Either indent by four spaces or use backticks. Depending on the output
generator they may apply different styling though.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Enabled by user enabling IPv6 forwarding on any interface. This change
also enables net.ipv6.conf.all.accept_ra (=2) to accept any IPv6 route
advertisements even when acting as a router.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This patch drops a needless restriction of IP addresses on VLAN filtering
bridges from 2024-03-06. The obvious use-case is when the bridge is an
untagged member of a VLAN and only ony management VLAN is required.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- Introduce the term MAC bridge in the networking documentation
- List the limitation to one MAC bridge on Marvell Linkstree
- Adding lego pictures for the MAC bridge and VLAN bridge examples
[skip ci]
This patch mainly updates the static routing chapter, and adds a new
section on route preferences, but it also makes slight touch-ups at
a few other places as well.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This patch allows a user to specify a specific 169.254/16 address that
the zeroconf client starts with when probing for a free address. If the
probe fails it falls back to its default algorithm.
Fixes#628
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- Drop doc/README.md symlink to variant.md
- Make doc/README.md the table of contents
- Clean up variant.md, OSPF and containers now fully supported
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Updating VLAN interface doc inline with current implementation
Mathias has fixed the syntactic sugar when creating eth0.20 interfaces, thus the associated documentation example is updated accordingly.
A very limited part of the YANG model is implemented so far, basicly it is OSPFv2 with multiple areas and you can change timers
for the interfaces. Limited operational support.
admin@infix-00-00-00:/config/> edit routing control-plane-protocol ietf-ospf:ospfv2 name default
admin@infix-00-00-00:/config/routing/control-plane-protocol/ietf-ospf:ospfv2/name/default/> set ospf area 0.0.0.0 interface e0 enabled true
admin@infix-00-00-00:/config/routing/control-plane-protocol/ietf-ospf:ospfv2/name/default/> leave
In review discussions we have decided, for resonsons of consistency over
correctness, to rename this column to match the YANG model node name
rather than the Linux kernel name.
Also, right align the values. Numbers should always be right-aligned.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
With the latest bump of klish-plugin-sysrepo we no longer need the extra
container name in commands and paths.
Also, update the "show interfaces" example in the top-level README.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Adding missing information
- that PVID should (typically) be set for ports associated untagged
- that the bridge should associated with VLAN to terminate the VLAN
in the bridge
Providing an additional config example (VLAN atop brigde)
Adding picture for this and the existing example (VLAN atop Eth)
Adding info on name conventions (eth.20 vs vlan10)
[skip ci]
Fixes to IPv6 address origin (type 'random' rather than 'other')
now reflected in documentation.
Also using 'admin' instead of 'root' user in examples.
Improved "show interfaces" information is now
reflected in IP address examples
- source info added
- IPv6 addresses shown
Also added an example with IPv6 privacy for stateless autoconfig
Joachim Wiberg