The mt7622 soc has a built-in wmac, same driver as the mt7615, but
it lacked MODULE_DEVICE_TABLE() so udev could not autoload driver
and firmware.
This commit also adds the wmac+bluetooth specific firmware.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add board support for the BananaPi BPI-R4 router board, based on the
MediaTek MT7988A (Filogic 880) SoC with quad-core Cortex-A73 CPU.
The BPI-R4 is the successor to the BPI-R3 but uses entirely different
silicon: the internal switch runs at 2.5 GbE per port, the two SFP+
uplinks use native USXGMII at up to 10 Gbps, and WiFi is provided by
a MediaTek MT7996E PCIe module supporting tri-band WiFi 7 (2.4/5/6 GHz).
Two board variants, BPI-R4-2g5 and BPI-R4P, replace one SFP+ cage with
a 2.5 GbE RJ45 port (using the MT7988A internal 2.5G PHY); the R4P adds
an optional PoE daughterboard on that port. Both use the upstream
mt7988a-bananapi-bpi-r4-2g5 device tree.
Interfaces:
- Standard R4: eth1 (gmac1/sfp2 LAN cage) → sfp2, eth2 (gmac2/sfp1 WAN cage) → sfp1
- R4-2g5/R4P: eth1 (2.5G PHY) → wan, eth2 (gmac2/sfp1 WAN cage) → sfp1
Factory reset / WPS button (GPIO14, active-low): detected by U-Boot at
boot for factory reset; reused by Linux as KEY_WPS_BUTTON at runtime.
eMMC install note: the MT7988A eMMC (pins 38-49) and SD card (pins 32-37)
use separate physical pads so there is no electrical bus sharing, unlike
some BPi-R3 configurations. However, a single MMC controller
(mmc@11230000) handles both, so only one is active per boot session.
The eMMC install procedure therefore still requires an intermediate SPI
NAND bootloader step until a Linux-side install path is tested.
SD card build (bpi_r4_sd_boot_defconfig) now uses the new
mt7988a_bpir4_sd U-Boot defconfig with cap-sd-highspeed enabled,
giving 50 MHz SD transfers instead of the previous 25 MHz legacy mode.
Also adds MT7988/MT7996 firmware support to the buildroot linux-firmware
package, for 2.5 GbE port PHY and WiFi7 extension board, and updates the
aarch64_defconfig, aarch64_minimal_defconfig, the arch README, CI
boot/image workflows, mkimage.sh, and the ChangeLog.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This fix the instability of the display on soft reboots,
previous it required a powercycle to get display to work properly
Add patches from rpi-linux, and a small fixup from me.
Signed-off-by: Mattias Walström <lazzer@gmail.com>
Add board support for the BananaPi BPi-R64 router board, based on the
MediaTek MT7622 SoC and MT7531 Gigabit Ethernet switch.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
In a hybrid MBR the conventional layout (used by gdisk and others) is:
MBR[0] = 0xEE (GPT protective, covers whole disk)
MBR[1..3] = user-selected GPT partitions with legacy type codes
genimage currently appends the 0xEE entry after the data partitions,
producing the opposite order. This is fine for most platforms, but
breaks firmware that detects GPT by inspecting only MBR entry 0: seeing
a non-0xEE type there it falls into pure-MBR mode and cannot look up
GPT partitions by name.
The TF-A partition driver (drivers/partition/partition.c) exhibits
exactly this behaviour: load_mbr_header() copies entry[0] and checks
type == 0xEE to select between MBR and GPT mode. The MediaTek MT7622
platform (BananaPi BPI-R64) is a concrete example where this matters.
On the other hand, Raspberry Pi firmware scans all MBR slots for a
bootable FAT32 partition. If slot 0 holds a 0xEE protective entry the
firmware switches to GPT detection, looks for an EFI System Partition
UUID, and reports "no bootable partitions" when none is found.
Add an opt-in hdimage option `gpt-protective-first = true` that places
the 0xEE entry at slot 0 and shifts data partitions to slots 1..3.
The default (false) preserves the existing genimage behaviour so that
platforms like Raspberry Pi continue to work without any changes.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
A legacy name length limit in firewalld triggered problems with longer
policy names. This patch to firewalld lifts that limit by checking the
backend in use, no limit for nftables.
Fixes#1389
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This includes adding a netd-daemon since FRR has gone towards all
daemons should be configured from mgmtd using YANG, netd uses gRPC to
reconfigure in mgmtd
Signed-off-by: Enable grpc
This is a simple two port router board, with the same
WiFi chips as BPI-r3.
The bootloader shall be the same as the BPI-r3, the bootloader
now probes which of the two is booting by checking for the PHYS
that only exist on BPI-r3-mini.
This patch enables umask and nacm defalts in the Buildoot sysrepo
package and a patch to sysrepo to set the sysrepo group also on the
event pipes in /etc/sysrepo/, without which it would be hard to inject
any type of new event as non-root user now since the umask now prevent
all 'other' users from interacting with sysrepo.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
ael-bot