Set up git credentials
         if: steps.check.outputs.new_release == 'true'
@@ -85,8 +60,6 @@ jobs:
           set -e -o pipefail
           git config --global user.email "ael-bot@users.noreply.github.com"
           git config --global user.name "ael-bot"
-          git config --global commit.gpgsign true
-          git config --global user.signingkey ${{ env.GPG_KEY_ID }}
 
           # Configure git to use the token for HTTPS operations
           git config --global url."https://ael-bot:${{ secrets.KERNEL_UPDATE_TOKEN }}@github.com/".insteadOf "git@github.com:"
@@ -96,10 +69,9 @@ jobs:
         if: steps.check.outputs.new_release == 'true'
         env:
           GIT_TERMINAL_PROMPT: 0
-          BRANCH_NAME: ${{ steps.branch.outputs.name }}
         run: |
           set -e -o pipefail
-          ./utils/kernel-upgrade.sh linux "$BRANCH_NAME"
+          ./utils/kernel-upgrade.sh linux
 
       - name: Create pull request
         if: steps.check.outputs.new_release == 'true'
@@ -107,6 +79,7 @@ jobs:
         with:
           github-token: ${{ secrets.KERNEL_UPDATE_TOKEN }}
           script: |
+            // Check if PR already exists
             const { data: pulls } = await github.rest.pulls.list({
               owner: context.repo.owner,
               repo: context.repo.repo,
@@ -119,11 +92,12 @@ jobs:
                 owner: context.repo.owner,
                 repo: context.repo.repo,
                 title: `Upgrade to kernel ${{ steps.check.outputs.current_version }}`,
-                head: '${{ steps.branch.outputs.name }}',
+                head: 'kernel-upgrade',
                 base: 'main',
-                body: `Automated kernel upgrade to version ${{ steps.check.outputs.current_version }}.\n\n**Previous version:** ${{ steps.check.outputs.infix_version }}\n**New version:** ${{ steps.check.outputs.current_version }}\n**Source:** https://www.kernel.org/\n\nThis PR was automatically created by the kernel release monitoring workflow.`
+                body: `Automated kernel upgrade to version ${{ steps.check.outputs.current_version }}.\n\n**Previous version:** ${{ steps.check.outputs.latest_tag }}\n**New version:** ${{ steps.check.outputs.current_version }}\n**Source:** https://www.kernel.org/\n\nThis PR was automatically created by the kernel release monitoring workflow.`
               });
 
+              // Add label
               await github.rest.issues.addLabels({
                 owner: context.repo.owner,
                 repo: context.repo.repo,
@@ -131,6 +105,7 @@ jobs:
                 labels: ['ci:main']
               });
 
+              // Request reviews
               await github.rest.pulls.requestReviewers({
                 owner: context.repo.owner,
                 repo: context.repo.repo,

.github/workflows/coverity.yml

@@ -69,10 +69,10 @@ jobs:
           (cd libite && ./autogen.sh && ./configure && make && sudo make install)
           make dep
 
-      - name: Build applications for Coverity
+      - name: Check applications
         run: |
           export PATH=`pwd`/coverity/bin:$PATH
-          cov-build --dir cov-int make coverity
+          cov-build --dir cov-int make check
 
       - name: Submit results to Coverity Scan
         env:

.github/workflows/release.yml

@@ -75,7 +75,7 @@ jobs:
           if echo $ver | grep -qE 'v[0-9.]+(-alpha|-beta|-rc)[0-9]*'; then
             echo "pre=true"     >> $GITHUB_OUTPUT
             echo "latest=false" >> $GITHUB_OUTPUT
-          elif echo $ver | grep -qE '^v[0-9]+\.[0-9]+(\.0)?$'; then
+          elif echo $ver | grep -qE '^v[0-9.]+\.[0-9.]+(\.[0-9]+)?$'; then
             echo "pre=false"    >> $GITHUB_OUTPUT
             echo "latest=true"  >> $GITHUB_OUTPUT
             echo "cat=Releases" >> $GITHUB_OUTPUT
@@ -117,7 +117,7 @@ jobs:
           prerelease: ${{ steps.rel.outputs.pre }}
           makeLatest: ${{ steps.rel.outputs.latest }}
           discussionCategory: ${{ steps.rel.outputs.cat }}
-          bodyFile: release.md
+          bodyFile:  release.md
           artifacts: "*.tar.gz*,*.qcow2*"
 
       - name: Summary

.github/workflows/test.yml

@@ -8,10 +8,6 @@ on:
         required: false
         default: kernelkit/infix
         type: string
-      infix_branch:
-        description: 'Branch/tag/commit to checkout (for spin overrides)'
-        default: ''
-        type: string
 
   workflow_call:
     inputs:
@@ -25,11 +21,6 @@ on:
         required: false
         type: string
         default: kernelkit/infix
-      infix_branch:
-        required: false
-        type: string
-        default: ''
-        description: 'Branch/tag/commit to checkout (for spin overrides). Defaults to github.ref if not specified'
       ninepm-conf:
         required: false
         type: string
@@ -38,20 +29,10 @@ on:
         required: false
         type: string
         default: 'test'
-      pre_test_script:
-        required: false
-        type: string
-        default: ''
-        description: 'Optional script to run after checkout (for spin customization)'
-    secrets:
-      CHECKOUT_TOKEN:
-        required: false
-        description: 'Token for cross-repository access'
 
 env:
   TARGET: ${{ github.event_name == 'workflow_dispatch' && github.event.inputs.target || inputs.target }}
   INFIX_REPO: ${{ github.event_name == 'workflow_dispatch' && github.event.inputs.infix_repo || inputs.infix_repo }}
-  INFIX_BRANCH: ${{ github.event_name == 'workflow_dispatch' && github.event.inputs.infix_branch || inputs.infix_branch }}
   NINEPM_CONF: ${{ github.event_name == 'workflow_dispatch' && github.event.inputs.ninepm-conf || inputs.ninepm-conf }}
   TEST_PATH: ${{ github.event_name == 'workflow_dispatch' && github.event.inputs.test-path || inputs.test-path }}
 
@@ -74,20 +55,10 @@ jobs:
         uses: actions/checkout@v4
         with:
           repository: ${{ env.INFIX_REPO }}
-          ref: ${{ env.INFIX_BRANCH != '' && env.INFIX_BRANCH || github.ref }}
+          ref: ${{ github.ref }}
           clean: true
           fetch-depth: 0
           submodules: recursive
-          token: ${{ secrets.CHECKOUT_TOKEN || github.token }}
-
-      - name: Run pre-test script
-        if: ${{ inputs.pre_test_script != '' }}
-        run: |
-          cat > ./pre-test.sh << 'EOF'
-          ${{ inputs.pre_test_script }}
-          EOF
-          chmod +x ./pre-test.sh
-          bash ./pre-test.sh
 
       - name: Set Build Variables
         id: vars

.gitignore

@@ -1,5 +1,4 @@
 *~
-.claude
 .gdb_history
 /.backup
 /.ccache

Makefile

@@ -16,7 +16,8 @@ bmake   = $(MAKE) -C buildroot O=$(O) $1
 all: $(config) buildroot/Makefile
 	@+$(call bmake,$@)
 
-check dep coverity:
+check dep:
+	@echo "Starting local check, stage $@ ..."
 	@make -C src $@
 
 $(config):
@@ -32,11 +33,6 @@ $(config):
 legal-info: | buildroot/Makefile
 	$(call bmake,legal-info LINUX_LICENSE_FILES=COPYING)
 
-cyclonedx: | buildroot/Makefile
-	@echo "Generating package information..."
-	@$(MAKE) --no-print-directory -C buildroot O=$(O) show-info | ./buildroot/utils/generate-cyclonedx > $(O)/cyclonedx-sbom.json
-	@echo "CycloneDX SBOM generated: $(O)/cyclonedx-sbom.json"
-
 # Workaround, see board/x86_64/board.mk
 test:
 	@+$(call bmake,$@)
@@ -44,4 +40,4 @@ test:
 buildroot/Makefile:
 	@git submodule update --init
 
-.PHONY: all check coverity dep test cyclonedx
+.PHONY: all check test

board/Config.in

@@ -1,6 +1,5 @@
 menu "Board Support"
 
-source "$BR2_EXTERNAL_INFIX_PATH/board/aarch32/Config.in"
 source "$BR2_EXTERNAL_INFIX_PATH/board/aarch64/Config.in"
 source "$BR2_EXTERNAL_INFIX_PATH/board/riscv64/Config.in"
 source "$BR2_EXTERNAL_INFIX_PATH/board/x86_64/Config.in"

board/aarch32/Config.in

@@ -1,5 +0,0 @@
-if BR2_arm
-
-source "$BR2_EXTERNAL_INFIX_PATH/board/aarch32/raspberrypi-rpi2/Config.in"
-
-endif

board/aarch32/README.md

@@ -1,7 +0,0 @@
-aarch32
-=======
-
-Board Specific Documentation
-----------------------------
-
-- [Raspberry Pi 2 Model B (32-bit)](raspberrypi-rpi2/)

board/aarch32/board.mk

@@ -1 +0,0 @@
-

board/aarch32/boot.script

@@ -1,7 +0,0 @@
-blkmap get boot dev devnum
-load blkmap ${devnum} ${kernel_addr_r} /boot/zImage
-#TODO: LOAD FDT
-
-setenv bootargs "${bootargs_root} ${bootargs_rauc} ${bootargs_log}"
-
-bootz ${kernel_addr_r} ${ramdisk} ${fdt_addr}

board/aarch32/linux_defconfig

@@ -1,395 +0,0 @@
-CONFIG_SYSVIPC=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_AUDIT=y
-CONFIG_NO_HZ_IDLE=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_BPF_SYSCALL=y
-CONFIG_BPF_JIT=y
-CONFIG_PREEMPT=y
-CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_BSD_PROCESS_ACCT_V3=y
-CONFIG_TASKSTATS=y
-CONFIG_TASK_DELAY_ACCT=y
-CONFIG_TASK_XACCT=y
-CONFIG_TASK_IO_ACCOUNTING=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=18
-CONFIG_MEMCG=y
-CONFIG_BLK_CGROUP=y
-CONFIG_CFS_BANDWIDTH=y
-CONFIG_RT_GROUP_SCHED=y
-CONFIG_CGROUP_PIDS=y
-CONFIG_CGROUP_FREEZER=y
-CONFIG_CPUSETS=y
-CONFIG_CGROUP_DEVICE=y
-CONFIG_CGROUP_CPUACCT=y
-CONFIG_CGROUP_PERF=y
-CONFIG_CGROUP_BPF=y
-CONFIG_USER_NS=y
-CONFIG_SCHED_AUTOGROUP=y
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_KALLSYMS_ALL=y
-CONFIG_PROFILING=y
-CONFIG_KEXEC=y
-CONFIG_ARCH_MULTI_V6=y
-CONFIG_ARCH_MULTI_V7=y
-CONFIG_ARCH_VIRT=y
-CONFIG_ARCH_BCM=y
-CONFIG_ARCH_BCM2835=y
-CONFIG_SMP=y
-CONFIG_NR_CPUS=4
-CONFIG_CPU_FREQ=y
-CONFIG_CPU_FREQ_STAT=y
-CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE=y
-CONFIG_CPU_FREQ_GOV_POWERSAVE=y
-CONFIG_CPU_FREQ_GOV_USERSPACE=y
-CONFIG_CPU_FREQ_GOV_ONDEMAND=y
-CONFIG_CPUFREQ_DT=y
-CONFIG_ARM_RASPBERRYPI_CPUFREQ=y
-CONFIG_AEABI=y
-CONFIG_VFP=y
-CONFIG_NEON=y
-CONFIG_KERNEL_MODE_NEON=y
-# CONFIG_SUSPEND is not set
-CONFIG_PM=y
-CONFIG_JUMP_LABEL=y
-# CONFIG_GCC_PLUGINS is not set
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_PARTITION_ADVANCED=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-# CONFIG_COMPAT_BRK is not set
-CONFIG_KSM=y
-CONFIG_CMA=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_XDP_SOCKETS=y
-CONFIG_XDP_SOCKETS_DIAG=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_ADVANCED_ROUTER=y
-CONFIG_IP_MULTIPLE_TABLES=y
-CONFIG_IP_ROUTE_MULTIPATH=y
-CONFIG_NET_IPIP=m
-CONFIG_NET_IPGRE_DEMUX=m
-CONFIG_NET_IPGRE=m
-CONFIG_NET_IPGRE_BROADCAST=y
-CONFIG_IP_MROUTE=y
-CONFIG_IP_MROUTE_MULTIPLE_TABLES=y
-CONFIG_IP_PIMSM_V1=y
-CONFIG_IP_PIMSM_V2=y
-CONFIG_SYN_COOKIES=y
-CONFIG_NET_IPVTI=m
-CONFIG_NET_FOU_IP_TUNNELS=y
-CONFIG_IPV6_SIT=m
-CONFIG_IPV6_GRE=m
-CONFIG_IPV6_MULTIPLE_TABLES=y
-CONFIG_IPV6_SUBTREES=y
-CONFIG_IPV6_MROUTE=y
-CONFIG_IPV6_MROUTE_MULTIPLE_TABLES=y
-CONFIG_IPV6_PIMSM_V2=y
-CONFIG_NETWORK_PHY_TIMESTAMPING=y
-CONFIG_NETFILTER=y
-CONFIG_BRIDGE_NETFILTER=y
-CONFIG_NETFILTER_NETLINK_QUEUE=y
-CONFIG_NETFILTER_NETLINK_LOG=y
-CONFIG_NF_CONNTRACK=y
-CONFIG_NF_CONNTRACK_EVENTS=y
-CONFIG_NF_CONNTRACK_FTP=y
-CONFIG_NF_TABLES=y
-CONFIG_NF_TABLES_INET=y
-CONFIG_NF_TABLES_NETDEV=y
-CONFIG_NFT_CT=m
-CONFIG_NFT_CONNLIMIT=m
-CONFIG_NFT_LOG=m
-CONFIG_NFT_LIMIT=m
-CONFIG_NFT_MASQ=m
-CONFIG_NFT_REDIR=m
-CONFIG_NFT_NAT=m
-CONFIG_NFT_TUNNEL=m
-CONFIG_NFT_QUEUE=m
-CONFIG_NFT_REJECT=m
-CONFIG_NFT_COMPAT=m
-CONFIG_NFT_HASH=m
-CONFIG_NFT_XFRM=m
-CONFIG_NFT_SOCKET=m
-CONFIG_NFT_OSF=m
-CONFIG_NFT_DUP_NETDEV=m
-CONFIG_NFT_FWD_NETDEV=m
-CONFIG_NFT_REJECT_NETDEV=m
-CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
-CONFIG_NETFILTER_XT_TARGET_LOG=m
-CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
-CONFIG_NETFILTER_XT_MATCH_BPF=m
-CONFIG_NETFILTER_XT_MATCH_CGROUP=m
-CONFIG_NETFILTER_XT_MATCH_COMMENT=m
-CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
-CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
-CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
-CONFIG_NETFILTER_XT_MATCH_DSCP=m
-CONFIG_NETFILTER_XT_MATCH_HELPER=m
-CONFIG_NETFILTER_XT_MATCH_LIMIT=m
-CONFIG_NETFILTER_XT_MATCH_MAC=m
-CONFIG_NETFILTER_XT_MATCH_MARK=m
-CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
-CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
-CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_FILTER=m
-CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_NAT=m
-CONFIG_IP_NF_TARGET_MASQUERADE=m
-CONFIG_IP_NF_MANGLE=m
-CONFIG_IP6_NF_IPTABLES=m
-CONFIG_IP6_NF_MATCH_AH=m
-CONFIG_IP6_NF_MATCH_EUI64=m
-CONFIG_IP6_NF_MATCH_IPV6HEADER=m
-CONFIG_IP6_NF_FILTER=m
-CONFIG_IP6_NF_TARGET_REJECT=m
-CONFIG_IP6_NF_RAW=m
-CONFIG_IP6_NF_NAT=m
-CONFIG_IP6_NF_TARGET_MASQUERADE=m
-CONFIG_IP6_NF_TARGET_NPT=m
-CONFIG_NF_TABLES_BRIDGE=m
-CONFIG_NFT_BRIDGE_META=m
-CONFIG_NF_CONNTRACK_BRIDGE=m
-CONFIG_BRIDGE_NF_EBTABLES=m
-CONFIG_BRIDGE_EBT_BROUTE=m
-CONFIG_BRIDGE_EBT_T_FILTER=m
-CONFIG_BRIDGE_EBT_T_NAT=m
-CONFIG_BRIDGE_EBT_802_3=m
-CONFIG_BRIDGE_EBT_ARP=m
-CONFIG_BRIDGE_EBT_IP=m
-CONFIG_BRIDGE_EBT_IP6=m
-CONFIG_BRIDGE_EBT_LIMIT=m
-CONFIG_BRIDGE_EBT_PKTTYPE=m
-CONFIG_BRIDGE_EBT_STP=m
-CONFIG_BRIDGE_EBT_VLAN=m
-CONFIG_BRIDGE_EBT_ARPREPLY=m
-CONFIG_BRIDGE_EBT_DNAT=m
-CONFIG_BRIDGE_EBT_REDIRECT=m
-CONFIG_BRIDGE_EBT_SNAT=m
-CONFIG_BRIDGE_EBT_LOG=m
-CONFIG_BRIDGE_EBT_NFLOG=m
-CONFIG_BRIDGE=y
-CONFIG_BRIDGE_VLAN_FILTERING=y
-CONFIG_BRIDGE_MRP=y
-CONFIG_BRIDGE_CFM=y
-CONFIG_NET_DSA=y
-CONFIG_VLAN_8021Q=y
-CONFIG_VLAN_8021Q_GVRP=y
-CONFIG_VLAN_8021Q_MVRP=y
-CONFIG_NET_SCHED=y
-CONFIG_NET_SCH_MQPRIO=y
-CONFIG_NET_CLS_BASIC=y
-CONFIG_NET_CLS_BPF=y
-CONFIG_NET_CLS_FLOWER=y
-CONFIG_NET_CLS_ACT=y
-CONFIG_NET_ACT_GACT=y
-CONFIG_NET_ACT_MIRRED=y
-CONFIG_NET_ACT_SKBEDIT=y
-CONFIG_DCB=y
-CONFIG_NETLINK_DIAG=y
-CONFIG_MPLS=y
-CONFIG_NET_MPLS_GSO=y
-CONFIG_MPLS_ROUTING=m
-CONFIG_MPLS_IPTUNNEL=m
-CONFIG_NET_PKTGEN=y
-# CONFIG_WIRELESS is not set
-CONFIG_NET_9P=y
-CONFIG_NET_9P_VIRTIO=y
-CONFIG_LWTUNNEL=y
-CONFIG_PCI=y
-CONFIG_PCIEPORTBUS=y
-CONFIG_PCI_IOV=y
-CONFIG_PCI_AARDVARK=y
-CONFIG_PCI_HOST_GENERIC=y
-CONFIG_PCIE_ARMADA_8K=y
-CONFIG_UEVENT_HELPER=y
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-# CONFIG_STANDALONE is not set
-CONFIG_RASPBERRYPI_FIRMWARE=y
-CONFIG_FW_CFG_SYSFS=y
-CONFIG_FW_CFG_SYSFS_CMDLINE=y
-CONFIG_OF_OVERLAY=y
-CONFIG_BLK_DEV_NULL_BLK=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_VIRTIO_BLK=y
-CONFIG_BLK_DEV_NVME=y
-CONFIG_SRAM=y
-CONFIG_EEPROM_AT24=y
-# CONFIG_SCSI_PROC_FS is not set
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_SCSI_SAS_LIBSAS=y
-CONFIG_SCSI_SAS_ATA=y
-CONFIG_SCSI_VIRTIO=y
-CONFIG_ATA=y
-CONFIG_SATA_AHCI=y
-CONFIG_SATA_MOBILE_LPM_POLICY=0
-CONFIG_SATA_AHCI_PLATFORM=y
-CONFIG_AHCI_MVEBU=y
-CONFIG_PATA_OF_PLATFORM=y
-CONFIG_MD=y
-CONFIG_BLK_DEV_DM=y
-CONFIG_DM_INIT=y
-CONFIG_DM_VERITY=y
-CONFIG_DM_VERITY_VERIFY_ROOTHASH_SIG=y
-CONFIG_NETDEVICES=y
-CONFIG_BONDING=m
-CONFIG_DUMMY=m
-CONFIG_MACVLAN=m
-CONFIG_MACVTAP=m
-CONFIG_IPVLAN=m
-CONFIG_IPVTAP=m
-CONFIG_VXLAN=m
-CONFIG_GENEVE=m
-CONFIG_BAREUDP=m
-CONFIG_MACSEC=m
-CONFIG_TUN=m
-CONFIG_VETH=m
-CONFIG_VIRTIO_NET=y
-CONFIG_NLMON=y
-CONFIG_NET_VRF=y
-CONFIG_BCMGENET=y
-CONFIG_SMSC911X=y
-CONFIG_USB_LAN78XX=y
-CONFIG_USB_USBNET=y
-CONFIG_USB_NET_SMSC95XX=y
-CONFIG_BRCMFMAC=m
-CONFIG_ZD1211RW=m
-CONFIG_INPUT_MOUSEDEV=m
-CONFIG_INPUT_EVDEV=y
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_TOUCHSCREEN_EDT_FT5X06=m
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_EXTENDED=y
-CONFIG_SERIAL_8250_SHARE_IRQ=y
-CONFIG_SERIAL_8250_BCM2835AUX=y
-CONFIG_SERIAL_AMBA_PL011=y
-CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-CONFIG_SERIAL_DEV_BUS=y
-CONFIG_TTY_PRINTK=y
-CONFIG_HVC_DRIVER=y
-CONFIG_VIRTIO_CONSOLE=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_BCM2835=m
-CONFIG_SPI=y
-CONFIG_SPI_BCM2835=y
-CONFIG_SPI_BCM2835AUX=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_SENSORS_RASPBERRYPI_HWMON=m
-CONFIG_THERMAL=y
-CONFIG_BCM2711_THERMAL=y
-CONFIG_BCM2835_THERMAL=m
-CONFIG_WATCHDOG=y
-CONFIG_BCM2835_WDT=y
-CONFIG_I6300ESB_WDT=y
-CONFIG_MFD_SYSCON=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_FIXED_VOLTAGE=y
-CONFIG_REGULATOR_GPIO=y
-CONFIG_MEDIA_SUPPORT=y
-CONFIG_DRM=y
-CONFIG_DRM_LOAD_EDID_FIRMWARE=y
-CONFIG_DRM_PANEL_SIMPLE=m
-CONFIG_DRM_TOSHIBA_TC358762=m
-CONFIG_DRM_V3D=m
-CONFIG_DRM_VC4=m
-CONFIG_DRM_VC4_HDMI_CEC=y
-CONFIG_DRM_SIMPLEDRM=y
-CONFIG_FB=y
-CONFIG_BACKLIGHT_CLASS_DEVICE=y
-CONFIG_SOUND=y
-CONFIG_SND=y
-CONFIG_SND_SOC=y
-CONFIG_SND_BCM2835_SOC_I2S=y
-CONFIG_HID_GENERIC=m
-CONFIG_USB=y
-CONFIG_USB_OTG=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_DWC2=y
-CONFIG_NOP_USB_XCEIV=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_ETH=m
-CONFIG_USB_ETH_EEM=y
-CONFIG_USB_G_SERIAL=m
-CONFIG_MMC=y
-CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_PLTFM=y
-CONFIG_MMC_SDHCI_IPROC=y
-CONFIG_MMC_BCM2835=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_TIMER=y
-CONFIG_LEDS_TRIGGER_ONESHOT=y
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-CONFIG_LEDS_TRIGGER_CPU=y
-CONFIG_LEDS_TRIGGER_GPIO=y
-CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
-CONFIG_LEDS_TRIGGER_TRANSIENT=y
-CONFIG_LEDS_TRIGGER_CAMERA=y
-CONFIG_DMADEVICES=y
-CONFIG_DMA_BCM2835=y
-CONFIG_VIRTIO_PCI=y
-CONFIG_VIRTIO_BALLOON=y
-CONFIG_VIRTIO_INPUT=y
-CONFIG_VIRTIO_MMIO=y
-CONFIG_STAGING=y
-CONFIG_SND_BCM2835=m
-CONFIG_VIDEO_BCM2835=m
-CONFIG_CLK_RASPBERRYPI=y
-CONFIG_MAILBOX=y
-CONFIG_BCM2835_MBOX=y
-# CONFIG_IOMMU_SUPPORT is not set
-CONFIG_RASPBERRYPI_POWER=y
-CONFIG_PWM=y
-CONFIG_PWM_BCM2835=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-CONFIG_EXT4_FS_POSIX_ACL=y
-CONFIG_BTRFS_FS=y
-CONFIG_BTRFS_FS_POSIX_ACL=y
-CONFIG_FANOTIFY=y
-CONFIG_FANOTIFY_ACCESS_PERMISSIONS=y
-CONFIG_QUOTA=y
-CONFIG_FUSE_FS=y
-CONFIG_VIRTIO_FS=y
-CONFIG_OVERLAY_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_EXFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_TMPFS_POSIX_ACL=y
-CONFIG_SQUASHFS=y
-CONFIG_SQUASHFS_LZO=y
-CONFIG_SQUASHFS_XZ=y
-CONFIG_SQUASHFS_ZSTD=y
-CONFIG_9P_FS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_NLS_UTF8=y
-CONFIG_CRYPTO_CCM=y
-CONFIG_CRYPTO_GCM=y
-# CONFIG_XZ_DEC_ARM is not set
-# CONFIG_XZ_DEC_ARMTHUMB is not set
-CONFIG_DMA_CMA=y
-CONFIG_CMA_SIZE_MBYTES=32
-CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_FS=y
-CONFIG_PANIC_ON_OOPS=y
-CONFIG_PANIC_TIMEOUT=20
-CONFIG_DETECT_HUNG_TASK=y
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_RCU_TRACE is not set
-CONFIG_FUNCTION_TRACER=y
-# CONFIG_STRICT_DEVMEM is not set
-CONFIG_MEMTEST=y

board/aarch32/raspberrypi-rpi2/Config.in

@@ -1,15 +0,0 @@
-config BR2_PACKAGE_RASPBERRYPI_RPI2
-	bool "Raspberry Pi 2 Model B (32-bit ARMv7)"
-	depends on BR2_arm
-	select SDCARD_AUX
-	select BR2_PACKAGE_FEATURE_WIFI
-	select BR2_PACKAGE_BRCMFMAC_SDIO_FIRMWARE_RPI
-	select BR2_PACKAGE_BRCMFMAC_SDIO_FIRMWARE_RPI_WIFI
-
-	help
-	  Support for the 32-bit ARMv7 Raspberry Pi 2B single-board computer
-	  (SBC) with BCM2836 quad-core Cortex-A7 processor.
-
-	  This was the only Raspberry Pi model with the BCM2836 and the 2B
-	  actually got a BCM2837 (Cortex-A53) underclocked an w/o wifi in
-	  the v1.2 board revision.

board/aarch32/raspberrypi-rpi2/LICENSE

@@ -1,13 +0,0 @@
-Copyright (c) 2025 The KernelKit Authors
-
-Permission to use, copy, modify, and/or distribute this software for any
-purpose with or without fee is hereby granted, provided that the above
-copyright notice and this permission notice appear in all copies.
-
-THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
-WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
-MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
-ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
-WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
-ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
-OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.

board/aarch32/raspberrypi-rpi2/README.md

@@ -1,96 +0,0 @@
-Raspberry Pi 2 Model B
-======================
-
-The [Raspberry Pi 2 Model B][1] is a 32-bit ARM single-board computer,
-powered by the Broadcom BCM2836 quad-core Cortex-A7 processor @ 900 MHz
-with 1 GB RAM.
-
-The board features:
-
-- 4x USB 2.0 ports
-- Fast Ethernet (100 Mbps)
-- microSD card slot for storage
-- HDMI port
-- GPIO header (40-pin)
-
-> [!NOTE]
-> Revision 1.2 of the Pi 2B actually uses a BCM2837 (Cortex-A53) underclocked
-> and without WiFi, making it very similar to the Pi 3B hardware-wise but
-> running in 32-bit mode.  This revision is not supported.
-
-How to Build
-------------
-
-Since there are no pre-built images for ARM32, you need to build both Infix
-and the bootloader from source.
-
-
-1. Clone the repository
-
-        git clone https://github.com/kernelkit/infix.git
-        cd infix
-
-2. Build the bootloader (in separate tree)
-
-        make O=x-boot rpi2_boot_defconfig
-        make O=x-boot
-
-3. Build Infix (in another tree)
-
-        make O=x-arm32 aarch32_defconfig
-        make O=x-arm32
-
-4. Create the SD card image
-
-        ./utils/mkimage.sh -b x-boot -r x-arm32 raspberrypi-rpi2
-
-The resulting image can be found in `x-boot/images/infix-arm-sdcard.img`
-
-Flashing to SD Card
--------------------
-
-[Flash the image][0] to a microSD card (at least 4 GB):
-
-```bash
-sudo dd if=x-boot/images/infix-arm-sdcard.img of=/dev/mmcblk0 \
-        bs=1M status=progress oflag=direct
-```
-
-You can also use `bmaptool`:
-
-```bash
-sudo bmaptool copy x-boot/images/infix-rpi2-sdcard.img /dev/mmcblk0
-```
-
-> [!WARNING]
-> Ensure `/dev/mmcblk0` is the correct device for your SD card and not used by
-> the host system! Use `lsblk` to verify.
-
-Booting the Board
------------------
-
-1. Insert the flashed SD card into the Raspberry Pi
-2. Connect an Ethernet cable (DHCP will be used to get an IP address)
-3. Power up the board using a 5V/2.5A micro-USB power supply
-
-The board will boot and obtain an IP address via DHCP on the Ethernet port.
-Find the assigned IP and SSH in with the default login credentials, user/pass:
-`admin` / `admin`.
-
-Console Port (Optional)
------------------------
-
-A serial console can be useful for debugging. Connect a USB-to-TTL
-serial adapter (3.3V) to GPIO pins:
-
-- GND → Pin 6, ground
-- TxD → Pin 8, GPIO 14
-- RxD → Pin 10, GPIO 15
-
-Serial settings: 115200 8N1
-
-> [!WARNING]
-> Use only 3.3V serial adapters. 5V adapters will damage your Raspberry Pi!
-
-[0]: https://kernelkit.org/posts/flashing-sdcard/
-[1]: https://www.raspberrypi.com/products/raspberry-pi-2-model-b/

board/aarch32/raspberrypi-rpi2/barebox/env/boot/mmc

@@ -1,11 +0,0 @@
-#!/bin/sh
-
-mkdir /mnt/primary
-mount /dev/disk0.primary /mnt/primary
-
-global.bootm.image="/mnt/primary/boot/zImage"
-global.bootm.oftree="/mnt/primary/boot/broadcom/bcm2836-rpi-2-b.dtb"
-global.linux.bootargs.base="quiet console=ttyAMA0,115200 console=tty1 rauc.slot=primary"
-global.linux.bootargs.dyn.root="root=PARTLABEL=primary rootwait ro"
-
-bootm

board/aarch32/raspberrypi-rpi2/barebox/env/config

@@ -1,12 +0,0 @@
-#!/bin/sh
-
-# Barebox configuration for Raspberry Pi 2
-
-# Boot timeout (seconds)
-global autoboot_timeout=3
-
-# Default boot order
-global boot.default="mmc net"
-
-# Enable colored output if supported
-global allow_color=true

board/aarch32/raspberrypi-rpi2/barebox/env/init/automount

@@ -1,5 +0,0 @@
-#!/bin/sh
-
-# Automount MMC partitions
-mkdir -p /mnt/mmc
-automount /mnt/mmc 'mci0.probe=1 && mount /dev/disk0.0 /mnt/mmc'

board/aarch32/raspberrypi-rpi2/barebox/env/init/bootorder

@@ -1,4 +0,0 @@
-#!/bin/sh
-
-# Set boot order: try mmc first, then network
-global.boot.default="mmc net"

board/aarch32/raspberrypi-rpi2/barebox/extras.config

@@ -1,17 +0,0 @@
-# Minimal Barebox configuration for Raspberry Pi 2
-# Basic boot only - A/B partitioning and secure boot to be added later
-
-# Enable custom embedded environment
-CONFIG_DEFAULT_ENVIRONMENT=y
-CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
-
-# Enable GPT partition table support for hybrid partition tables
-CONFIG_PARTITION_DISK_EFI=y
-
-# Enable SquashFS support for reading rootfs
-CONFIG_FS_SQUASHFS=y
-CONFIG_FS_SQUASHFS_LZ4=y
-CONFIG_FS_SQUASHFS_LZO=y
-CONFIG_FS_SQUASHFS_XZ=y
-CONFIG_FS_SQUASHFS_ZLIB=y
-CONFIG_FS_SQUASHFS_ZSTD=y

board/aarch32/raspberrypi-rpi2/cmdline.txt

@@ -1 +0,0 @@
-root=/dev/mmcblk0p2 rootwait console=tty1 console=ttyAMA0,115200

board/aarch32/raspberrypi-rpi2/config.txt

@@ -1,19 +0,0 @@
-# Raspberry Pi bootloader (start.elf) configuration
-#
-# uart_2ndstage=1 - Enable early boot debug output from the bootloader
-#                   Useful for debugging boot failures before Barebox starts
-#                   Comment out for production to reduce boot noise
-
-[all]
-kernel=barebox-raspberry-pi-2.img
-
-disable_overscan=1
-
-enable_uart=1
-#uart_2ndstage=1
-
-[pi2]
-start_file=start.elf
-fixup_file=fixup.dat
-
-gpu_mem=100

board/aarch32/raspberrypi-rpi2/dts/Makefile

@@ -1 +0,0 @@
-dtb-y += broadcom/bcm2836-rpi-2-b.dtb

board/aarch32/raspberrypi-rpi2/dts/broadcom/Makefile

@@ -1 +0,0 @@
-# Placeholder - dtb-y is defined in parent Makefile

board/aarch32/raspberrypi-rpi2/dts/broadcom/bcm2836-rpi-2-b.dts

@@ -1,19 +0,0 @@
-#include <arm/broadcom/bcm2836-rpi-2-b.dts>
-#include "infix.dtsi"
-
-/ {
-	/* CMA pool for GPU and video */
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		cma-reserved {
-			compatible = "shared-dma-pool";
-			size = <0x4000000>; /* 64MB */
-			alignment = <0x1000000>; /* 16MB aligned */
-			linux,cma-default;
-			reusable;
-		};
-	};
-};

board/aarch32/raspberrypi-rpi2/dts/broadcom/infix.dtsi

@@ -1,13 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Common Infix OS defaults
- */
-
-/ {
-	chosen {
-		infix {
-			/* Default admin user password: 'admin' */
-			factory-password-hash = "$5$mI/zpOAqZYKLC2WU$i7iPzZiIjOjrBF3NyftS9CCq8dfYwHwrmUK097Jca9A";
-		};
-	};
-};

board/aarch32/raspberrypi-rpi2/genimage.cfg.in

@@ -1,78 +0,0 @@
-image boot.vfat {
-	vfat {
-		files = {
-#BOOT_FILES#
-		}
-	}
-
-	size = 32M
-}
-
-image cfg.ext4 {
-	empty = true
-	temporary = true
-	size = 16M
-
-	ext4 {
-		label = "cfg"
-                use-mke2fs = true
-                features = "uninit_bg"
-                extraargs = "-m 0 -i 4096"
-	}
-}
-
-# The /var partition will be expanded automatically at first boot
-# to use the full size of the SD-card or eMMC media.
-image var.ext4 {
-	empty = true
-	temporary = true
-	size = 128M
-
-	ext4 {
-		label = "var"
-                use-mke2fs = true
-                features = "uninit_bg"
-                extraargs = "-m 0 -i 4096"
-	}
-}
-
-image #INFIX_ID##VERSION#-rpi2-sdcard.img {
-	hdimage {
-		partition-table-type = "hybrid"
-	}
-
-	partition boot {
-		partition-type = 0xc
-		bootable = "true"
-		image = "boot.vfat"
-	}
-
-	partition aux {
-		partition-type-uuid = srv
-		image = "aux.ext4"
-	}
-
-	partition primary {
-		partition-type-uuid = linux
-		bootable = "true"
-		size = 250M
-		image = "rootfs.squashfs"
-	}
-
-	partition secondary {
-		partition-type-uuid = linux
-		bootable = "true"
-		size = 250M
-		image = "rootfs.squashfs"
-	}
-
-	partition cfg {
-		partition-type-uuid = srv
-		image = "cfg.ext4"
-	}
-
-	partition var {
-		partition-type-uuid = var
-		image = "var.ext4"
-	}
-}

board/aarch32/raspberrypi-rpi2/raspberrypi-rpi2.mk

@@ -1,61 +0,0 @@
-# Raspberry Pi 2 Model B specific kernel configuration
-define RASPBERRYPI_RPI2_LINUX_CONFIG_FIXUPS
-	$(call KCONFIG_ENABLE_OPT,CONFIG_SOUND)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_SND)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_SND_SOC)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_INPUT_MOUSE)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_INPUT_KEYBOARD)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_INPUT_TOUCHSCREEN)
-	$(call KCONFIG_SET_OPT,CONFIG_INPUT_MOUSEDEV,m)
-	$(call KCONFIG_SET_OPT,CONFIG_HID_GENERIC,m)
-
-	$(call KCONFIG_ENABLE_OPT,CONFIG_ARCH_BCM)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_ARCH_BCM2835)
-	$(call KCONFIG_SET_OPT,CONFIG_BCM2835_MBOX,y)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_BCM2835_WDT)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_DMA_BCM2835)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_RASPBERRYPI_FIRMWARE)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_PINCTRL_BCM2835)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_GPIO_BCM2835)
-	$(call KCONFIG_SET_OPT,CONFIG_BRCMFMAC,m)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_BRCMFMAC_SDIO)
-	$(call KCONFIG_SET_OPT,CONFIG_I2C_BCM2835,m)
-	$(call KCONFIG_SET_OPT,CONFIG_BCM2835_THERMAL,m)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_MMC_BCM2835)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_RASPBERRYPI_POWER)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_SERIAL_8250)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_SERIAL_8250_CONSOLE)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_SERIAL_8250_BCM2835AUX)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_SERIAL_8250_EXTENDED)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_SERIAL_8250_SHARE_IRQ)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_NET_VENDOR_BROADCOM)
-	$(call KCONFIG_SET_OPT,CONFIG_SMSC911X,y)
-	$(call KCONFIG_SET_OPT,CONFIG_REGULATOR_GPIO,y)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_COMMON_CLK_BCM2835)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_CLK_RASPBERRYPI)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_DRM)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_DRM_KMS_HELPER)
-	$(call KCONFIG_SET_OPT,CONFIG_DRM_V3D,m)
-	$(call KCONFIG_SET_OPT,CONFIG_DRM_VC4,m)
-	$(call KCONFIG_SET_OPT,CONFIG_STAGING,y)
-	$(call KCONFIG_SET_OPT,CONFIG_SND_BCM2835,m)
-
-	$(call KCONFIG_ENABLE_OPT,CONFIG_DRM_VC4_HDMI_CEC)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_DRM_LOAD_EDID_FIRMWARE)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_DRM_PANEL_BRIDGE)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_DRM_BRIDGE)
-	$(call KCONFIG_SET_OPT,CONFIG_DRM_TOSHIBA_TC358762,m)
-	$(call KCONFIG_SET_OPT,CONFIG_DRM_PANEL_SIMPLE,m)
-
-	$(call KCONFIG_ENABLE_OPT,CONFIG_FB)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_FRAMEBUFFER_CONSOLE)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY)
-	$(call KCONFIG_ENABLE_OPT,CONFIG_DRM_FBDEV_EMULATION)
-
-	$(call KCONFIG_SET_OPT,CONFIG_TOUCHSCREEN_EDT_FT5X06,m)
-
-	$(call KCONFIG_ENABLE_OPT,CONFIG_BACKLIGHT_CLASS_DEVICE)
-endef
-
-$(eval $(ix-board))
-$(eval $(generic-package))

board/aarch32/raspberrypi-rpi2/rootfs/usr/share/product/raspberrypi,2-model-b/etc/factory-config.cfg

@@ -1,206 +0,0 @@
-{
-  "ieee802-dot1ab-lldp:lldp": {
-    "infix-lldp:enabled": true
-  },
-  "ietf-hardware:hardware": {
-    "component": [
-      {
-        "name": "USB",
-        "class": "infix-hardware:usb",
-        "state": {
-          "admin-state": "unlocked"
-        }
-      }
-    ]
-  },
-  "ietf-interfaces:interfaces": {
-    "interface": [
-      {
-        "name": "lo",
-        "type": "infix-if-type:loopback",
-        "ietf-ip:ipv4": {
-          "address": [
-            {
-              "ip": "127.0.0.1",
-              "prefix-length": 8
-            }
-          ]
-        },
-        "ietf-ip:ipv6": {
-          "address": [
-            {
-              "ip": "::1",
-              "prefix-length": 128
-            }
-          ]
-        }
-      },
-      {
-        "name": "eth0",
-        "type": "infix-if-type:ethernet",
-        "ietf-ip:ipv4": {
-          "infix-dhcp-client:dhcp": {
-            "option": [
-              {"id": "netmask"},
-              {"id": "broadcast"},
-              {"id": "router"},
-              {"id": "domain"},
-              {"id": "hostname"},
-              {"id": "dns-server"},
-              {"id": "ntp-server"},
-              {"id": "vendor-class", "value": "Raspberry Pi 2 Model B"}
-            ]
-          }
-        }
-      }
-    ]
-  },
-  "ietf-keystore:keystore": {
-    "asymmetric-keys": {
-      "asymmetric-key": [
-        {
-          "name": "genkey",
-          "public-key-format": "infix-crypto-types:ssh-public-key-format",
-          "public-key": "",
-          "private-key-format": "infix-crypto-types:rsa-private-key-format",
-          "cleartext-private-key": "",
-          "certificates": {}
-        }
-      ]
-    }
-  },
-  "ietf-netconf-acm:nacm": {
-    "enable-nacm": true,
-    "groups": {
-      "group": [
-        {
-          "name": "admin",
-          "user-name": [
-            "admin"
-          ]
-        }
-      ]
-    },
-    "rule-list": [
-      {
-        "name": "admin-acl",
-        "group": [
-          "admin"
-        ],
-        "rule": [
-          {
-            "name": "permit-all",
-            "module-name": "*",
-            "access-operations": "*",
-            "action": "permit",
-            "comment": "Allow 'admin' group complete access to all operations and data."
-          }
-        ]
-      },
-      {
-        "name": "default-deny-all",
-        "group": [
-          "*"
-        ],
-        "rule": [
-          {
-            "name": "deny-password-read",
-            "module-name": "ietf-system",
-            "path": "/ietf-system:system/authentication/user/password",
-            "access-operations": "*",
-            "action": "deny"
-          }
-        ]
-      }
-    ]
-  },
-  "ietf-netconf-server:netconf-server": {
-    "listen": {
-      "endpoints": {
-        "endpoint": [
-          {
-            "name": "default-ssh",
-            "ssh": {
-              "tcp-server-parameters": {
-                "local-address": "::"
-              },
-              "ssh-server-parameters": {
-                "server-identity": {
-                  "host-key": [
-                    {
-                      "name": "default-key",
-                      "public-key": {
-                        "central-keystore-reference": "genkey"
-                      }
-                    }
-                  ]
-                }
-              }
-            }
-          }
-        ]
-      }
-    }
-  },
-  "ietf-system:system": {
-    "hostname": "rpi-%m",
-    "ntp": {
-      "enabled": true,
-      "server": [
-        {
-          "name": "ntp.org",
-          "udp": {
-            "address": "pool.ntp.org"
-          },
-          "iburst": true
-        }
-      ]
-    },
-    "authentication": {
-      "user": [
-        {
-          "name": "admin",
-          "password": "$factory$",
-          "infix-system:shell": "bash"
-        }
-      ]
-    },
-    "infix-system:motd-banner": "Li0tLS0tLS0uCnwgIC4gLiAgfCBJbmZpeCBPUyDigJQgSW1tdXRhYmxlLkZyaWVuZGx5LlNlY3VyZQp8LS4gdiAuLXwgaHR0cHM6Ly9rZXJuZWxraXQub3JnCictJy0tLSctJwo="
-  },
-  "infix-meta:meta": {
-    "version": "1.6"
-  },
-  "infix-services:mdns": {
-    "enabled": true
-  },
-  "infix-services:web": {
-    "enabled": true,
-    "console": {
-      "enabled": true
-    },
-    "netbrowse": {
-      "enabled": true
-    },
-    "restconf": {
-      "enabled": true
-    }
-  },
-  "infix-services:ssh": {
-    "enabled": true,
-    "hostkey": [
-      "genkey"
-    ],
-    "listen": [
-      {
-        "name": "ipv4",
-        "address": "0.0.0.0",
-        "port": 22
-      },
-      {
-        "name": "ipv6",
-        "address": "::",
-        "port": 22
-      }
-    ]
-  }
-}

board/aarch32/raspberrypi-rpi2/rootfs/usr/share/product/raspberrypi,2-model-b/etc/product/interface-quirks.json

@@ -1,8 +0,0 @@
-{
-    "eth0": {
-	"phy-detached-when-down": true
-    },
-    "@ethtool:driver=smsc95xx": {
-        "broken-flow-control": true
-    }
-}

board/aarch32/raspberrypi-rpi2/uboot/extras.config

@@ -1,13 +0,0 @@
-# CONFIG_MMC_PCI is not set
-CONFIG_OF_OVERLAY_LIST="rpi-env infix-key"
-# CONFIG_ENV_IS_IN_FAT is not set
-
-# Increase early malloc heap to handle DTB with embedded scripts
-CONFIG_SYS_MALLOC_F_LEN=0x2000
-
-# Compression support needed for SquashFS
-CONFIG_LZ4=y
-CONFIG_LZMA=y
-CONFIG_CMD_LZMADEC=y
-CONFIG_CMD_UNLZ4=y
-CONFIG_CMD_UNZIP=y

board/aarch32/raspberrypi-rpi2/uboot/rpi-env.dtso

@@ -1,27 +0,0 @@
-/dts-v1/;
-/plugin/;
-
-&{/} {
-	config {
-		environment {
-			vendor = "infix";
-			preboot = "run ixpreboot";
-			ixbootdelay = "0.5";
-			bootdelay = "-2";
-			bootmenu_delay = "10";
-			boot_targets = "mmc0";
-			ethprime = "eth0";
-			bootcmd = "run ixboot";
-
-			ixpreboot     = /incbin/("scripts/ixpreboot.sh");
-			ixbtn-devmode = "setenv dev_mode yes; echo Enabled";
-			ixbtn-factory = "echo \"No button available, use bootmenu\"";
-			ixfactory     = /incbin/("scripts/ixfactory.sh");
-
-			ixboot      = /incbin/("scripts/ixboot.sh");
-			ixbootslot  = /incbin/("scripts/ixbootslot.sh");
-			ixprepblk   = /incbin/("scripts/ixprepblk.sh");
-			ixprepdhcp  = /incbin/("scripts/ixprepdhcp.sh");
-		};
-	};
-};

board/aarch64/bananapi-bpi-r3/README.md

@@ -1,229 +1,27 @@
-# Banana Pi BPI-R3
+# Banana Pi R3
+
+## Support level
+Full support for all Infix enabled features including switched ethernet ports, WiFi,
+and SFP interfaces. The board includes comprehensive hardware support for
+MediaTek MT7986 SoC features.
+
+### Hardware features
+The Banana Pi R3 is a high-performance networking board featuring:
+- MediaTek MT7986 ARM Cortex-A53 quad-core processor
+- 4x Gigabit LAN ports (lan1-lan4)
+- 1x Gigabit WAN port
+- 2x SFP ports (sfp1, sfp2) for fiber connectivity
+- Dual WiFi interfaces (wifi0 for 2.4GHz, wifi1 for 5GHz)
+- USB support
+- SD card boot support
+
+### Network configuration
+The board comes preconfigured with:
+- 4 switched LAN ports for internal networking
+- Dedicated WAN port with DHCP client enabled
+- SFP ports for high-speed fiber connections
+- Dual WiFi interfaces for wireless connectivity
+
+### Pre-built images
+SD card image: [infix-bpi-r3-sdcard.img](https://github.com/kernelkit/infix/releases/download/latest-boot/infix-bpi-r3-sdcard.img)
 
-<img src="bananapi-bpi-r3.webp" alt="The board" width=800 padding=10>
-
-## Overview
-
-The Banana Pi R3 is a high-performance networking board with full Infix
-support for all enabled features including switched Ethernet ports, WiFi,
-and SFP interfaces.
-
-### Hardware Features
-
-- MediaTek MT7986 ARM Cortex-A53 quad-core processor @ 2.0 GHz
-- 2 GB DDR4 RAM
-- 8 GB eMMC storage + microSD card slot
-- 5x Gigabit Ethernet ports (4x LAN, 1x WAN)
-- 2x SFP cages for fiber connectivity (1G/2.5G)
-- Dual-band WiFi (2.4 GHz + 5 GHz)
-- USB 3.0 port
-- Mini PCIe slot
-
-### Default Network Configuration
-
-Infix comes preconfigured with:
-
-- **LAN ports** (lan1-lan4): Bridged for internal networking
-- **WAN port**: DHCP client enabled for internet connectivity
-- **SFP ports** (sfp1, sfp2): Available for configuration
-- **WiFi interfaces** (wifi0, wifi1): Available for configuration
-
-## Getting Started
-
-### Quick Start with SD Card
-
-The easiest way to get started is using an SD card:
-
-1. **Download the SD card image:** [infix-bpi-r3-sdcard.img][2]
-2. **Flash the image to an SD card:** see [this guide][0]
-3. **Set boot switches:**
-   - Set DIP switches to **0000** (SD card boot mode)
-   - Switch positions are on the underside of the board near the SD slot
-4. **Boot the board:**
-   - Insert the SD card
-   - Connect power
-   - Connect to LAN port or console (115200 8N1)
-   - Default login: `admin` / `admin`
-
-### Boot Switch Reference
-
-The BPI-R3 has a 4-position DIP switch that controls boot media:
-
-<img align="right" src="bootstrap-switch.webp" alt="DIP switches" width=200 padding=10>
-
-| Position | Mode        | Description                           |
-|----------|-------------|---------------------------------------|
-| 0000     | SD card     | Boot from microSD card (recommended)  |
-| 0110     | eMMC        | Boot from internal eMMC storage       |
-| 1010     | SPI NAND    | Boot from SPI NAND (advanced users)   |
-
-> [!NOTE]
-> Switch position is read from left to right: "0" = OFF, "1" = ON.  
-> When the DIP switch is in the "UP" position it is OFF(0).
-
-## Advanced: Installing to eMMC
-
-For production deployments or better performance, you can install Infix
-to the internal eMMC storage. This is more complex but provides faster
-boot times and eliminates the external SD card.
-
-### Why Use eMMC?
-
-**Advantages:**
-
-- Faster boot and better performance
-- No external SD card to manage
-- More robust for industrial/embedded deployments
-
-**Disadvantages:**
-
-- More complex installation process
-- Requires intermediate NAND boot step
-- Harder to recover from errors
-
-### Prerequisites
-
-- FTDI USB-to-serial cable (3.3V) for console access
-- microSD card with Infix (for initial boot)
-- USB flash drive (FAT32 formatted)
-- Downloaded files (see below)
-
-### Required Files
-
-Download and place these files on a FAT32-formatted USB drive:
-
-1. **Intermediate NAND bootloader** (from Frank-W's U-Boot):
-   - [bpi-r3_spim-nand_bl2.img][5] (BL2 loader)
-   - [bpi-r3_spim-nand_fip.bin][6] (FIP image)
-2. **Infix eMMC image:**
-   - [infix-bpi-r3-emmc.img][3] (Complete system image)
-3. **eMMC bootloader** (extracted from):
-   - [bpi-r3-emmc-boot-2025.01-latest.tar.gz][4]
-   - Extract `bl2.img` from the tarball to your USB drive
-
-> [!WARNING]
-> The following process involves multiple boot mode changes.  Take your
-> time verify each step carefully.
-
-### Installation Steps
-
-#### Step 1: Boot from SD card
-
-1. Set boot switches to **0000** (SD card mode)
-2. Insert SD card with Infix
-3. Power on and break into U-Boot (press Ctrl-C during boot)
-
-#### Step 2: Flash intermediate NAND bootloader
-
-This step installs a temporary bootloader to NAND that will help us
-flash the eMMC. From the U-Boot prompt:
-
-```
-usb start
-mtd erase spi-nand0
-fatload usb 0:1 0x50000000 bpi-r3_spim-nand_bl2.img
-mtd write spi-nand0 0x50000000 0x0 0x100000
-fatload usb 0:1 0x50000000 bpi-r3_spim-nand_fip.bin
-mtd write spi-nand0 0x50000000 0x380000 0x200000
-```
-
-#### Step 3: Boot from NAND
-
-1. Power off the board
-2. Set boot switches to **1010** (NAND mode)
-3. Power on - you should boot into U-Boot again
-
-#### Step 4: Write Infix image to eMMC
-
-From the U-Boot prompt:
-
-```
-usb start
-fatload usb 0:1 0x50000000 infix-bpi-r3-emmc.img
-setexpr blocks ${filesize} / 0x200
-mmc write 0x50000000 0x0 ${blocks}
-```
-
-This writes the complete Infix system (partitions, rootfs, etc.) to eMMC.
-
-#### Step 5: Configure eMMC boot
-
-Now configure the eMMC boot partition and write the bootloader:
-
-```
-mmc partconf 0 1 1 1
-mmc erase 0x0 0x400
-fatload usb 0:1 0x50000000 bl2.img
-mmc write 0x50000000 0x0 0x400
-mmc partconf 0 1 1 0
-```
-
-#### Step 6: Boot from eMMC
-
-1. Power off the board
-2. Set boot switches to **0110** (eMMC mode)
-3. Remove SD card (optional, but recommended to verify eMMC boot)
-4. Power on
-
-Your BPI-R3 should now boot Infix from internal eMMC storage!
-
-## Troubleshooting
-
-### Board won't boot
-
-- Verify boot switch positions (check twice!)
-- Ensure power supply provides adequate current (12V/2A recommended)
-- Try booting from SD card with switches at **0000**
-
-### Can't break into U-Boot
-
-- Ensure serial console is connected properly (115200 8N1, 3.3V)
-- Press Ctrl-C immediately when you see boot messages
-- Try power cycling and pressing Ctrl-C repeatedly
-
-### eMMC boot fails after installation
-
-- Boot from NAND (**1010**) and verify eMMC image was written
-- Check USB drive contents - ensure all files are present
-- Re-run Step 5 (eMMC boot configuration)
-
-### Reverting to SD card
-
-Simply set boot switches back to **0000** and boot from SD card. The
-eMMC installation does not affect SD card functionality.
-
-## Additional Resources
-
-- [Infix Documentation][1]
-- [Official BPI-R3 Wiki][7]
-- [Release Downloads][8]
-
-## Building Custom Images
-
-See the main Infix documentation for building from source. To build both
-SD card and eMMC images locally:
-
-```bash
-# Build bootloaders for both SD and eMMC
-make x-bpi-r3-sd-boot
-make x-bpi-r3-emmc-boot
-
-# Build main system
-make aarch64
-
-# Create SD card image
-./utils/mkimage.sh -od bananapi-bpi-r3
-
-# Create eMMC image
-./utils/mkimage.sh -odt emmc bananapi-bpi-r3
-```
-
-[0]: https://kernelkit.org/posts/flashing-sdcard/
-[1]: https://kernelkit.org/infix/latest/
-[2]: https://github.com/kernelkit/infix/releases/download/latest-boot/infix-bpi-r3-sdcard.img
-[3]: https://github.com/kernelkit/infix/releases/download/latest-boot/infix-bpi-r3-emmc.img
-[4]: https://github.com/kernelkit/infix/releases/download/latest-boot/bpi-r3-emmc-boot-2025.01-latest.tar.gz
-[5]: https://github.com/frank-w/u-boot/releases/download/CI-BUILD-2025-10-bpi-2025.10-2025-10-13_1032/bpi-r3_spim-nand_bl2.img
-[6]: https://github.com/frank-w/u-boot/releases/download/CI-BUILD-2025-10-bpi-2025.10-2025-10-13_1032/bpi-r3_spim-nand_fip.bin
-[7]: https://wiki.banana-pi.org/Banana_Pi_BPI-R3
-[8]: https://github.com/kernelkit/infix/releases/tag/latest-boot

board/aarch64/bananapi-bpi-r3/dts/Makefile

@@ -1 +1 @@
-dtb-y += mediatek/mt7986a-bananapi-bpi-r3-sd.dtb mediatek/mt7986a-bananapi-bpi-r3-emmc.dtb
+dtb-y += mediatek/mt7986a-bananapi-bpi-r3-sd.dtb

board/aarch64/bananapi-bpi-r3/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts

@@ -1,2 +0,0 @@
-#include "mt7986a-bananapi-bpi-r3.dtsi"
-#include "mt7986a-bananapi-bpi-r3-emmc.dtsi"

board/aarch64/bananapi-bpi-r3/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtsi

@@ -1,22 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Copyright (C) 2021 MediaTek Inc.
- * Author: Sam.Shih <sam.shih@mediatek.com>
- */
-
-/*
-This is copied from linux where it is an overlay, unfortunatly it is not
-possible to use dtbo in sysboot unless present in syslinux.conf
-*/
-&{/soc/mmc@11230000} {
-        bus-width = <8>;
-        max-frequency = <200000000>;
-        cap-mmc-highspeed;
-        mmc-hs200-1_8v;
-        mmc-hs400-1_8v;
-        hs400-ds-delay = <0x14014>;
-        non-removable;
-        no-sd;
-        no-sdio;
-        status = "okay";
-};

board/aarch64/bananapi-bpi-r3/genimage.cfg.in

@@ -24,7 +24,7 @@ image var.ext4 {
         }
 }
 
-image #INFIX_ID##VERSION#-bpi-r3-#TARGET#.img {
+image #INFIX_ID##VERSION#-bpi-r3-sdcard.img {
         hdimage {
                 partition-table-type = "gpt"
 

board/aarch64/bananapi-bpi-r3/rootfs/usr/share/product/bananapi,bpi-r3/etc/factory-config.cfg

@@ -99,6 +99,7 @@
       {
         "name": "wan",
         "type": "infix-if-type:ethernet",
+        "ietf-ip:ipv6": {},
         "ietf-ip:ipv4": {
           "infix-dhcp-client:dhcp": {
             "option": [
@@ -108,18 +109,7 @@
               {"id": "hostname"},
               {"id": "dns-server"},
               {"id": "router"},
-              {"id": "netmask"},
+              {"id": "netmask"}
-              {"id": "vendor-class", "value": "Banana Pi BPI-R3"}
-            ]
-          }
-        },
-        "ietf-ip:ipv6": {
-          "infix-dhcpv6-client:dhcp": {
-            "option": [
-              {"id": "ntp-server"},
-              {"id": "client-fqdn"},
-              {"id": "domain-search"},
-              {"id": "dns-server"}
             ]
           }
         }
@@ -293,7 +283,6 @@
     "policy": [
       {
         "name": "lan-to-wan",
-	"action": "accept",
         "ingress": [
           "lan"
         ],

board/aarch64/bananapi-bpi-r3/uboot/emmc-extras.config

@@ -1,3 +0,0 @@
-CONFIG_DEVICE_TREE_INCLUDES="infix-env.dtsi infix-key.dtsi mt7986-emmc-env.dtsi"
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES="BOOT_DEVICE=emmc DRAM_USE_DDR4=1 USE_MKIMAGE=1  MKIMAGE=$(HOST_DIR)/bin/mkimage"
-CONFIG_SUPPORT_EMMC_BOOT=y

board/aarch64/bananapi-bpi-r3/uboot/extras.config

@@ -7,27 +7,6 @@ CONFIG_USB=y
 CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_XHCI_MTK=y
 CONFIG_USB_MTU3=y
+CONFIG_CMD_USB=y
 CONFIG_PHY=y
 CONFIG_PHY_MTK_TPHY=y
-
-CONFIG_MTK_SPIM=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_SPI_FLASH=y
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SPI_FLASH_MTD=y
-CONFIG_SPI_FLASH_MACRONIX=y
-CONFIG_SPI_FLASH_WINBOND=y
-CONFIG_SPI_FLASH_GIGADEVICE=y
-CONFIG_MTD=y
-CONFIG_DM_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_SPI_NAND=y
-CONFIG_MTK_SPIM=y
-CONFIG_MTK_SNOR=y
-
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_MTD=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_CMD_DM=y

board/aarch64/bananapi-bpi-r3/uboot/mt7986-emmc-env.dtsi

@@ -1,5 +0,0 @@
-#include <mt7986-env.dtsi>
-
-&env {
-      fdtfile = "mediatek/mt7986a-bananapi-bpi-r3-emmc.dtb";
-};

board/aarch64/board.mk

@@ -1,4 +1,3 @@
-include $(sort $(wildcard $(BR2_EXTERNAL_INFIX_PATH)/board/aarch64/*/*.mk))
 
 .PHONY: board-enable-qemu-uboot
 board-enable-qemu-uboot:
@@ -20,6 +19,13 @@ board-enable-qemu-uboot:
 			'$$(BR2_EXTERNAL_INFIX_PATH)/board/common/uboot/extras.config' \
 		--enable TARGET_UBOOT_FORMAT_DTB
 
+.PHONY: board-enable-sparx-fit
+board-enable-sparx-fit:
+	@$(call IXMSG,"Enabling SparX-5i compatible FIT options")
+	@BR2_PREFIX= ./utils/config --file $(BR2_CONFIG) \
+	 	--enable FIT_IMAGE \
+	 	--set-str FIT_KERNEL_LOAD_ADDR "0x7 0x00000000"
+
 .PHONY: board-sparx-flash-uboot
 board-sparx-flash-uboot: $(BINARIES_DIR)/u-boot.bin
 	@grep -q 'BR2_TARGET_UBOOT_BOARD_DEFCONFIG="mscc_fireant_pcb135_emmc"' $(BR2_CONFIG) || \

board/aarch64/friendlyarm-nanopi-r2s/rootfs/usr/share/product/friendlyarm,nanopi-r2s/etc/factory-config.cfg

@@ -58,6 +58,7 @@
       {
         "name": "wan",
         "type": "infix-if-type:ethernet",
+        "ietf-ip:ipv6": {},
         "ietf-ip:ipv4": {
           "infix-dhcp-client:dhcp": {
             "option": [
@@ -67,18 +68,7 @@
               {"id": "hostname"},
               {"id": "dns-server"},
               {"id": "router"},
-              {"id": "netmask"},
+              {"id": "netmask"}
-              {"id": "vendor-class", "value": "NanoPi R2S"}
-            ]
-          }
-        },
-        "ietf-ip:ipv6": {
-          "infix-dhcpv6-client:dhcp": {
-            "option": [
-              {"id": "ntp-server"},
-              {"id": "client-fqdn"},
-              {"id": "domain-search"},
-              {"id": "dns-server"}
             ]
           }
         }
@@ -244,7 +234,6 @@
     "policy": [
       {
         "name": "lan-to-wan",
-	"action": "accept",
         "ingress": [
           "lan"
         ],

board/aarch64/raspberrypi-rpi64/README.md

@@ -1,322 +1,59 @@
-# Raspberry Pi 3B/4B/CM4
+# Raspberry Pi 3B/4B
 
-## Overview
+## Support level
 
-The Raspberry Pi is one of the most popular single-board computers with full
+Full support for base board but not any extension board on the GPIOs.
-Infix support for networking features, making it an excellent platform for
+Other RPi boards of the same generation may work as well, but may need
-learning, prototyping, and lightweight network applications.
+some additional testing/work.  A few CM4 variants have been tested and
+seem to work as expected, but YMMV as always.
 
-### Hardware Features
+### Touch screen
 
-**Raspberry Pi 3B:**
+The [Raspberry Pi touch display v1][0] is supported on the 4B, including
+touch functionality.  There are multiple touchscreens on the market for
+Raspberry Pi, but currently only the official first version with 800x480
+resolution is supported.  Infix supplies all drivers required to utilize
+the hardware, but you need to add the actual graphical application in a
+container.
 
-- Broadcom BCM2837B0 ARM Cortex-A53 quad-core processor @ 1.4 GHz
+There are some important considerations you need to know about when
-- 1 GB LPDDR2 RAM
+using Infix for graphical applications.  The container needs access to
-- microSD card slot for storage
+`/dev/dri/` to be able to access the graphics card, it also need access
-- 4x USB 2.0 ports
+to `/run/udev` to be able to find the input devices.
-- Fast Ethernet (100 Mbps)
-- Dual-band WiFi (2.4 GHz + 5 GHz) and Bluetooth 4.2
-- HDMI port
-- GPIO header (40-pin)
 
-**Raspberry Pi 4B:**
+Example of running Doom in Infix:
-
-- Broadcom BCM2711 ARM Cortex-A72 quad-core processor @ 1.5 GHz
-- 1 GB, 2 GB, 4 GB, or 8 GB LPDDR4 RAM (depending on model)
-- microSD card slot for storage
-- 2x USB 3.0 + 2x USB 2.0 ports
-- Gigabit Ethernet
-- Dual-band WiFi (2.4 GHz + 5 GHz) and Bluetooth 5.0
-- 2x micro-HDMI ports (up to 4K output)
-- GPIO header (40-pin)
-- PoE support (with add-on HAT)
-
-**Compute Module 4 (CM4):**
-
-- Same processor as Pi 4B
-- Compact form factor for embedded applications
-- Optional eMMC storage (0 GB, 8 GB, 16 GB, or 32 GB)
-- Requires carrier board for I/O connectivity
-- Various configurations tested and working
-
-### Default Network Configuration
-
-Infix comes preconfigured with:
-
-- **Ethernet port**: DHCP client enabled for internet connectivity
-- **WiFi interfaces** (wlan0, wlan1): Available for configuration as AP or client
-- **GPIO**: Available but extension boards not currently supported
-
-### Support Level
-
-Full support for base board networking and core functionality. GPIO extension
-boards (HATs) are not currently supported. Other Raspberry Pi boards of the
-same generation may work but may require additional testing.
-
-## Getting Started
-
-### Quick Start with SD Card
-
-The easiest way to get started is using a microSD card:
-
-1. **Download the SD card image:** [infix-rpi64-sdcard.img][2]
-2. **Flash the image to a microSD card:** see [this guide][0]
-3. **Boot the board:**
-   - Insert the microSD card into your Raspberry Pi
-   - Connect an Ethernet cable to your network
-   - Connect power (see [Power Supply Requirements](#power-supply-requirements))
-   - The board will boot automatically
-4. **Connect and login:**
-   - SSH to the DHCP-assigned IP address
-   - Default login: `admin` / `admin`
-
-> [!NOTE]
-> Raspberry Pi 3B and 4B boot with a factory configuration (`factory-config.cfg`)
-> that enables DHCP client on the Ethernet port. This means you can access
-> the device over the network without needing a serial console. Simply find
-> the assigned IP address and SSH in!
->
-> **Compute Module 4 (CM4)** and some other variants do not have this factory
-> configuration, so you'll need to use a serial console for initial setup or
-> configure the carrier board accordingly.
-
-### First Boot Notes
-
-On first boot, Infix will:
-
-- Obtain an IP address via DHCP on the Ethernet port
-- Generate unique SSH host keys
-- Initialize the configuration system
-
-You can find the assigned IP address by:
-
-- Checking your DHCP server/router's client list
-- Using network scanning tools like `nmap` or `arp-scan`
-- Connecting via serial console and running `ip addr` (if needed)
-
-## Hardware-Specific Features
-
-### WiFi Configuration
-
-Both Pi 3B and Pi 4B include dual-band WiFi that can be configured as a
-client (station mode). See the [Infix WiFi documentation][9] for detailed
-configuration examples.
-
-To configure WiFi as a client, first store your WiFi password in the keystore:
 
 ```
-admin@infix:/> configure
+admin@example:/> configure
-admin@infix:/config/> edit keystore symmetric-key mywifi
+admin@example:/config/> edit container doom
-admin@infix:/config/keystore/…/mywifi/> set key-format wifi-preshared-key-format
+admin@example:/config/container/doom/> set image docker://mattiaswal/alpine-doom:latest
-admin@infix:/config/keystore/…/mywifi/> set cleartext-key YourWiFiPassword
+admin@example:/config/container/doom/> set privileged
-admin@infix:/config/keystore/…/mywifi/> leave
+admin@example:/config/container/doom/> edit mount udev
-```
+admin@example:/config/container/doom/mount/udev/> set type bind
-
+admin@example:/config/container/doom/mount/udev/> set target /run/udev/
-Then configure the WiFi interface using the keystore reference:
+admin@example:/config/container/doom/mount/udev/> set source /run/udev/
-
+admin@example:/config/container/doom/mount/udev/> end
-```
+admin@example:/config/container/doom/mount/xorg.conf/> set content U2VjdGlvbiAiT3V0cHV0Q2xhc3MiCiAgSWRlbnRpZmllciAidmM0IgogIE1hdGNoRHJpdmVyICJ2YzQiCiAgRHJpdmVyICJtb2Rlc2V0dGluZyIKICBPcHRpb24gIlByaW1hcnlHUFUiICJ0cnVlIgpFbmRTZWN0aW9uCg==
-admin@infix:/> configure
+admin@example:/config/container/doom/mount/xorg.conf/> set target /etc/X11/xorg.conf
-admin@infix:/config/> edit interface wifi0
+admin@example:/config/container/doom/mount/xorg.conf/> end
-admin@infix:/config/interface/wifi0/> set ipv4 dhcp-client
+admin@example:/config/container/doom/> edit volume var
-admin@infix:/config/interface/wifi0/> set wifi ssid YourNetworkName
+admin@example:/config/container/doom/volume/var/> set target /var
-admin@infix:/config/interface/wifi0/> set wifi secret mywifi
+admin@example:/config/container/doom/volume/var/> leave
-admin@infix:/config/interface/wifi0/> set wifi country-code US
+admin@example:/>
-admin@infix:/config/interface/wifi0/> leave
 ```
 
 > [!NOTE]
-> The WiFi password (8-63 characters) is stored securely in the keystore as
+> The `xorg.conf` [content mount][2] is a nifty detail of Infix that
-> `mywifi` (or any name you choose), which is then referenced in the WiFi
+> allows you to keep all the relevant configuration in a single file.
-> configuration. The country-code must match your location for regulatory
+> The deta is "simply" `base64` encoded, so you do not really need the
-> compliance (e.g., US, SE, DE, JP).
+> features of the Infix CLI, everything can be set up remotely [using
+> `curl`][3] if you like.
 
-### Touch Screen Support
+### Pre-built images
 
-The [Raspberry Pi Touch Display v1][10] (800x480 resolution) is supported on
+Pre-built SD card images are available here: [infix-rpi64-sdcard.img][sdcard]
-the Pi 4B, including touch functionality. To use graphical applications with
-the touch screen, you need to run them in a container with proper device
-access.
 
-#### Requirements for Graphical Applications
+[0]: https://www.raspberrypi.com/products/raspberry-pi-touch-display/
-
+[1]: https://github.com/kernelkit/infix/releases/download/latest-boot/infix-rpi64-sdcard.img
-Containers need:
+[2]: https://kernelkit.org/infix/latest/container/#content-mounts
-- Access to `/dev/dri/` for graphics card access
+[3]: https://kernelkit.org/infix/latest/scripting-restconf/
-- Access to `/run/udev` for input device detection
-- Privileged mode or specific capabilities
-
-#### Example: Running Doom with Touch Screen
-
-```
-admin@infix:/> configure
-admin@infix:/config/> edit container doom
-admin@infix:/config/container/doom/> set image docker://mattiaswal/alpine-doom:latest
-admin@infix:/config/container/doom/> set privileged
-admin@infix:/config/container/doom/> edit mount udev
-admin@infix:/config/container/…/udev/> set type bind
-admin@infix:/config/container/…/udev/> set target /run/udev/
-admin@infix:/config/container/…/udev/> set source /run/udev/
-admin@infix:/config/container/…/udev/> end
-admin@infix:/config/container/doom/> edit mount xorg.conf
-admin@infix:/config/container/…/xorg.conf/> set content U2VjdGlvbiAiT3V0cHV0Q2xhc3MiCiAgSWRlbnRpZmllciAidmM0IgogIE1hdGNoRHJpdmVyICJ2YzQiCiAgRHJpdmVyICJtb2Rlc2V0dGluZyIKICBPcHRpb24gIlByaW1hcnlHUFUiICJ0cnVlIgpFbmRTZWN0aW9uCg==
-admin@infix:/config/container/…/xorg.conf/> set target /etc/X11/xorg.conf
-admin@infix:/config/container/…/xorg.conf/> end
-admin@infix:/config/container/doom/> edit volume var
-admin@infix:/config/container/…/var/> set target /var
-admin@infix:/config/container/…/var/> leave
-```
-
-> [!NOTE]
-> The `xorg.conf` [content mount][3] is a useful Infix feature that allows you
-> to keep all configuration in a single file. The data is base64 encoded, and
-> everything can be set up remotely [using `curl`][4] if preferred.
-
-### Power Supply Requirements
-
-Proper power supply is critical for stable operation:
-
-- **Raspberry Pi 4B:** 5V/3A USB-C power supply (official recommended)
-- **Raspberry Pi 3B:** 5V/2.5A micro-USB power supply
-- **Compute Module 4:** Power requirements depend on carrier board
-
-Inadequate power can cause:
-- Random reboots or crashes
-- USB device failures
-- Network disconnections
-- Corrupted storage
-
-<img align="right" src="gpio-pinout.png" alt="GPIO Pinout" width=300 padding=10>
-
-### Serial Console Access (Optional)
-
-A serial console is useful for debugging but not required for Pi 3B/4B, since
-the factory configuration enables network access via DHCP. For CM4 and other
-variants without factory configuration, serial console access is required for
-initial setup.
-
-To connect via serial:
-
-1. Connect a USB-to-TTL serial adapter (3.3V) to GPIO pins:
-   - GND (black wire) → Pin 6 (Ground)
-   - TX → Pin 8 (GPIO 14, RXD)
-   - RX → Pin 10 (GPIO 15, TXD)
-   - **VCC (red wire) → Leave disconnected** (Pi has its own power supply)
-2. Use 115200 baud, 8 data bits, no parity, 1 stop bit (115200 8N1)
-3. Connect using `screen`, `minicom`, or similar terminal emulator
-
-The image shows the standard 40-pin GPIO header pinout. For serial console:
-- **Pin 6** (black) = Ground
-- **Pin 8** (orange) = TxD (UART) - connect to RX on your adapter
-- **Pin 10** (orange) = RxD (UART) - connect to TX on your adapter
-
-> [!WARNING]
-> Use only 3.3V serial adapters. 5V adapters will damage your Raspberry Pi!
-
-## Troubleshooting
-
-### Board won't boot
-
-- Verify the power supply meets requirements (see [Power Supply Requirements](#power-supply-requirements))
-- Check that the SD card is properly seated
-- Try re-flashing the SD card image
-- Look for the green LED activity indicator (should flash during boot)
-- Connect via serial console to see boot messages if needed
-
-### Can't find IP address
-
-- Ensure Ethernet cable is properly connected (look for link LED activity)
-- Verify your DHCP server is running and has available addresses
-- Check your router/DHCP server's client list for new devices
-- Use `nmap` or `arp-scan` to scan your network
-- Connect via serial console and run `ip addr` to see the assigned address
-
-### WiFi not working
-
-- Verify WiFi regulatory domain is set correctly
-- Check that SSID and password are correct
-- Ensure WiFi channel is supported in your region
-- Try connecting to a 2.4 GHz network first (better compatibility)
-
-### SD card corruption
-
-If the system becomes unresponsive or won't boot:
-
-- Always use proper shutdown procedures (don't just pull power)
-- Use a quality SD card (Class 10, A1, or better recommended)
-- Consider using a UPS or battery backup for critical deployments
-- Verify power supply meets requirements (see [Power Supply Requirements](#power-supply-requirements))
-
-### Container/Docker issues
-
-- Verify adequate RAM is available (check with `free -h`)
-- Ensure sufficient SD card space (check with `df -h`)
-- For Pi 3B, consider using lighter containers due to limited RAM
-
-## Additional Resources
-
-- [Infix Documentation][1]
-- [Flashing SD Card Guide][0]
-- [Infix Container Documentation][3]
-- [Scripting with RESTCONF][4]
-- [Release Downloads][8]
-- [Official Raspberry Pi Documentation][11]
-
-## Building Custom Images
-
-See the main Infix documentation for building from source. To build a custom
-Raspberry Pi image:
-
-```bash
-# Build the bootloader (only needed once or when bootloader changes)
-make O=x-boot rpi64_boot_defconfig
-make O=x-boot
-
-# Build main system
-make aarch64_defconfig
-make
-
-# Create SD card image
-./utils/mkimage.sh -od raspberrypi-rpi64
-```
-
-The resulting image will be in `output/images/infix-rpi64-sdcard.img`.
-
-### Customizing the Build
-
-You can customize the build by:
-- Modifying `board/aarch64/raspberrypi-rpi64/config.txt` for boot configuration
-- Adding packages to the Buildroot configuration
-- Customizing the device tree in `board/aarch64/raspberrypi-rpi64/dts/`
-
-## Performance Notes
-
-### Raspberry Pi 4B vs 3B
-
-The Pi 4B offers significant improvements over the 3B:
-- 3x faster processor
-- Up to 8x more RAM
-- Gigabit Ethernet (vs 100 Mbps)
-- USB 3.0 for faster storage and peripherals
-- Better thermal performance
-
-For network-intensive applications, the Pi 4B is strongly recommended.
-
-### Raspberry Pi as a Router
-
-While capable of basic routing tasks, be aware of limitations:
-- Single Ethernet port (consider USB Ethernet adapters for multi-port setups)
-- CPU-based packet processing (no hardware offload)
-- Best suited for home/lab use rather than high-throughput production
-
-For applications requiring multiple ports or high performance, consider
-dedicated networking hardware like the [Banana Pi R3][12].
-
-[0]: https://kernelkit.org/posts/flashing-sdcard/
-[1]: https://kernelkit.org/infix/latest/
-[2]: https://github.com/kernelkit/infix/releases/download/latest-boot/infix-rpi64-sdcard.img
-[3]: https://kernelkit.org/infix/latest/container/#content-mounts
-[4]: https://kernelkit.org/infix/latest/scripting-restconf/
-[8]: https://github.com/kernelkit/infix/releases/tag/latest-boot
-[9]: https://kernelkit.org/infix/latest/networking/#wifi
-[10]: https://www.raspberrypi.com/products/raspberry-pi-touch-display/
-[11]: https://www.raspberrypi.com/documentation/
-[12]: https://kernelkit.org/infix/latest/hardware/#banana-pi-bpi-r3

board/aarch64/raspberrypi-rpi64/config.txt

@@ -1,9 +1,3 @@
-# Raspberry Pi bootloader (start.elf) configuration
-#
-# uart_2ndstage=1 - Enable early boot debug output from the bootloader
-#                   Useful for debugging boot failures before U-Boot starts
-#                   Comment out for production to reduce boot noise
-
 [all]
 arm_64bit=1
 
@@ -18,7 +12,7 @@ dtoverlay=infix-key
 disable_overscan=1
 
 enable_uart=1
-#uart_2ndstage=1
+uart_2ndstage=1
 
 [pi3]
 start_file=start.elf

board/aarch64/raspberrypi-rpi64/rootfs/usr/share/product/raspberrypi,4-model-b/etc/factory-config.cfg

@@ -47,8 +47,7 @@
               {"id": "domain"},
               {"id": "hostname"},
               {"id": "dns-server"},
-              {"id": "ntp-server"},
+              {"id": "ntp-server"}
-              {"id": "vendor-class", "value": "Raspberry Pi 4 Model B"}
             ]
           }
         }

board/aarch64/raspberrypi-rpi64/rootfs/usr/share/product/raspberrypi,4-model-b/usr/libexec/confd/product/gen-interfaces

@@ -0,0 +1,6 @@
+cat <<EOF
+   {
+        "name": "wifi0",
+        "type": "infix-if-type:wifi",
+   }
+EOF

board/board.mk

@@ -1,3 +1,2 @@
-include $(BR2_EXTERNAL_INFIX_PATH)/board/common/common.mk
 include $(BR2_EXTERNAL_INFIX_PATH)/board/ix-board.mk
--include $(BR2_EXTERNAL_INFIX_PATH)/board/$(patsubst "%",%,$(BR2_ARCH))/board.mk
+include $(sort $(wildcard $(BR2_EXTERNAL_INFIX_PATH)/board/*/*/*.mk))

board/common/Config.in

@@ -1,28 +1,32 @@
-menu "Images"
+menuconfig SIGN_ENABLED
-
+	bool "Image Signing"
-source "$BR2_EXTERNAL_INFIX_PATH/board/common/image/image-itb-rootfs/Config.in"
-source "$BR2_EXTERNAL_INFIX_PATH/board/common/image/image-itb-aux/Config.in"
-source "$BR2_EXTERNAL_INFIX_PATH/board/common/image/image-itb-qcow/Config.in"
-source "$BR2_EXTERNAL_INFIX_PATH/board/common/image/image-itb-gns3a/Config.in"
-source "$BR2_EXTERNAL_INFIX_PATH/board/common/image/image-itb-rauc/Config.in"
-source "$BR2_EXTERNAL_INFIX_PATH/board/common/image/image-itb-dl-release/Config.in"
-source "$BR2_EXTERNAL_INFIX_PATH/board/common/image/image-readme/Config.in"
-
-endmenu
-
-config QEMU_SCRIPTS
-	bool "QEMU scripts"
 	default y
-	help
+
-	  Install QEMU scripts and related files in the images
+choice
-	  directory, which can be used to launch virtual Infix
+	prompt "Signing key source"
-	  instances.
+	depends on SIGN_ENABLED
+	default SIGN_SRC_DIR
+
+config SIGN_SRC_DIR
+	bool "Directory"
+
+config SIGN_SRC_PKCS11
+	bool "PKCS#11 URL"
+
+endchoice
+
+config SIGN_KEY
+	string "Signing key"
+	depends on SIGN_ENABLED
+	default "${BR2_EXTERNAL_INFIX_PATH}/board/common/signing-keys/development"  if SIGN_SRC_DIR
 
 menuconfig TRUSTED_KEYS
 	bool "Trusted keys for image"
+	depends on SIGN_ENABLED
 	help
 	 Keys that will be accepted for this image
 
+
 config TRUSTED_KEYS_DEVELOPMENT
 	bool "Development key"
 	depends on TRUSTED_KEYS
@@ -35,3 +39,130 @@ config TRUSTED_KEYS_DEVELOPMENT_PATH
 config TRUSTED_KEYS_EXTRA_PATH
 	string "Path to extra keys to include in image"
 	depends on TRUSTED_KEYS
+
+menuconfig DISK_IMAGE
+	bool "Disk image"
+	help
+	  Compose a full disk image with redundant Linux OS partitions,
+	  configuration partition, etc.
+
+	  This is useful when:
+	  - Bringing up a blank system during manufacturing
+	  - Creating a GNS3 appliance
+	  - Developing/debugging issues in the boot process in QEMU
+
+menuconfig DISK_IMAGE_SIZE
+	string "Image size"
+	depends on DISK_IMAGE
+	default "512M"
+	help
+	  Create a disk image of this size.  A K/M/G suffix may be used
+	  to multiply by powers of 1024.  Suffixes like KB/MB/GB may be
+	  used to multiply by powers of 1000.  The image will be split
+	  proportionally to fit the two rootfs, a kernel, a writable
+	  /cfg and /var partiotions.
+
+	  Minimum supported size is 512M.
+
+choice
+	prompt "Bootloader"
+	depends on DISK_IMAGE
+	default DISK_IMAGE_BOOT_EFI if BR2_x86_64
+	default DISK_IMAGE_BOOT_NONE
+
+config DISK_IMAGE_BOOT_NONE
+	bool "None"
+	help
+	  Do not create any bootloader partition in the disk image.
+
+config DISK_IMAGE_BOOT_EFI
+	bool "EFI"
+	help
+	  Create a boot partition from a directory containing an EFI
+	  boot application, e.g. GRUB.
+
+config DISK_IMAGE_BOOT_BIN
+	bool "Binary"
+	help
+	  Create a boot partition from a raw image containing the boot
+	  application, e.g. U-Boot.
+
+endchoice
+
+config DISK_IMAGE_BOOT_DATA
+	string "Bootloader data"
+	depends on DISK_IMAGE
+	depends on DISK_IMAGE_BOOT_EFI || DISK_IMAGE_BOOT_BIN
+	default "${BINARIES_DIR}/efi-part/EFI" if BR2_x86_64
+	help
+	  Path to the directory or file holding the bootloader data.
+
+config DISK_IMAGE_BOOT_OFFSET
+	hex "Bootloader offset"
+	depends on DISK_IMAGE
+	depends on DISK_IMAGE_BOOT_EFI || DISK_IMAGE_BOOT_BIN
+	default 0x8000
+	help
+	  Offset at which the bootloader partition is placed. Remember
+	  to make sure that the GPT still fits at the start of the
+	  image.
+
+config DISK_IMAGE_RELEASE_URL
+	string "Infix URL"
+	depends on DISK_IMAGE
+	depends on !BR2_TARGET_ROOTFS_SQUASHFS
+	default "https://github.com/kernelkit/infix/releases/download/latest/infix-${BR2_ARCH}.tar.gz"
+	help
+	  In situations where Infix itself is not being built, but a
+	  disk image is, i.e. when building a bootloader: place this
+	  Infix release in the primary and secondary partitions.
+
+menuconfig GNS3_APPLIANCE
+	bool "GNS3 Appliance"
+	select DISK_IMAGE
+	default y
+	help
+	  Create a GNS3 appliance description that, together with the
+	  disk image, can be imported into GNS3.
+
+config GNS3_APPLIANCE_RAM
+	int "Reserved RAM (MiB)"
+	depends on GNS3_APPLIANCE
+	default "192"
+	help
+	  Amount of host RAM reserved for an appliance instance.
+
+	  Minimum supported size is 192M.
+
+config GNS3_APPLIANCE_IFNUM
+	int "Number of interfaces"
+	depends on GNS3_APPLIANCE
+	default "1"
+	help
+	  Number of Ethernet interfaces to create for an appliance instance.
+
+menuconfig FIT_IMAGE
+	bool "Traditional FIT image"
+	help
+	  Create a "regular" FIT image where the kernel and DTBs are
+	  stored in the FIT rather than inside the rootfs (like it
+	  normally is in Infix).
+
+	  This is useful when trying out Infix on targets whose
+	  bootloader might not be capable of booting a raw Squash, but
+	  is able to handle an FIT.
+
+config FIT_ARCH
+	string
+	depends on FIT_IMAGE
+	default "arm64" if BR2_aarch64
+
+config FIT_KERNEL_LOAD_ADDR
+	string "Kernel load address"
+	depends on FIT_IMAGE
+
+config SDCARD_AUX
+	bool "Create SD-card aux partition"
+	help
+	  Create and populate aux.ext4 with rootfs.itbh and rauc.status
+	  For use with a static genimage.cfg for, e.g., SD-cards.

board/common/common.mk

@@ -1,7 +1,4 @@
-include $(BR2_EXTERNAL_INFIX_PATH)/board/common/image/image.mk
+ifeq ($(SIGN_ENABLED),y)
-include $(BR2_EXTERNAL_INFIX_PATH)/board/common/qemu/qemu.mk
-
-ifeq ($(TRUSTED_KEYS),y)
 include $(BR2_EXTERNAL_INFIX_PATH)/board/common/uboot/uboot.mk
 
 TRUSTED_KEYS=$(TRUSTED_KEYS_DEVELOPMENT_PATH) $(TRUSTED_KEYS_EXTRA_PATH)

board/common/genimage.cfg.in

@@ -1,5 +1,16 @@
 @BOOTIMG@
 
+image aux.ext4 {
+	mountpoint = "/aux"
+	temporary = true
+	size = @AUXSIZE@
+
+	ext4 {
+		label = "aux"
+		use-mke2fs = true
+	}
+}
+
 image cfg.ext4 {
 	empty = true
 	temporary = true
@@ -22,8 +33,7 @@ image var.ext4 {
 	}
 }
 
-image disk.img {
+image @DISKIMG@ {
-	temporary = true
 	size = @TOTALSIZE@
 	hdimage {
 		partition-table-type = "gpt"
@@ -58,15 +68,5 @@ image disk.img {
 	}
 }
 
-image @QCOWIMG@ {
-	qemu {
-		format = "qcow2"
-	}
-
-	partition disk {
-		image = "disk.img"
-	}
-}
-
 # Silence genimage warnings
 config {}

board/common/image/image-itb-aux/Config.in

@@ -1,10 +0,0 @@
-config IMAGE_ITB_AUX
-	bool "aux partition"
-	depends on IMAGE_ITB_ROOTFS
-	select BR2_PACKAGE_HOST_UBOOT_TOOLS
-	select BR2_PACKAGE_HOST_GENIMAGE
-	help
-	  Create and populate auxiliary partition, aux.ext4, with
-	  metadata needed by U-Boot and RAUC to operate properly on
-	  systems using ITB images. This may then be included as a
-	  partition in a larger disk image.

board/common/image/image-itb-aux/generate.sh

@@ -1,85 +0,0 @@
-#!/bin/sh
-
-set -e
-
-boot="${1}"
-squash="${BINARIES_DIR}"/rootfs.squashfs
-itbh="${BINARIES_DIR}"/rootfs.itbh
-aux="${BINARIES_DIR}"/aux.ext4
-
-mkdir -p "${WORKDIR}"/aux
-rm -rf   "${WORKDIR}"/tmp
-mkdir -p "${WORKDIR}"/tmp
-
-cp -f "${itbh}" "${WORKDIR}"/aux/primary.itbh
-cp -f "${itbh}" "${WORKDIR}"/aux/secondary.itbh
-
-tstamp=$(date -u +%FT%TZ)
-rootsha=$(sha256sum "${squash}" | cut -d" " -f1)
-rootsize=$(stat -c %s "${squash}")
-cat <<EOF >"${WORKDIR}"/aux/rauc.status
-[slot.rootfs.0]
-bundle.compatible=${COMPATIBLE}
-bundle.version=${VERSION}
-status=ok
-sha256=${rootsha}
-size=${rootsize}
-installed.timestamp=$tstamp
-installed.count=1
-activated.timestamp=$tstamp
-activated.count=1
-
-[slot.rootfs.1]
-bundle.compatible=${COMPATIBLE}
-bundle.version=${VERSION}
-status=ok
-sha256=${rootsha}
-size=${rootsize}
-installed.timestamp=$tstamp
-installed.count=1
-activated.timestamp=$tstamp
-activated.count=1
-EOF
-
-case "${boot}" in
-    uboot)
-	cat <<EOF | mkenvimage -s 0x4000 -o "${WORKDIR}"/aux/uboot.env -
-BOOT_ORDER=primary secondary net
-BOOT_primary_LEFT=1
-BOOT_secondary_LEFT=1
-BOOT_net_LEFT=1
-EOF
-	;;
-    grub)
-	mkdir -p "${WORKDIR}"/aux/grub
-	cp -f "${PKGDIR}"/grub.cfg "${PKGDIR}"/grubenv "${WORKDIR}"/aux/grub
-	;;
-    *)
-	echo "UNSUPPORTED BOOTLOADER ${boot}" >&2
-	exit 1
-esac
-
-cat <<EOF >"${WORKDIR}"/genimage.cfg
-image $(basename ${aux}) {
-	mountpoint = "/"
-	size = 8M
-
-	ext4 {
-		label = "aux"
-		use-mke2fs = true
-		features = "^metadata_csum,^metadata_csum_seed,uninit_bg"
-                extraargs = "-m 0 -i 4096"
-	}
-}
-
-# Silence genimage warnings
-config {}
-EOF
-
-genimage \
-    --loglevel 1 \
-    --tmppath    "${WORKDIR}"/tmp \
-    --rootpath   "${WORKDIR}"/aux \
-    --inputpath  "${WORKDIR}" \
-    --outputpath "$(dirname ${aux})" \
-    --config     "${WORKDIR}"/genimage.cfg

board/common/image/image-itb-aux/grub.cfg

@@ -1,80 +0,0 @@
-set timeout="1"
-
-load_env ORDER DEBUG
-
-if [ -z "$ORDER" ]; then
-    set ORDER="primary secondary"
-fi
-
-set ORDER="$ORDER reboot"
-
-for slot in $ORDER; do
-    if [ -z "$default" ]; then
-        set default="$slot"
-    else
-        # Contrary to what the documentation says, GRUB (2.06) does
-        # not support using titles or IDs in the fallback variable, so
-        # we translate to indices.
-        if [ "$slot" = "primary" ]; then
-            set fallback="$fallback 0"
-        elif [ "$slot" = "secondary" ]; then
-            set fallback="$fallback 1"
-        elif [ "$slot" = "net" ]; then
-            set fallback="$fallback 2"
-        elif [ "$slot" = "reboot" ]; then
-            set fallback="$fallback 3"
-	fi
-    fi
-done
-
-if [ "$DEBUG" ]; then
-    set log="debug"
-else
-    set log="loglevel=4"
-fi
-
-# From board/common/rootfs/etc/partition-uuid
-search -p 107ae911-a97b-4380-975c-7ce1a2dde1e0 --set primary
-search -p 352bd9b2-2ca9-44e2-bdc7-edbc87ba1e02 --set secondary
-
-export primary
-export secondary
-
-submenu "primary" "$log" {
-    set slot="$1"
-    set append="console=ttyS0 console=hvc0 usbcore.authorized_default=2 root=PARTLABEL=$slot $2"
-    set root="($primary)"
-    source /boot/grub/grub.cfg
-}
-
-submenu "secondary" "$log"  {
-    set slot="$1"
-    set append="console=ttyS0 console=hvc0 usbcore.authorized_default=2 root=PARTLABEL=$slot $2"
-    set root="($secondary)"
-    source /boot/grub/grub.cfg
-}
-
-submenu "net" "$log"  {
-    net_dhcp
-
-    if [ "$net_efinet0_dhcp_next_server" -a "$net_efinet0_dhcp_boot_file" ]; then
-	set initrd=(tftp,$net_efinet0_dhcp_next_server)/$net_efinet0_dhcp_boot_file
-	loopback initrd $initrd
-	set root=(initrd)
-
-	set slot="$1"
-	set append="console=ttyS0 console=hvc0 usbcore.authorized_default=2 qroot=/dev/ram0 ramdisk_size=65536 $2"
-	source /boot/grub/grub.cfg
-    else
-	if [ -z "$net_efinet0_dhcp_next_server" ]; then
-	    echo "No TFTP server supplied in DHCP response"
-	fi
-	if [ -z "$net_efinet0_dhcp_boot_file" ]; then
-	    echo "No bootfile supplied in DHCP response"
-	fi
-    fi
-}
-
-submenu "reboot" {
-    reboot
-}

board/common/image/image-itb-aux/grubenv

@@ -1,10 +0,0 @@
-# GRUB Environment Block
-# WARNING: Do not edit this file by tools other than grub-editenv!!!
-ORDER=primary secondary net
-primary_OK=1
-secondary_OK=1
-net_OK=1
-primary_TRY=0
-secondary_TRY=0
-net_TRY=0
-#########################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################

board/common/image/image-itb-aux/image-itb-aux.mk

@@ -1,10 +0,0 @@
-################################################################################
-#
-# image-itb-aux
-#
-################################################################################
-
-IMAGE_ITB_AUX_DEPENDENCIES := host-uboot-tools host-genimage image-itb-rootfs
-IMAGE_ITB_AUX_OPTS := $(if $(BR2_TARGET_GRUB2),grub,uboot)
-
-$(eval $(ix-image))

board/common/image/image-itb-dl-release/Config.in

@@ -1,15 +0,0 @@
-menuconfig IMAGE_ITB_DL_RELEASE
-	bool "Download existing release"
-	depends on !BR2_TARGET_ROOTFS_SQUASHFS
-	help
-	  This is primarily used by target specific builds, where the
-	  bootloader artifact needs to be combined with an existing
-	  Infix image, to create a full disk image that can be
-	  provisioned to an SD-card or eMMC.
-
-config IMAGE_ITB_DL_RELEASE_URL
-	string "URL"
-	depends on IMAGE_ITB_DL_RELEASE
-	default "https://github.com/kernelkit/infix/releases/download/latest/infix-${BR2_ARCH}.tar.gz"
-	help
-	  URL to release tarball.

board/common/image/image-itb-dl-release/generate.sh

@@ -1,25 +0,0 @@
-#!/bin/sh
-
-set -e
-
-squash="${BINARIES_DIR}"/rootfs.squashfs
-aux="${BINARIES_DIR}"/aux.ext4
-
-[ -f "${squash}" ] && [ -f "${aux}" ] && exit 0
-
-archive="${WORKDIR}/$(basename ${URL})"
-[ -f "${archive}" ] || wget -O"${archive}" "${URL}"
-
-echo "Unpacking..."
-tar -xa --strip-components=1 -C "${BINARIES_DIR}" -f "${archive}"
-
-auxsize=$(stat -c %s "${aux}")
-if [ "${auxsize}" -gt $((8 << 20)) ]; then
-    # In older releases, 16M aux.ext4 images were generated. In order
-    # to keep the image-itb-qcow logic simpler, trim it 8M, which we
-    # always generate nowadays.
-    echo "WARNING: Auxiliary partition is unexpectedly large. Resizing..."
-    resize2fs "${aux}" 8M
-    truncate -s 8M "${aux}"
-    tune2fs -l "${aux}"
-fi

board/common/image/image-itb-dl-release/image-itb-dl-release.mk

@@ -1,9 +0,0 @@
-################################################################################
-#
-# image-itb-dl-release
-#
-################################################################################
-
-IMAGE_ITB_DL_RELEASE_CONFIG_VARS := URL
-
-$(eval $(ix-image))

board/common/image/image-itb-gns3a/Config.in

@@ -1,23 +0,0 @@
-menuconfig IMAGE_ITB_GNS3A
-	bool "GNS3 Appliance (ITB)"
-	depends on BR2_x86_64
-	select IMAGE_ITB_QCOW
-	help
-	  Create a GNS3 appliance description that, together with the
-	  disk image, can be imported into GNS3.
-
-config IMAGE_ITB_GNS3A_RAM
-	int "Reserved RAM (MiB)"
-	depends on IMAGE_ITB_GNS3A
-	default "192"
-	help
-	  Amount of host RAM reserved for an appliance instance.
-
-	  Minimum supported size is 192M.
-
-config IMAGE_ITB_GNS3A_IFNUM
-	int "Number of interfaces"
-	depends on IMAGE_ITB_GNS3A
-	default "1"
-	help
-	  Number of Ethernet interfaces to create for an appliance instance.

board/common/image/image-itb-gns3a/generate.sh

@@ -1,59 +0,0 @@
-#!/bin/sh
-
-set -e
-
-bios="${BINARIES_DIR}"/OVMF.fd
-qcow="${BINARIES_DIR}"/"${ARTIFACT}".qcow2
-gns3a="${BINARIES_DIR}"/"${ARTIFACT}".gns3a
-
-cat <<EOF >"${gns3a}"
-{
-    "name": "${ARTIFACT} devel",
-    "category": "router",
-    "description": "${ARTIFACT} development appliance",
-    "vendor_name": "Kernelkit",
-    "vendor_url": "https://kernelkit.org",
-    "product_name": "${ARTIFACT} devel",
-    "registry_version": 6,
-    "status": "experimental",
-    "maintainer": "Kernelkit",
-    "maintainer_email": "null@kernelkit.org",
-    "usage": "Default login, user/pass: admin/admin\n\nType 'cli' (and Enter) followed by 'help' for an overview of commands and relevant configuration files.",
-    "port_name_format": "eth{0}",
-    "linked_clone": true,
-    "qemu": {
-        "adapter_type": "virtio-net-pci",
-        "adapters": ${IFNUM},
-        "ram": ${RAM},
-        "cpus": 1,
-        "hda_disk_interface": "virtio",
-        "arch": "x86_64",
-        "console_type": "telnet",
-        "bios_image": "$(basename ${bios})",
-        "kvm": "allow"
-    },
-    "images": [
-        {
-            "filename": "$(basename "${bios}")",
-            "filesize": $(stat --printf='%s' "${bios}"),
-            "md5sum": "$(md5sum "${bios}" | awk '{print $1}')",
-            "version": "0.0"
-        },
-        {
-            "filename": "$(basename "${qcow}")",
-            "filesize": $(stat --printf='%s' "${qcow}"),
-            "md5sum": "$(md5sum "${qcow}" | awk '{print $1}')",
-            "version": "${VERSION}"
-        }
-    ],
-    "versions": [
-        {
-            "name": "${VERSION}",
-            "images": {
-                "bios_image": "$(basename ${bios})",
-                "hda_disk_image": "$(basename ${qcow})"
-            }
-        }
-    ]
-}
-EOF

board/common/image/image-itb-gns3a/image-itb-gns3a.mk

@@ -1,10 +0,0 @@
-################################################################################
-#
-# image-itb-gns3a
-#
-################################################################################
-
-IMAGE_ITB_GNS3A_DEPENDENCIES := image-itb-qcow
-IMAGE_ITB_GNS3A_CONFIG_VARS  := IFNUM RAM
-
-$(eval $(ix-image))

board/common/image/image-itb-qcow/Config.in

@@ -1,68 +0,0 @@
-menuconfig IMAGE_ITB_QCOW
-	bool "QEMU disk image (ITB)"
-	depends on (IMAGE_ITB_ROOTFS && IMAGE_ITB_AUX) || IMAGE_ITB_DL_RELEASE
-	select BR2_PACKAGE_HOST_GENIMAGE
-	help
-	  Compose a full disk image with redundant Linux OS partitions,
-	  configuration partition, etc., for systems using ITB images.
-
-	  This is useful when:
-	  - Bringing up a blank system during manufacturing
-	  - Creating a GNS3 appliance
-	  - Developing/debugging issues in the boot process in QEMU
-
-menuconfig IMAGE_ITB_QCOW_SIZE
-	string "Image size"
-	depends on IMAGE_ITB_QCOW
-	default "512M"
-	help
-	  Create a disk image of this size.  A K/M/G suffix may be used
-	  to multiply by powers of 1024.  Suffixes like KB/MB/GB may be
-	  used to multiply by powers of 1000.  The image will be split
-	  proportionally to fit the two rootfs, a kernel, a writable
-	  /cfg and /var partiotions.
-
-	  Minimum supported size is 512M.
-
-choice
-	prompt "Bootloader"
-	depends on IMAGE_ITB_QCOW
-	default IMAGE_ITB_QCOW_BOOT_EFI if BR2_x86_64
-	default IMAGE_ITB_QCOW_BOOT_NONE
-
-config IMAGE_ITB_QCOW_BOOT_NONE
-	bool "None"
-	help
-	  Do not create any bootloader partition in the disk image.
-
-config IMAGE_ITB_QCOW_BOOT_EFI
-	bool "EFI"
-	help
-	  Create a boot partition from a directory containing an EFI
-	  boot application, e.g. GRUB.
-
-config IMAGE_ITB_QCOW_BOOT_BIN
-	bool "Binary"
-	help
-	  Create a boot partition from a raw image containing the boot
-	  application, e.g. U-Boot.
-
-endchoice
-
-config IMAGE_ITB_QCOW_BOOT_DATA
-	string "Bootloader data"
-	depends on IMAGE_ITB_QCOW
-	depends on IMAGE_ITB_QCOW_BOOT_EFI || IMAGE_ITB_QCOW_BOOT_BIN
-	default "${BINARIES_DIR}/efi-part/EFI" if BR2_x86_64
-	help
-	  Path to the directory or file holding the bootloader data.
-
-config IMAGE_ITB_QCOW_BOOT_OFFSET
-	hex "Bootloader offset"
-	depends on IMAGE_ITB_QCOW
-	depends on IMAGE_ITB_QCOW_BOOT_EFI || IMAGE_ITB_QCOW_BOOT_BIN
-	default 0x8000
-	help
-	  Offset at which the bootloader partition is placed. Remember
-	  to make sure that the GPT still fits at the start of the
-	  image.

board/common/image/image-itb-qcow/image-itb-qcow.mk

@@ -1,15 +0,0 @@
-################################################################################
-#
-# image-itb-qcow
-#
-################################################################################
-
-# We can source the rootfs+aux from a local build, or from a
-# downloaded release; so adjust our dependencies accordingly.
-IMAGE_ITB_QCOW_SRC-$(IMAGE_ITB_ROOTFS)     := image-itb-rootfs image-itb-aux
-IMAGE_ITB_QCOW_SRC-$(IMAGE_ITB_DL_RELEASE) := image-itb-dl-release
-
-IMAGE_ITB_QCOW_DEPENDENCIES := host-genimage $(IMAGE_ITB_QCOW_SRC-y)
-IMAGE_ITB_QCOW_CONFIG_VARS := BOOT_DATA BOOT_OFFSET SIZE
-
-$(eval $(ix-image))

board/common/image/image-itb-rauc/Config.in

@@ -1,27 +0,0 @@
-menuconfig IMAGE_ITB_RAUC
-	bool "RAUC upgrade bundle (ITB)"
-	select IMAGE_ITB_ROOTFS
-	select BR2_PACKAGE_HOST_RAUC
-	help
-	  Create RAUC upgrade bundle, for targets using ITB images,
-	  that can be used to upgrade a running system to this version
-	  of Infix.
-
-config IMAGE_ITB_RAUC_KEY
-	string "signing key"
-	depends on IMAGE_ITB_RAUC
-	default "${BR2_EXTERNAL_INFIX_PATH}/board/common/signing-keys/development/infix.key"
-	help
-	  Path to the private key, in PKCS#8 format, used to sign
-	  the RAUC bundle; or a PKCS#11 URI.
-
-config IMAGE_ITB_RAUC_CERT
-	string "signing certificate"
-	depends on IMAGE_ITB_RAUC
-	default "${BR2_EXTERNAL_INFIX_PATH}/board/common/signing-keys/development/infix.crt"
-	help
-	  Path to the X509 certificate which will be associated with
-	  the bundle signature.
-
-	  NOTE: This cert MUST be included in the trust store of the
-	        system on which this bundle is to be installed.

board/common/image/image-itb-rauc/generate.sh

@@ -1,35 +0,0 @@
-#!/bin/sh
-
-set -e
-
-squash="${BINARIES_DIR}"/rootfs.squashfs
-itbh="${BINARIES_DIR}"/rootfs.itbh
-pkg="${BINARIES_DIR}"/"${ARTIFACT}.pkg"
-
-cp -f "${PKGDIR}"/hooks.sh "${WORKDIR}"/hooks.sh
-
-# RAUC internally uses the file extension to find a suitable install
-# handler, hence the name must be .img
-cp -f "${squash}" "${WORKDIR}"/rootfs.img
-cp -f "${itbh}"   "${WORKDIR}"/rootfs.itbh
-
-cat >"${WORKDIR}"/manifest.raucm <<EOF
-[update]
-compatible=${COMPATIBLE}
-version=${VERSION}
-
-[bundle]
-format=verity
-
-[hooks]
-filename=hooks.sh
-
-[image.rootfs]
-filename=rootfs.img
-hooks=post-install
-EOF
-
-rauc --cert="${CERT}" --key="${KEY}" \
-     bundle "${WORKDIR}" "${pkg}.next"
-
-mv "${pkg}.next" "${pkg}"

board/common/image/image-itb-rauc/image-itb-rauc.mk

@@ -1,10 +0,0 @@
-################################################################################
-#
-# image-itb-rauc
-#
-################################################################################
-
-IMAGE_ITB_RAUC_DEPENDENCIES := host-rauc image-itb-rootfs
-IMAGE_ITB_RAUC_CONFIG_VARS := KEY CERT
-
-$(eval $(ix-image))

board/common/image/image-itb-rootfs/Config.in

@@ -1,20 +0,0 @@
-menuconfig IMAGE_ITB_ROOTFS
-	bool "rootfs.itb+.itbh"
-	select BR2_TARGET_ROOTFS_SQUASHFS
-	select BR2_PACKAGE_HOST_UBOOT_TOOLS
-	help
-	  Create a signed ITB image containing a SquashFS of rootfs
-	  and extract detached header (.itbh) for U-Boot based
-	  targets.
-
-config IMAGE_ITB_ROOTFS_KEY
-	string "signing key"
-	depends on IMAGE_ITB_ROOTFS
-	default "${BR2_EXTERNAL_INFIX_PATH}/board/common/signing-keys/development/infix.key"
-	help
-	  Path to the private RSA key, in PKCS#8 format, used to sign
-	  the root filesystem.
-
-	  If the path is prefixed with "<hint>:", then that used as
-	  the "key-name-hint" in the resulting ITB, otherwise the
-	  basename of the path, with any extension removed, is used.

board/common/image/image-itb-rootfs/generate.sh

@@ -1,71 +0,0 @@
-#!/bin/sh
-
-set -e
-
-squash="${BINARIES_DIR}"/rootfs.squashfs
-
-itb="${BINARIES_DIR}"/rootfs.itb
-itbh_size=0x1000
-
-IFS=:
-set ${KEY}
-case $# in
-    1)
-	keyfile="$1"
-	hint=$(basename ${keyfile%.*})
-	;;
-    2)
-	keyfile="$2"
-	hint="$1"
-	;;
-    *)
-	echo "INVALID KEY" >&2
-	exit 1
-	;;
-esac
-
-rsanibbles=$(openssl rsa -in "${KEY}" -noout -modulus | \
-		 sed -e 's/^Modulus=//' | tr -d '\n' | wc -c)
-if [ "${rsanibbles}" -le 0 ]; then
-    echo "ONLY RSA KEYS ARE SUPPORTED" >&2
-    exit 1
-fi
-
-cat >"${WORKDIR}"/rootfs.its <<EOF
-/dts-v1/;
-
-/ {
-	description = "${ARTIFACT}";
-	creator = "infix";
-	#address-cells = <0x1>;
-
-	images {
-		rootfs {
-			description = "rootfs";
-			type = "ramdisk";
-			os = "linux";
-			compression = "none";
-			data = /incbin/("${squash}");
-			signature-1 {
-				algo = "sha256,rsa$((rsanibbles << 2))";
-				key-name-hint = "${hint}";
-			};
-		};
-	};
-
-	configurations {
-		default = "verity";
-		verity {
-			ramdisk = "rootfs";
-		};
-	};
-};
-
-EOF
-
-mkimage -E -p $itbh_size -B $itbh_size \
-	-f "${WORKDIR}"/rootfs.its \
-	-g "${hint}" -G "${keyfile}" \
-	"${itb}"
-
-dd if="${itb}" bs=$((itbh_size)) count=1 of="${itb}h" status=none

board/common/image/image-itb-rootfs/image-itb-rootfs.mk

@@ -1,10 +0,0 @@
-################################################################################
-#
-# image-itb-rootfs
-#
-################################################################################
-
-IMAGE_ITB_ROOTFS_DEPENDENCIES := rootfs-squashfs
-IMAGE_ITB_ROOTFS_CONFIG_VARS := KEY
-
-$(eval $(ix-image))

board/common/image/image-readme/Config.in

@@ -1,6 +0,0 @@
-config IMAGE_README
-	bool "Install README.md in images"
-	help
-	  Install a README.md with useful information about getting
-	  started with Infix in the images directory (thereby also
-	  including it in the resulting release tarball).

board/common/image/image-readme/image-readme.mk

@@ -1,18 +0,0 @@
-################################################################################
-#
-# image-readme
-#
-################################################################################
-
-IMAGE_README_DIR := $(pkgdir)
-
-image-readme: $(BINARIES_DIR)/README.md
-
-$(BINARIES_DIR)/README.md: $(IMAGE_README_DIR)/README.md
-	@$(call IXMSG,"Installing README.md")
-	@mkdir -p $(BINARIES_DIR)
-	@cp $< $@
-
-ifeq ($(IMAGE_README),y)
-TARGETS_ROOTFS += image-readme
-endif

board/common/image/image.mk

@@ -1,2 +0,0 @@
-include $(BR2_EXTERNAL_INFIX_PATH)/board/common/image/ix-image.mk
-include $(sort $(wildcard $(BR2_EXTERNAL_INFIX_PATH)/board/common/image/*/*.mk))

board/common/image/ix-image.mk

@@ -1,26 +0,0 @@
-define inner-ix-image
-
-$(2)_DIR := $$(pkgdir)
-
-$(1): $$($(2)_DEPENDENCIES)
-	@$$(call IXMSG,"$$(if $$($(2)_MESSAGE),$$($(2)_MESSAGE),Creating $(1))")
-	@mkdir -p $$(BUILD_DIR)/$(1)
-	@ \
-	PATH=$$(BR_PATH) \
-	PKGDIR=$$($(2)_DIR) \
-	WORKDIR=$$(BUILD_DIR)/$(1) \
-	BINARIES_DIR=$$(BINARIES_DIR) \
-	BR2_EXTERNAL_INFIX_PATH=$$(BR2_EXTERNAL_INFIX_PATH) \
-	ARTIFACT=$$(INFIX_ARTIFACT) \
-	COMPATIBLE=$$(INFIX_COMPATIBLE) \
-	VERSION=$$(INFIX_VERSION) \
-	$$(foreach var,$$($(2)_CONFIG_VARS),$$(var)=$$($(2)_$$(var)) ) \
-	$$($(2)_DIR)/generate.sh $$($(2)_OPTS)
-
-ifeq ($$($(2)),y)
-TARGETS_ROOTFS += $(1)
-endif
-
-endef
-
-ix-image = $(call inner-ix-image,$(pkgname),$(call UPPERCASE,$(pkgname)))

board/common/mkaux.sh

@@ -0,0 +1,40 @@
+#!/bin/sh
+
+rootdir=$BUILD_DIR/genimage.root
+tempdir=$BUILD_DIR/genimage.tmp
+
+cat <<EOF > /tmp/mkaux.cfg
+image aux.ext4 {
+	mountpoint = "/aux"
+	size = 16M
+
+	ext4 {
+		label = "aux"
+		use-mke2fs = true
+		features = "^metadata_csum,^metadata_csum_seed,uninit_bg"
+                extraargs = "-m 0 -i 4096"
+	}
+}
+
+# Silence genimage warnings
+config {}
+EOF
+
+rm -rf   "$rootdir/aux"
+mkdir -p "$rootdir/aux"
+cp -f "$BINARIES_DIR/rootfs.itbh" "$rootdir/aux/primary.itbh"
+cp -f "$BINARIES_DIR/rootfs.itbh" "$rootdir/aux/secondary.itbh"
+cp -f "$BINARIES_DIR/rauc.status" "$rootdir/aux/rauc.status"
+
+mkenvimage -s 0x4000 -o "$rootdir/aux/uboot.env" \
+	   "$BR2_EXTERNAL_INFIX_PATH/board/common/uboot/aux-env.txt"
+
+rm -rf "$BINARIES_DIR/aux.ext4"
+rm -rf "$tempdir"
+
+genimage \
+    --rootpath   "$rootdir" \
+    --tmppath    "$tempdir" \
+    --inputpath  "$BINARIES_DIR" \
+    --outputpath "$BINARIES_DIR" \
+    --config "/tmp/mkaux.cfg"

board/common/mkdisk.sh

@@ -1,6 +1,8 @@
 #!/bin/sh
 set -e
 
+. $BR2_EXTERNAL_INFIX_PATH/board/common/rootfs/etc/partition-uuid
+
 K=10
 M=20
 G=30
@@ -45,32 +47,43 @@ dimension()
 	exit 1
     fi
 
-    # Place aux right after the GPT...
+    # Size var to fit whatever is left over. Also reserve another 32K
-    auxoffs=$((32 << K))
+    # at the end to make room for the backup GPT.
+    varsize=$(($total - $auxsize - 2 * $imgsize - $cfgsize))
+    if [ "$bootoffs" ]; then
+	varsize=$(($varsize - $bootsize))
+    fi
+    varsize=$(($varsize - (32 << K)))
 
     if [ "$bootoffs" ]; then
-	if [ $((bootoffs)) -lt $((32 << K)) ]; then
+	# Align the end of the boot partition to an even MiB. E.g. if
-	    echo "Boot partition collides with GPT"
+	# boot was dimensioned to 4M, and bootoffs is 32K, then the
-	    exit 1
+	# final bootsize becomes 4M - 32K, meaning aux will start on
-	fi
+	# exactly 4M.
-
+	auxoffs=$bootsize
-	# ...unless we have a boot partition, in which case we place
+	bootsize=$(($bootsize - $bootoffs))
-	# it after that.
+    else
-	auxoffs=$((auxoffs + bootsize))
+	# No bootloader, place aux after GPT, resize it to end on an
+	# even MiB (as is done for boot above).
+	auxoffs=$((32 << K))
+	auxsize=$(($auxsize - $auxoffs))
     fi
+}
 
-    # Finally, size var to fit whatever is left over by subtracting
+probeboot()
-    # all other images, plus another 32K at the end for the backup
+{
-    # GPT.
+    # If we have built an EFI app, typically grub, make sure to
-    varsize=$((total - auxoffs - auxsize - 2 * imgsize - cfgsize - (32 << K)))
+    # include it.
+    if [ -d $BINARIES_DIR/efi-part/EFI ]; then
+	bootoffs=$((32 << K))
+    fi
 }
 
 genboot()
 {
     if [ -d "$bootdata" ]; then
 	bootimg=$(cat <<EOF
-image efi-part.vfat {
+image $BINARIES_DIR/efi-part.vfat {
-	temporary = true
 	size = $bootsize
 	vfat {
 		file EFI {
@@ -85,7 +98,7 @@ EOF
 		offset = $bootoffs
 		partition-type-uuid = U
 		bootable = true
-		image = efi-part.vfat
+		image = $BINARIES_DIR/efi-part.vfat
 	}
 EOF
 		  )
@@ -104,29 +117,44 @@ EOF
     fi
 }
 
-mkdir -p "${WORKDIR}"/root
+common=$(dirname $(readlink -f "$0"))
-rm -rf   "${WORKDIR}"/tmp
+root=$BUILD_DIR/genimage.root
-mkdir -p "${WORKDIR}"/tmp
+tmp=$BUILD_DIR/genimage.tmp
 
-qcowimg="${ARTIFACT}.qcow2"
+total=$((512 << M))
-total=$(size2int $SIZE)
+bootoffs=$((32 << K))
-bootoffs=
+bootdata=
-bootdata=$BOOT_DATA
+diskimg=disk.img
 bootimg=
 bootpart=
+tmpimage=$(mktemp)
+while getopts "a:b:B:n:s:" opt; do
+    case ${opt} in
+	a)
+	    arch=$OPTARG
+	    ;;
+	b)
+	    bootdata=$OPTARG
+	    ;;
+	B)
+	    bootoffs=$(($OPTARG))
+	    ;;
+	n)
+	    diskimg=${OPTARG}
+	    ;;
+	s)
+	    total=$(size2int $OPTARG)
+	    ;;
+    esac
+done
+shift $((OPTIND - 1))
 
-if [ -n "${BOOT_OFFSET}" ]; then
+mkdir -p $root
-    bootoffs=$(($BOOT_OFFSET))
-fi
 
+probeboot
 dimension
 genboot
 
-. $BR2_EXTERNAL_INFIX_PATH/board/common/rootfs/etc/partition-uuid
-[ -n "${AUX_UUID}" ]
-[ -n "${PRIMARY_UUID}" ]
-[ -n "${SECONDARY_UUID}" ]
-
 # Use awk over sed because replacement text may contain newlines,
 # which sed does not approve of.
 awk \
@@ -138,7 +166,7 @@ awk \
 	  -vimgsize=$imgsize \
 	  -vcfgsize=$cfgsize \
 	  -vvarsize=$varsize \
-	  -vqcowimg=$qcowimg \
+	  -vdiskimg=$tmpimage \
 	  -vbootimg="$bootimg" -vbootpart="$bootpart" \
 	  '{
 		sub(/@TOTALSIZE@/, total);
@@ -147,7 +175,7 @@ awk \
 		sub(/@IMGSIZE@/, imgsize);
 		sub(/@CFGSIZE@/, cfgsize);
 		sub(/@VARSIZE@/, varsize);
-		sub(/@QCOWIMG@/, qcowimg);
+		sub(/@DISKIMG@/, diskimg);
 		sub(/@BOOTIMG@/, bootimg);
 		sub(/@BOOTPART@/, bootpart);
 		sub(/@AUXUUID@/, auxuuid);
@@ -155,11 +183,35 @@ awk \
 		sub(/@SECONDARYUUID@/, secondaryuuid);
 
 	  }1' \
-	      < $PKGDIR/genimage.cfg.in >$WORKDIR/genimage.cfg
+	      < $common/genimage.cfg.in >$root/genimage.cfg
+
+mkdir -p $root/aux
+cp -f $BINARIES_DIR/rootfs.itbh $root/aux/primary.itbh
+cp -f $BINARIES_DIR/rootfs.itbh $root/aux/secondary.itbh
+cp -f $BINARIES_DIR/rauc.status $root/aux/rauc.status
+
+case "$arch" in
+    aarch64)
+	mkenvimage -s 0x4000 -o "$root/aux/uboot.env" \
+		   "$BR2_EXTERNAL_INFIX_PATH/board/common/uboot/aux-env.txt"
+	;;
+    x86_64)
+	mkdir -p "$root/aux/grub"
+	cp -f "$BR2_EXTERNAL_INFIX_PATH/board/$arch/grub.cfg" \
+	      "$BR2_EXTERNAL_INFIX_PATH/board/$arch/grubenv"  \
+	      "$root/aux/grub/"
+	;;
+    *)
+	;;
+esac
+
+rm -rf "$tmp"
 
 genimage \
-    --tmppath    "${WORKDIR}"/tmp  \
+    --rootpath "$root" \
-    --rootpath   "${WORKDIR}"/root \
+    --tmppath  "$tmp" \
-    --inputpath  "$BINARIES_DIR"   \
+    --inputpath "$BINARIES_DIR" \
-    --outputpath "$BINARIES_DIR"   \
+    --config "$root/genimage.cfg"
-    --config "${WORKDIR}"/genimage.cfg
+
+qemu-img convert -c -O qcow2 "$tmpimage" "$BINARIES_DIR/$diskimg"
+rm "$tmpimage"

board/common/mkfit.sh

@@ -0,0 +1,118 @@
+#!/bin/sh
+
+die()
+{
+    echo "$@" >&2
+    exit 1
+}
+
+load_cfg()
+{
+    local tmp=$(mktemp -p /tmp)
+
+    grep ^FIT_ $BR2_CONFIG >$tmp
+    .  $tmp
+    rm $tmp
+}
+
+load_cfg
+[ "$FIT_IMAGE" = "y" ] || exit 0
+
+work=$BUILD_DIR/fit-image-local
+dtbs=$(find $BINARIES_DIR -name '*.dtb')
+kernel=$(find $BINARIES_DIR -name '*Image' | head -n1)
+squash=$BINARIES_DIR/rootfs.squashfs
+
+mkdir -p $work
+gzip <$kernel >$work/Image.gz
+kernel=$work/Image.gz
+
+rm -rf $work/rootfs
+unsquashfs -f -d $work/rootfs $squash
+rm -f $work/rootfs/boot/*Image
+
+squash=$work/rootfs-no-kernel.squashfs
+rm -f $squash
+mksquashfs $work/rootfs $squash
+
+# mkimage will only align images to 4 bytes, but U-Boot will leave
+# both DTB and ramdisk in place when starting the kernel. So we pad
+# all components up to a 4k boundary.
+truncate -s %4k $kernel $dtbs
+
+: >$work/dtbs.itsi
+: >$work/cfgs.itsi
+for dtb in $dtbs; do
+    name=$(basename $dtb .dtb)
+
+    cat <<EOF >>$work/dtbs.itsi
+		$name-dtb {
+			description = "$name";
+			type = "flat_dt";
+			arch = "$FIT_ARCH";
+			compression = "none";
+			data = /incbin/("$dtb");
+		};
+EOF
+    cat <<EOF >>$work/cfgs.itsi
+		$name {
+			description = "$name";
+			kernel = "kernel";
+			ramdisk = "ramdisk";
+			fdt = "$name-dtb";
+		};
+EOF
+done
+
+: >$work/kernel-load.itsi
+if [ "$FIT_KERNEL_LOAD_ADDR" ]; then
+    cat <<EOF >$work/kernel-load.itsi
+			load = <$FIT_KERNEL_LOAD_ADDR>;
+			entry = <$FIT_KERNEL_LOAD_ADDR>;
+EOF
+fi
+
+cat <<EOF >$work/infix.its
+/dts-v1/;
+
+/ {
+	timestamp = <$(date +%s)>;
+	description = "Infix ($FIT_ARCH)";
+	creator = "infix";
+	#address-cells = <0x1>;
+
+	images {
+
+		kernel {
+			description = "Linux";
+			type = "kernel";
+			arch = "$FIT_ARCH";
+			os = "linux";
+$(cat $work/kernel-load.itsi)
+			compression = "gzip";
+			data = /incbin/("$kernel");
+		};
+
+		ramdisk {
+			description = "Infix";
+			type = "ramdisk";
+			os = "linux";
+			arch = "$FIT_ARCH";
+			compression = "none";
+			data = /incbin/("$squash");
+		};
+
+$(cat $work/dtbs.itsi)
+
+	};
+
+	configurations {
+$(cat $work/cfgs.itsi)
+	};
+};
+EOF
+
+mkimage \
+    -E -p 0x1000 \
+    -f $work/infix.its $BINARIES_DIR/infix.itb \
+    || die "Unable to create FIT image"

board/common/mkgns3a.sh

@@ -0,0 +1,103 @@
+#!/bin/sh
+# shellcheck disable=SC1091
+. "$TARGET_DIR/etc/os-release"
+
+if [ -n "$INFIX_RELEASE" ]; then
+    rel="-${INFIX_RELEASE}"
+fi
+
+ARCH=$1
+NM="${2:-custom}${rel}"
+DISK=$3
+RAM=${4:-512}
+IFNUM=${5:-1}
+
+# The aarch64 build currently has no "loader" but instead starts Linux
+# directly, so we need to add a basic cmdline.
+loader_args()
+{
+    if [ "$ARCH" = "aarch64" ]; then
+	cat <<EOF
+"kernel_command_line": "console=ttyAMA0 root=PARTLABEL=primary quiet",
+EOF
+    fi
+}
+
+loader_img()
+{
+    if [ "$ARCH" = "x86_64" ]; then
+	cat <<EOF
+"bios_image": "$loader",
+EOF
+    else
+	cat <<EOF
+"kernel_image": "$loader",
+EOF
+    fi
+}
+
+if [ "$ARCH" = "x86_64" ]; then
+    loader=OVMF.fd
+    accel=allow
+    opts=
+else
+    loader=Image
+    accel=disable
+    opts="-M virt -cpu cortex-a72"
+fi
+
+echo ">> Disk image MD5: $(md5sum "$BINARIES_DIR/$DISK" | awk '{print $1}')"
+
+cat <<EOF >"$BINARIES_DIR/${NM}.gns3a"
+{
+    "name": "$NM",
+    "category": "router",
+    "description": "$INFIX_DESC",
+    "vendor_name": "$VENDOR_NAME",
+    "vendor_url": "$VENDOR_HOME",
+    "product_name": "$NAME",
+    "registry_version": 6,
+    "status": "stable",
+    "maintainer": "$VENDOR_NAME",
+    "maintainer_email": "${SUPPORT_URL#mailto:}",
+    "usage": "Default login, user/pass: admin/admin\n\nType 'cli' (and Enter) followed by 'help' for an overview of commands and relevant configuration files.",
+    "port_name_format": "eth{0}",
+    "linked_clone": true,
+    "qemu": {
+        "adapter_type": "virtio-net-pci",
+        "adapters": ${IFNUM},
+        "ram": ${RAM},
+        "cpus": 1,
+        "hda_disk_interface": "virtio",
+        "arch": "$ARCH",
+        "console_type": "telnet",
+        $(loader_img)
+        $(loader_args)
+        "kvm": "$accel",
+	"options": "$opts"
+    },
+    "images": [
+        {
+            "filename": "$loader",
+            "filesize": $(stat --printf='%s' "$BINARIES_DIR/$loader"),
+            "md5sum": "$(md5sum "$BINARIES_DIR/$loader" | awk '{print $1}')",
+            "version": "0.0"
+        },
+        {
+            "filename": "$DISK",
+            "filesize": $(stat --printf='%s' "$BINARIES_DIR/$DISK"),
+            "md5sum": "$(md5sum "$BINARIES_DIR/$DISK" | awk '{print $1}')",
+            "version": "0.0"
+        }
+    ],
+    "versions": [
+        {
+            "name": "0.0",
+            "images": {
+                $(loader_img)
+                "hda_disk_image": "$DISK"
+            }
+        }
+    ]
+}
+EOF

board/common/mkmmc.sh

@@ -0,0 +1,22 @@
+#!/bin/sh
+
+set -e
+
+common=$(dirname $(readlink -f "$0"))
+root=$BUILD_DIR/genimage.root
+tmp=$BUILD_DIR/genimage.tmp
+
+
+mkdir -p $root/aux
+cp -f $BINARIES_DIR/uboot-env.bin $root/aux/uboot.env
+cp -f $BINARIES_DIR/rootfs.itbh $root/aux/primary.itbh
+cp -f $BINARIES_DIR/rootfs.itbh $root/aux/secondary.itbh
+
+rm -rf $tmp
+
+genimage \
+    --rootpath $root \
+    --tmppath  $tmp \
+    --inputpath $BINARIES_DIR \
+    --outputpath $BINARIES_DIR \
+    --config $common/genimage.cfg

board/common/mkrauc-status.sh

@@ -0,0 +1,35 @@
+#!/bin/sh
+
+set -e
+
+# Bootstrap a RAUC status file showing the newly created image
+# installed to both the primary and secondary slots. This then bundled
+# in the aux partition in mkdisk.sh, so that RAUC (on the target) can
+# always report the installed versions.
+rauc info --no-verify --output-format=shell $1 >/tmp/rauc-$$.info
+. /tmp/rauc-$$.info
+rm /tmp/rauc-$$.info
+tstamp=$(date -u +%FT%TZ)
+cat <<EOF
+[slot.rootfs.0]
+bundle.compatible=$RAUC_MF_COMPATIBLE
+bundle.version=$RAUC_MF_VERSION
+status=ok
+sha256=$RAUC_IMAGE_DIGEST_0
+size=$RAUC_IMAGE_SIZE_0
+installed.timestamp=$tstamp
+installed.count=1
+activated.timestamp=$tstamp
+activated.count=1
+
+[slot.rootfs.1]
+bundle.compatible=$RAUC_MF_COMPATIBLE
+bundle.version=$RAUC_MF_VERSION
+status=ok
+sha256=$RAUC_IMAGE_DIGEST_0
+size=$RAUC_IMAGE_SIZE_0
+installed.timestamp=$tstamp
+installed.count=1
+activated.timestamp=$tstamp
+activated.count=1
+EOF

board/common/mkrauc.sh

@@ -0,0 +1,43 @@
+#!/bin/sh
+
+set -e
+
+name=$1
+compat=$2
+sign=$3
+
+crt=$(ls $sign/*.crt)
+key=$(ls $sign/*.key)
+
+common=$(dirname "$(readlink -f "$0")")
+
+work=$BUILD_DIR/mkrauc
+mkdir -p "$work"
+
+cp -f "$common/rauc-hooks.sh" "$work/hooks.sh"
+
+# RAUC internally uses the file extension to find a suitable install
+# handler, hence the name must be .img
+cp -f "$BINARIES_DIR/rootfs.squashfs" "$work/rootfs.img"
+cp -f "$BINARIES_DIR/rootfs.itbh"     "$work/rootfs.itbh"
+
+cat >"$work/manifest.raucm" <<EOF
+[update]
+compatible=${compat}
+version=${INFIX_VERSION}
+
+[bundle]
+format=verity
+
+[hooks]
+filename=hooks.sh
+
+[image.rootfs]
+filename=rootfs.img
+hooks=post-install
+EOF
+
+rm -f "$BINARIES_DIR/$name.pkg"
+
+rauc --cert="$crt" --key="$key" \
+     bundle "$work" "$BINARIES_DIR/$name.pkg"

board/common/post-image.sh

@@ -0,0 +1,112 @@
+#!/bin/sh
+# shellcheck disable=SC2086
+
+common=$(dirname "$(readlink -f "$0")")
+. "$common/lib.sh"
+
+# shellcheck disable=SC1091
+. "$TARGET_DIR/etc/os-release"
+
+# The INFIX_* variables may be composed from BR2_* variables,
+# so we source them last.
+load_cfg BR2_ARCH
+load_cfg BR2_DEFCONFIG
+load_cfg BR2_EXTERNAL_INFIX_PATH
+load_cfg BR2_TARGET_ROOTFS
+load_cfg INFIX_ID
+load_cfg INFIX_COMPATIBLE
+
+# The default IMAGE_ID is infix-$BR2_ARCH but can be overridden
+# for imaage names, and compat strings, like infix-r2s
+if [ -n "$IMAGE_ID" ]; then
+    NAME="$IMAGE_ID"
+else
+    NAME="$INFIX_ID"-$(echo "$BR2_ARCH" | tr _ - | sed 's/x86-64/x86_64/')
+fi
+diskimg=disk.qcow2
+
+ver()
+{
+    if [ -n "$INFIX_RELEASE" ]; then
+	printf -- "-%s" "${INFIX_RELEASE#v}"
+	return
+    fi
+}
+
+load_cfg SIGN_ENABLED
+if [ "$SIGN_ENABLED" = "y" ]; then
+    load_cfg BR2_ARCH
+    load_cfg SIGN_KEY
+
+    ixmsg "Signing SquashFS Image"
+    $common/sign.sh $BR2_ARCH $SIGN_KEY
+
+    ixmsg "Creating RAUC Update Bundle"
+    $common/mkrauc.sh "$NAME$(ver)" $INFIX_COMPATIBLE $SIGN_KEY
+fi
+
+load_cfg DISK_IMAGE
+if [ "$DISK_IMAGE" = "y" ]; then
+    ixmsg "Creating Disk Image"
+    diskimg="${NAME}-disk$(ver).qcow2"
+    bootcfg=
+    if [ "$DISK_IMAGE_BOOT_DATA" ]; then
+	bootcfg="-b $DISK_IMAGE_BOOT_DATA -B $DISK_IMAGE_BOOT_OFFSET"
+    fi
+
+    if [ "$BR2_TARGET_ROOTFS_SQUASHFS" != "y" ] && \
+       [ ! -f "$BINARIES_DIR/rootfs.squashfs" ]; then
+	ixmsg "  Injecting $DISK_IMAGE_RELEASE_URL"
+	archive="$BINARIES_DIR/$(basename $DISK_IMAGE_RELEASE_URL)"
+	[ -f "$archive" ] || wget -O"$archive" "$DISK_IMAGE_RELEASE_URL"
+	tar -xa --strip-components=1 -C "$BINARIES_DIR" -f "$archive"
+    fi
+
+    $common/mkrauc-status.sh "$BINARIES_DIR/${NAME}.pkg" >"$BINARIES_DIR/rauc.status"
+    $common/mkdisk.sh -a $BR2_ARCH -n $diskimg -s $DISK_IMAGE_SIZE $bootcfg
+fi
+
+load_cfg SDCARD_AUX
+if [ "$SDCARD_AUX" = "y" ]; then
+    ixmsg "Creating initial rauc.status"
+    $common/mkrauc-status.sh "$BINARIES_DIR/${NAME}.pkg" >"$BINARIES_DIR/rauc.status"
+    ixmsg "Creating aux.ext4 for sdcard.img"
+    $common/mkaux.sh
+fi
+
+load_cfg GNS3_APPLIANCE
+if [ "$GNS3_APPLIANCE" = "y" ]; then
+    ixmsg "Creating GNS3 Appliance, $GNS3_APPLIANCE_RAM MiB with $GNS3_APPLIANCE_IFNUM ports"
+    $common/mkgns3a.sh $BR2_ARCH $NAME $diskimg $GNS3_APPLIANCE_RAM $GNS3_APPLIANCE_IFNUM
+fi
+
+load_cfg FIT_IMAGE
+if [ "$FIT_IMAGE" = "y" ]; then
+    ixmsg "Creating Traditional FIT Image"
+    $common/mkfit.sh
+fi
+
+# Only for regular builds, not bootloader-only builds
+if [ "$BR2_TARGET_ROOTFS_SQUASHFS" = "y" ]; then
+    rel=$(ver)
+    ln -sf rootfs.squashfs "$BINARIES_DIR/${NAME}${rel}.img"
+    if [ -n "$rel" ]; then
+	ln -sf "${NAME}${rel}.img" "$BINARIES_DIR/${NAME}.img"
+    fi
+
+    cp "$BR2_EXTERNAL_INFIX_PATH/board/common/rootfs/usr/bin/onieprom" "$BINARIES_DIR/"
+
+    # Menuconfig support for modifying Qemu args in release tarballs
+    cp "$BR2_EXTERNAL_INFIX_PATH/board/common/qemu/qemu.sh" "$BINARIES_DIR/"
+    sed -e "s/@ARCH@/QEMU_$BR2_ARCH/" \
+	-e "s/@DISK_IMG@/$diskimg/"   \
+	< "$BR2_EXTERNAL_INFIX_PATH/board/common/qemu/Config.in.in" \
+	> "$BINARIES_DIR/Config.in"
+    rm -f "$BINARIES_DIR/qemu.cfg"
+    CONFIG_="CONFIG_" BR2_CONFIG="$BINARIES_DIR/qemu.cfg" \
+	   "$O/build/buildroot-config/conf" --olddefconfig "$BINARIES_DIR/Config.in"
+    rm -f "$BINARIES_DIR/qemu.cfg.old" "$BINARIES_DIR/.config.old"
+
+    # Quick intro for beginners, with links to more information
+    cp "$BR2_EXTERNAL_INFIX_PATH/board/common/README.txt" "$BINARIES_DIR/"
+fi

board/common/qemu/Config.in.in

@@ -1,11 +1,5 @@
 mainmenu "QEMU Virtualization"
 
-config QEMU_ARCH_IS_32
-	bool
-
-config QEMU_ARCH_IS_64
-	bool
-
 choice
 	prompt "Target Architecture"
 	default @ARCH@
@@ -18,10 +12,6 @@ config QEMU_x86_64
 	bool "x86_64"
 	select QEMU_ARCH_IS_64
 
-config QEMU_arm
-	bool "AArch32 (little endian)"
-	select QEMU_ARCH_IS_32
-
 config QEMU_aarch64
 	bool "AArch64 (little endian)"
 	select QEMU_ARCH_IS_64
@@ -64,7 +54,6 @@ endchoice
 
 choice
      prompt "Console"
-     default QEMU_CONSOLE_SERIAL if QEMU_arm
      default QEMU_CONSOLE_VIRTIO
 
 config QEMU_CONSOLE_VIRTIO
@@ -77,16 +66,15 @@ endchoice
 
 config QEMU_MACHINE
 	string "Select emulated machine"
-	default "qemu-system-arm     -M virt,accel=kvm:tcg -cpu max" if QEMU_arm
+	default "qemu-system-aarch64 -M virt,accel=kvm:tcg -cpu max,pauth-impdef=on" if QEMU_aarch64
-	default "qemu-system-aarch64 -M virt,accel=kvm:tcg -cpu cortex-a53" if QEMU_aarch64
 	default "qemu-system-x86_64  -M pc,accel=kvm:tcg   -cpu max" if QEMU_x86_64
 	help
 	  You should not have to change this setting, although you may
 	  want to tweak it, or change the acceleration.
 
 	  The default is based on the Buildroot architecture, selected by
-	  the defconfig you started with.  Currently Infix supports
+	  the defconfig you started with.  Currently Infix supports only
-	  arm (AArch32), aarch64 (ARM64), and x86_64 (AMD64).
+	  aarch64 (ARM64) and x86_64 (AMD64).
 
 config QEMU_MACHINE_RAM
 	string "RAM size (k/M/G)"
@@ -99,20 +87,19 @@ config QEMU_MACHINE_RAM
 config QEMU_KERNEL
 	string
 	depends on QEMU_LOADER_KERNEL
-	default "../zImage"  if QEMU_arm
+	default "Image"   if QEMU_aarch64
-	default "../Image"   if QEMU_aarch64
+	default "bzImage" if QEMU_x86_64
-	default "../bzImage" if QEMU_x86_64
 
 config QEMU_BIOS
 	string
 	depends on !QEMU_LOADER_KERNEL
-	default "../u-boot.bin" if QEMU_LOADER_UBOOT
+	default "u-boot.bin" if QEMU_LOADER_UBOOT
-	default "../OVMF.fd"    if QEMU_LOADER_OVMF
+	default "OVMF.fd"    if QEMU_LOADER_OVMF
 
 config QEMU_ROOTFS
 	string
 	default "@DISK_IMG@" if !QEMU_ROOTFS_INITRD
-	default "../rootfs.squashfs" if QEMU_ROOTFS_INITRD
+	default "rootfs.squashfs" if QEMU_ROOTFS_INITRD
 
 config QEMU_DTB_EXTEND
 	bool
@@ -224,15 +211,12 @@ endchoice
 
 config QEMU_NET_MODEL
 	string "Interface model"
-	default "virtio-net-device" if QEMU_arm
 	default "virtio-net-pci"
 	help
 	  The default, virtio-net-pci, NIC works for most use-cases, but
 	  if you want to play with low-level stuff like ethtool, you
 	  might want to test the Intel 82545EM driver, e1000.
 
-	  Note: ARM32 uses virtio-net-device (MMIO) by default.
-
 config QEMU_NET_BRIDGE_DEV
 	string "Bridge device"
 	depends on QEMU_NET_BRIDGE

board/common/qemu/qemu.mk

@@ -1,45 +0,0 @@
-################################################################################
-#
-# qemu-scripts
-#
-################################################################################
-
-QEMU_SCRIPTS_DIR := $(pkgdir)
-qemu-kconfig = \
-	CONFIG_="CONFIG_" \
-	BR2_CONFIG="$(BINARIES_DIR)/qemu/.config" \
-	$(BUILD_DIR)/buildroot-config/$(1) $(2) "$(BINARIES_DIR)/qemu/Config.in"
-
-ifeq ($(QEMU_SCRIPTS),y)
-
-.PHONY: run
-run:
-	@$(BINARIES_DIR)/qemu/run.sh
-
-.PHONY: run-menuconfig
-run-menuconfig: $(BUILD_DIR)/buildroot-config/mconf
-	@$(call qemu-kconfig,mconf)
-
-qemu-scripts: \
-		$(BINARIES_DIR)/qemu/run.sh \
-		$(BINARIES_DIR)/qemu/Config.in \
-		$(BINARIES_DIR)/qemu/.config
-
-$(BINARIES_DIR)/qemu/run.sh: $(QEMU_SCRIPTS_DIR)/run.sh
-	@$(call IXMSG,"Installing QEMU scripts")
-	@mkdir -p $(dir $@)
-	@cp $< $@
-
-$(BINARIES_DIR)/qemu/Config.in: $(QEMU_SCRIPTS_DIR)/Config.in.in
-	@mkdir -p $(dir $@)
-	@sed \
-		-e "s:@ARCH@:QEMU_$(BR2_ARCH):" \
-		-e "s:@DISK_IMG@:../$(INFIX_ARTIFACT).qcow2:" \
-	< $< >$@
-
-$(BINARIES_DIR)/qemu/.config: $(BINARIES_DIR)/qemu/Config.in
-	@$(call qemu-kconfig,conf,--olddefconfig)
-	@rm -f $@.old
-
-TARGETS_ROOTFS += qemu-scripts
-endif

board/common/qemu/qemu.sh

@@ -19,8 +19,8 @@
 #
 # shellcheck disable=SC3037
 
-qdir=$(dirname "$(readlink -f "$0")")
+# Local variables
-imgdir=$(readlink -f "${qdir}/..")
+imgdir=$(readlink -f "$(dirname "$0")")
 prognm=$(basename "$0")
 
 usage()
@@ -56,8 +56,12 @@ die()
 
 load_qemucfg()
 {
+    tmp=$(mktemp -p /tmp)
+
+    grep ^CONFIG_QEMU_ "$1" >"$tmp"
     # shellcheck disable=SC1090
-    .  "./.config"
+    .  "$tmp"
+    rm "$tmp"
 
     [ "$CONFIG_QEMU_MACHINE" ] || die "Missing QEMU_MACHINE"
     [ "$CONFIG_QEMU_ROOTFS"  ] || die "Missing QEMU_ROOTFS"
@@ -80,10 +84,7 @@ loader_args()
 
 append_args()
 {
-    # ARM32 doesn't support virtio console properly, always use serial
+    if [ "$CONFIG_QEMU_CONSOLE_VIRTIO" ]; then
-    if [ "$CONFIG_QEMU_arm" ]; then
-	echo -n "console=ttyAMA0 "
-    elif [ "$CONFIG_QEMU_CONSOLE_VIRTIO" ]; then
 	echo -n "console=hvc0 "
     elif [ "$CONFIG_QEMU_x86_64" ]; then
 	echo -n "console=ttyS0 "
@@ -119,13 +120,7 @@ rootfs_args()
 	echo -n "-device sd-card,drive=mmc "
 	echo -n "-drive id=mmc,file=$CONFIG_QEMU_ROOTFS,if=none,format=raw "
     elif [ "$CONFIG_QEMU_ROOTFS_VSCSI" = "y" ]; then
-	# ARM32 virt machine uses MMIO virtio devices, not PCI
+	echo -n "-drive file=qemu.qcow2,if=virtio,format=qcow2,bus=0,unit=0 "
-	if [ "$CONFIG_QEMU_arm" ]; then
-	    echo -n "-drive file=qemu.qcow2,if=none,format=qcow2,id=rootfs "
-	    echo -n "-device virtio-blk-device,drive=rootfs "
-	else
-	    echo -n "-drive file=qemu.qcow2,if=virtio,format=qcow2,bus=0,unit=0 "
-	fi
     fi
 }
 
@@ -178,38 +173,22 @@ rw_args()
 	dd if=/dev/zero of="aux.ext4" bs=1M count=1 >/dev/null 2>&1
 	mkfs.ext4 -L aux "aux.ext4" >/dev/null 2>&1
     fi
+    echo -n "-drive file=aux.ext4,if=virtio,format=raw,bus=0,unit=3 "
 
     if ! [ -f "$CONFIG_QEMU_RW" ]; then
 	dd if=/dev/zero of="$CONFIG_QEMU_RW" bs=16M count=1 >/dev/null 2>&1
 	mkfs.ext4 -L cfg "$CONFIG_QEMU_RW" >/dev/null 2>&1
     fi
 
-    # ARM32 virt machine uses MMIO virtio devices, not PCI
+    echo -n "-drive file=$CONFIG_QEMU_RW,if=virtio,format=raw,bus=0,unit=1 "
-    if [ "$CONFIG_QEMU_arm" ]; then
-	echo -n "-drive file=aux.ext4,if=none,format=raw,id=aux "
-	echo -n "-device virtio-blk-device,drive=aux "
-	echo -n "-drive file=$CONFIG_QEMU_RW,if=none,format=raw,id=cfg "
-	echo -n "-device virtio-blk-device,drive=cfg "
 
-	if [ "$CONFIG_QEMU_RW_VAR_OPT" ]; then
+    if [ "$CONFIG_QEMU_RW_VAR_OPT" ]; then
-	    if ! [ -f "$CONFIG_QEMU_RW_VAR" ]; then
+	if ! [ -f "$CONFIG_QEMU_RW_VAR" ]; then
-		dd if=/dev/zero of="$CONFIG_QEMU_RW_VAR" bs=$CONFIG_QEMU_RW_VAR_SIZE count=1 >/dev/null 2>&1
+	    dd if=/dev/zero of="$CONFIG_QEMU_RW_VAR" bs=$CONFIG_QEMU_RW_VAR_SIZE count=1 >/dev/null 2>&1
-		mkfs.ext4 -L var "$CONFIG_QEMU_RW_VAR" >/dev/null 2>&1
+	    mkfs.ext4 -L var "$CONFIG_QEMU_RW_VAR" >/dev/null 2>&1
-	    fi
-	    echo -n "-drive file=$CONFIG_QEMU_RW_VAR,if=none,format=raw,id=var "
-	    echo -n "-device virtio-blk-device,drive=var "
 	fi
-    else
-	echo -n "-drive file=aux.ext4,if=virtio,format=raw,bus=0,unit=3 "
-	echo -n "-drive file=$CONFIG_QEMU_RW,if=virtio,format=raw,bus=0,unit=1 "
 
-	if [ "$CONFIG_QEMU_RW_VAR_OPT" ]; then
+	echo -n "-drive file=$CONFIG_QEMU_RW_VAR,if=virtio,format=raw,bus=0,unit=2 "
-	    if ! [ -f "$CONFIG_QEMU_RW_VAR" ]; then
-		dd if=/dev/zero of="$CONFIG_QEMU_RW_VAR" bs=$CONFIG_QEMU_RW_VAR_SIZE count=1 >/dev/null 2>&1
-		mkfs.ext4 -L var "$CONFIG_QEMU_RW_VAR" >/dev/null 2>&1
-	    fi
-	    echo -n "-drive file=$CONFIG_QEMU_RW_VAR,if=virtio,format=raw,bus=0,unit=2 "
-	fi
     fi
 }
 
@@ -243,7 +222,7 @@ rocker_port_args()
 net_args()
 {
     # Infix will pick up this file via fwcfg and install it to /etc
-    mactab=${qdir}/mactab
+    mactab=${imgdir}/mactab
     :> "$mactab"
     echo -n "-fw_cfg name=opt/mactab,file=$mactab "
 
@@ -282,7 +261,7 @@ vpd_args()
 {
     [ "$CONFIG_QEMU_VPD" = "y" ] || return
 
-    vpd_file="${qdir}/vpd"
+    vpd_file="${imgdir}/vpd"
 
     if ! [ -f "$vpd_file" ]; then
 	onieprom="${imgdir}/onieprom"
@@ -334,35 +313,8 @@ gdb_args()
     echo -n "-gdb chardev:gdbqemu"
 }
 
-extract_squashfs()
-{
-    # Extract rootfs.squashfs from rootfs.itb if missing
-    # The .itb file is rootfs.itbh (4096 bytes) + rootfs.squashfs
-    input="${1:-rootfs.itb}"
-    output="${2:-rootfs.squashfs}"
-
-    [ -f "$input" ] || die "Cannot extract $output: $input not found"
-
-    echo "Extracting $output from $input (skipping 4096-byte FIT header)..."
-    dd if="$input" of="$output" bs=4096 skip=1 2>/dev/null \
-        || die "Failed to extract $output from $input"
-
-    echo "Successfully created $output"
-}
-
 run_qemu()
 {
-    # Auto-extract rootfs.squashfs from rootfs.itb if needed for initrd mode
-    if [ "$CONFIG_QEMU_ROOTFS_INITRD" = "y" ]; then
-	if [ "$CONFIG_QEMU_ROOTFS" = "rootfs.squashfs" ] && [ ! -f "rootfs.squashfs" ]; then
-	    if [ -f "rootfs.itb" ]; then
-		extract_squashfs "rootfs.itb" "rootfs.squashfs"
-	    else
-		die "Missing rootfs.squashfs and cannot find rootfs.itb to extract it from"
-	    fi
-	fi
-    fi
-
     if [ "$CONFIG_QEMU_ROOTFS_VSCSI" = "y" ]; then
 	if ! qemu-img check "qemu.qcow2"; then
 	    rm -f "qemu.qcow2"
@@ -426,7 +378,7 @@ dtb_args()
 
 	# Extend it with the environment and signing information in
 	# u-boot.dtb.
-	echo "qemu.dtb ../u-boot.dtb" | \
+	echo "qemu.dtb u-boot.dtb" | \
 	    xargs -n 1 dtc -I dtb -O dts | \
 	    { echo "/dts-v1/;"; sed  -e 's:/dts-v[0-9]\+/;::'; } | \
 	    dtc >qemu-extended.dtb 2>/dev/null
@@ -435,7 +387,7 @@ dtb_args()
 	echo -n "-dtb qemu-extended.dtb "
     else
 	# Otherwise we just use the unmodified one
-	echo -n "-dtb ../u-boot.dtb "
+	echo -n "-dtb u-boot.dtb "
     fi
 }
 
@@ -481,12 +433,13 @@ EOF
 
 menuconfig()
 {
-    grep -q QEMU_MACHINE Config.in || die "$prognm: must be run from the $$O/images/qemu directory"
+    grep -q QEMU_MACHINE Config.in || die "$prognm: must be run from the output/images directory"
     command -v kconfig-mconf >/dev/null || die "$prognm: cannot find kconfig-mconf for menuconfig"
     exec kconfig-mconf Config.in
 }
 
-cd "$qdir" || (echo "Failed cd to $qdir"; exit 1)
+scriptdir=$(dirname "$(readlink -f "$0")")
+cd "$scriptdir" || (echo "Failed cd to $scriptdir"; exit 1)
 
 while [ "$1" != "" ]; do
     case $1 in
@@ -505,7 +458,13 @@ while [ "$1" != "" ]; do
     shift
 done
 
-load_qemucfg
+if [ -f .config ]; then
+    # Customized settings from 'qemu.sh -c'
+    load_qemucfg .config
+else
+    # Shipped defaults from release tarball
+    load_qemucfg qemu.cfg
+fi
 
 if [ -z "$QEMU_EXTRA_APPEND" ]; then
     QEMU_EXTRA_APPEND="$*"

board/common/rootfs.its

@@ -0,0 +1,28 @@
+/dts-v1/;
+
+/ {
+	description = "Infix";
+	creator = "infix";
+	#address-cells = <0x1>;
+
+	images {
+		rootfs {
+			description = "Infix";
+			type = "ramdisk";
+			os = "linux";
+			compression = "none";
+			data = /incbin/("rootfs.squashfs");
+			signature-1 {
+				algo = "sha256,rsa4096";
+				key-name-hint = "infix";
+			};
+		};
+	};
+
+	configurations {
+		default = "verity";
+		verity {
+			ramdisk = "rootfs";
+		};
+	};
+};

board/common/rootfs/etc/bash.bashrc

@@ -31,8 +31,6 @@ bind "set completion-ignore-case on"
 # show all completions immediately instead of ringing bell
 bind "set show-all-if-ambiguous on"
 
-export LANG=C.UTF-8
-
 log()
 {
     local fn="/var/log/syslog"

board/common/rootfs/etc/finit.conf

@@ -1,3 +1,2 @@
 set COLORTERM=yes
-set LANG=C.UTF-8
+rlimit soft core infinity
-rlimit soft core infinity

board/common/rootfs/etc/fstab

@@ -16,7 +16,7 @@ cfgfs		/config		configfs	nofail,noauto		0	0
 # /home, /root, and /var, are determined dynamically by /usr/libexec/infix/mnt
 # depending on the available devices.
 mnttmp		/mnt/tmp	tmpfs	defaults					0	0
-LABEL=aux	/mnt/aux	auto	noatime,nodiratime,noauto,errors=remount-ro	0	0
+LABEL=aux	/mnt/aux	ext2	noatime,nodiratime,noauto,errors=remount-ro	0	0
 LABEL=var	/mnt/var	ext4	noatime,nodiratime,noauto,commit=30,errors=remount-ro	0 0
 LABEL=cfg	/mnt/cfg	ext4	noatime,nodiratime,noauto,commit=30,errors=remount-ro	0 0
 hostfs		/mnt/host	9p	cache=none,msize=16384,noauto			0	0