Apparently the BCM2835 watchdog driver does not hook into /dev/watchdog
but creates its own /dev/watchdog0, and is very picky about interval and
timeout as well it seems.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- switch to 6.12 LTS, same as other Infix boards
- trim down kernel config a bit
- sync defconfig with r2s to switch to Finit
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- Bump kernel to 6.12.21, same as other tier one boards
- Fix#1006 byt enabling netlink for ethtool (now works!)
- Sync defconfigs:
- LIBXCRYPT now in an rdep of another package
- Disable FORCE check hashes for now
- Drop patches for 6.10 tree (r2s kernel)
- Port RTL8153b patch for R2S LAN LED support
Fixes#1006
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- Updating SSH information
- Adding Web services information (general, RESTCONF and Web Console)
- Adding Console information
Generic info, and some updates w.r.t specific boards (baudrate, etc)
Introduce a new approach to dtb-building:
Old way: `rsync` an overlay containing our dt source to the kernel,
and then build via buildroot's `_INTREE_DTS_NAME`. This does not work
in recent kernels (at least since 6.12), which requires all dtb's to
be explicitly listed in a `Makefile`.
New way: Create a separate package for every board, and build the
device trees via the kernel's standard interface for building external
modules. This has two main advantages:
1. We can easily interpose a patched version of an upstream device
tree. E.g., we can easily set the factory password.
2. It is much easier to get an overview of which boards are enabled,
rather than scrolling back and forth in the `_INTREE_DTS_NAME` list.
Enable all fully supported boards in the defconfigs.
After the initial probe, set up all port leds:
- Disable all LEDs
- Enable netdev trigger for all green LEDs (tp + sfp)
- Enable link statux and rx/tx activity
- Skip all aux LEDs
Also in script, a neat little flash function that can be used both for a
production test, to verify all LEDs work, and at runtime to locate the
device in a rack of devicess.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
On Rev. B, the second LED on the copper ports is green instead of yellow.
This patch renames them from yellow -> aux => <device>:aux:tp
Also on Rev. B, the second LED for SFP ports do not work at all. This
patch drops them from the device tree to avoid confusion.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The RTC in the CN913x series does not have any "valid" bit, and this
board (all revs) does not have any backup power connected, so it will
return garbage values after every vold boot.
It was therefore decided to disable the RTC completely and set system
time manually, or using an NTP client. This way any time skips would
only ever be forward, never backwards.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- add default-deny-all rule from 2341e07
- enable iburst for the ntp client (quicker initial sync)
- bump meta version (to skip .cfg migration at boot)
Fix#750 [skip ci]
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
In order for the probe logic to source product data from a VPD, it
must be marked as such. Otherwise we end up in a scenario where the
data is collected, but not hoisted up to the system level, leaving the
system without a defined base-MAC for instance.
When the interface is up and has a 'proto dhcp' address the WAN LED is
lit up. When the interface goes down, or loses its DHCP lease, the LED
is turned off.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Allow reset button on the R2S to be used for factory reset at power-on.
See board README for details.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This patch further cleans up the r2s kernel config and also enables the
input event framework for the gpio0 reset button on the device.
The very simple input-event-daemon is introduced, with the only purpose
of listening to /dev/input/event1 for KEY_RESTART and trigger reboot.
Some helpful tooling is also added to help debug events (evtest).
Issue #276
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This serves as an example of how a board specific builds in Infix can
carry a static factory-config. This will be extended upon as we add
support for DHCP server, WiFi access point, and firewall support.
For now the following features are added:
- Default hostname: r2s instead of infix-00-00-00
- LAN port always at 192.168.2.1/24, IPv6 SLAAC enabled
- WAN port has DHCP enabled for IPv4, IPv6 SLAAC disabled
- NTP client enabled, default server pool.ntp.org
- DHCP client is set up to request and allow ntp server
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The R2S has a minimal set of system LEDs, all of which are single color.
This commit tries to distill and map the essence of the Infix functions
to available LEDs.
The SYS LED is turned on (fainy red) at power-on, when U-Boot has loaded
the kernel it turns the SYS LED bright red on. The idea is then to turn
the red SYS LED off as soon as the system has successfully loaded system
startup-config, and then turn the green LAN LED on. Indicating that the
both the device is operational and that the user can connect to the LAN
port.
The WAN LED is given a "wan-up" input condition, with the intention of
turning it on (green) when the device has acquired a DHCP address.
The failure modes, which in many ways is the essence of Infix signaling,
are fail-safe and panic, triggered by loading failure-config, or failing
to loadd failure-config, respectively. In fail-safe mode the SYS LED is
blinking red at 5 Hz and in panic mode *all* LEDs blink at 5 Hz.
Issue #276
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
With new features & fixes, Infix grows. With the latest support for
rauc upgrades introduced with the VisionFive2, and now also for R2S,
we need to reserve room for future upgrades even when running from
an SD card.
This is a quick fix for genimge generated SD card imaages before we
get a proper installer in place that can be used both on the target
and host systems to partition and provision an eMMC, NVME, SSD, or
an SD card.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This change allows modifying and saving the U-Boot environment to the
aux partition on the NanoPi R2S. Required to able to safely maintain
multiple R2S devices on the same LAN.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- Bump kernel to 6.10.3
- Initial defconfig sync with aarch64
- Enable kprobes, ksyms, and function tracer
- Enable missing file systems for parity with Infix
- Enable bridging, netfilter, and other Infix requirements
- Initial virtion support for running in Qemu (untested)
- Enable device mapper, required for rauc bundle install
- Make dummy and tunnel drivers modules to be able to drop dummy0
and tunl0 interfaces that otherwise mess up "show interfaces"
- Disable suspend and hibernation, not supported in Infix
- Disable unused GPIO, PHY, MDIO, and USB drivers
- Disable RK3328 watchdog driver, cannot perform reset on R2S,
enablle softdog instead as a seamless replacement for Infix.
Even though not optimal (since it's software) reboot works
- Disable ethtool netlink support, does not work and breaks
interface configuration completely on R2S!
- Enable netdev LED triggers, for LAN and WAN LEDs
- Bump u-boot to 2024.07
- Hard code developer mode to allow shell access
- Disable factory reset button support (not yet supported)
- Bump ATF to v2.9
- Enable squashfs for rootfs image
- Enable signing of images
- Add secondary partition
- Add dedicated var partition
- Add aux partition for signatures and uboot env
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
For consistency with the / + /usr merge, see 2194f7be, let's move the
last remnants in /: /libexec/infix to /usr/libexec/infix
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
From https://en.wikipedia.org/wiki/exFAT:
... a file system optimized for flash memory such as USB flash
drives and SD cards.
... has been adopted by the SD Association as the default file
system for SDXC and SDUC cards larger than 32 GB.
The exfatprogs is also a default installed package on most modern
distros, compared to dosfstools (mkfs.vfat) which is not.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
We no longer need to set bootdelay on development platforms. You can
now always get to the bootmenu with a Ctrl-C, from there you can get
to the shell if developer mode is enabled. Therefore, override the
default dev-mode detection to statically enable it on the CRB.
Since we don't have any VPD defined on this board, supply a default
password hash via the device tree instead.
Also, specify the path to external USB port, so that Infix will pick
it up in ietf-hardware.
Provide a patched device tree that:
- Uses the correct phy-mode for eth2, allowing it to be probed
properly
- Wires up the interrupt signal to the GPIO expander, so that the SFP
cage's I/O lines can be configured as interrupts, rather than having
to poll them
This is not a production target, so we choose the more developer
friendly option of allowing the boot process to be interrupted.
Also, remove the old update cruft and rely on Marvell's `bubt`
instead.
The BootROM wants the bootloader to be located on LBA1, which is not
ideal when using a GPT to describe the partition table.
Make sure the `bubt` command targets SPI by default.
In order to make use of the DCB support in mv88e6xxx we also enable it
in the kernel config.
Fixes: 3a73ce3cfb ("kernel: Import EtherType based priority override support")
Only port 2 has an SGMII compatible SERDES. When referencing the
SERDES (comphy), the second argument must contain the port number in
order for the comphy driver to pick the correct configuration.
