This patch drops a needless restriction of IP addresses on VLAN filtering
bridges from 2024-03-06. The obvious use-case is when the bridge is an
untagged member of a VLAN and only ony management VLAN is required.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
With the FRR upgrade to 9.1.2, OSPF sometimes reports neighbors
without reporting the routerDesignatedId and routerDesignatedBackupId
attributes. Ensure that these attributes are available before trying
to copy them to the output.
During development of the upcoming ospf_container test, an issue was
discovered where zebra's view of the system drifted from the kernel's
ditto. Specifically: when transitioning from test-config to one with
many virtual interfaces (VLANs VETH pairs etc.), zebra would not
process events for all interfaces, which meant OSPF would not pick
them up.
Our experience matches very well with a bug reported upstream in:
https://github.com/FRRouting/frr/issues/13630
> If we delete kernel interface and create it and set its ip in a
> short time, in rare cases, interface ip will be lost in zebra which
> can be confirmed by vtysh show interface brirf command. This will
> lead to abnormal behavior of other protocol daemons, for example,
> bgpd does not announce the route corresponding to interface ip even
> it was specified by network command.
The issue was marked as fixed by PR 13396, which was merged in the 9.0
cycle:
https://github.com/FRRouting/frr/pull/13396
Therefore, upgrade FRR to the latest patch release from that major.
During debugging of a reconfiguration issue, one hypothesis was that
the tracking of callbacks used to determine when a transaction has
completed (as sysrepo has no hooks for this) was out of sync, causing
us to call `initctl reload` prematurely. This was not the case, but if
it ever occurs in the future, make sure that it is a fatal error that
won't go unnoticed.
- Verify that broadcast packets are also properly moved accross the
bridge, i.e. the broadcast packets sent from vlan interface VLAN10
do not reach VLAN20
Fixes#773
Fix lack of syslog messages from Zebra and add support to easily enable
debug logs for common Zebra subsystems.
Same change made to ospfd for symmetry.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This fixes a regression in v24.11.0, introduced in 46dd0c7, where line
drawing characters are not properly displayed in the CLI anymore.
admin@infix:/> show interfaces
INTERFACE PROTOCOL STATE DATA
lo ethernet UP 00:00:00:00:00:00
ipv4 127.0.0.1/8 (static)
ipv6 ::1/128 (static)
br0 bridge
<E2><94><82> ethernet UP 02:00:00:00:00:00
<E2><94><82> ipv4 169.254.1.3/16 (random)
<E2><94><82> ipv6 fe80::ff:fe00:0/64 (link-layer)
<E2><94><9C> swp1 bridge FORWARDING
<E2><94><9C> swp2 bridge FORWARDING
<E2><94><9C> swp3 bridge FORWARDING
<E2><94><9C> swp4 bridge FORWARDING
<E2><94><9C> swp5 bridge FORWARDING
<E2><94><9C> swp6 bridge FORWARDING
<E2><94><9C> swp7 bridge FORWARDING
<E2><94><9C> swp8 bridge FORWARDING
<E2><94><9C> swp9 bridge FORWARDING
<E2><94><94> swp10 bridge FORWARDING
This is because the raw tty from klish disables IUTF8 and the fact that
it does not source any environment, e.g., /etc/profile. (We do not have
any locale settings in the enviornment either, but that's a discussion
for another day.)
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This reverts commit 0ee973b2b2.
Turns out that this workaround simply reduced the size of the window
where this issue can occur.
The previous change now ensures that the DSA tree is always fully
setup by the time nameif runs.
Before this change, we relied on `udevadm settle` to act as a barrier
which we could only cross after all devices had been probed. As it
turns out, when drivers defer probing due to missing dependencies,
`udevadm settle` may exit (as no events are generated for a period of
time) before all devices are set up. This was the root cause behind
issue #685, for which #752 was the initial attempt at a fix.
As we know that systems using mv88e6xxx will always have a device link
referencing the conduit interface, add a script to finit's system
runparts directory, which will block while any device link consumers
are still probing.
As a consequence of this, we can no longer rely on the sysklogd.conf
shipped with finit. Therefore, install an Infix specific one, which
will make sure that the aforementioned script has run before launching
the syslog daemon, which most other things depend on.
Fixes#685
- No more default writable layer
- Don't mention read-only (deprecated, and always on now)
- Use ghfm note highlights
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
