With the new yangerd it failed 100% of the times, but it could fail
before as well, but that whould be very rare. Wait until operational
has been updated.
The test got an unexpected input in one of its logs:
'May 22 11:18:32 test-00-03-00 yangerd[3677]: SIGHUP: triggering immediate re-poll'
limit the string grepping for to be more exact.
Specially the change:
`
- oper = target.get_dict("/system-state/software")
+ oper = target.get_dict("/ietf-system:system-state/software")
`
i feel is strange, since only the backend for sysrepo has changed, but the
new syntax is actually correct, unsure why it has worked before.
Previously at least one end of a veth pair had to remain in the host
namespace, because that end created and destroyed the pair. Assigning
both ends to containers left no one to create it.
Select a deterministic primary end so exactly one side creates the pair.
When the primary is itself a container interface, create the pair in the
host namespace before the container starts; CNI host-device then moves
each end into its container. Teardown is deferred to the container
removal script so the pair does not linger and block re-creation.
Drop the now-obsolete limitation notes from the documentation and YANG,
and add a regression test connecting two containers over a veth pair.
Fixes: #941
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Refactor to use a dummy interface instead of wasting a dut. This not
only simplifies the test but also increases test coverage on test rigs
with a single DUT.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add conditional YANG feature 'web-ui' to infix-services.yang, set when
the webui is built. This feature is what the test now looks for to
determine if it should be skipped or not.
Also, clean up remnant of old test, which was entirely replaced by
Mattias' login/csrf test.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This commit increases attempts on checks in this particular test from default 10 to 60.
This has been introduced to match worst case scenario where after 3 retries(5s) each dhcp waits 30 seconds before next 3 retries.
Commits yields to much more stable test behaviour.
Resolves: #1515
Signed-off-by: Ejub Sabic <ejub1946@outlook.com>
Verify:
- Unauthenticated GET / -> 303 to /login
- Bad-password rejection -> no session is created
- Session cookie is flagged HttpOnly
- Authenticated GET /interfaces -> 200
- with htmx-config meta tag check
- State-changing POST without CSRF token -> 403
- POST with X-CSRF-Token header -> succeeds
- After logout the session no longer grants access
The cookie-preserving WebUI helper class also folds in the IPv6
link-local zone-id workaround (re-encode %25 back to %) that
infamy.restconf already uses.
Signed-off-by: Mattias Walström <lazzer@gmail.com>
This commit introduces xpath coverage test report. It plugs into transport layer of test system and generates .md report.
Commit also introduces "make xpath-coverage-report" used to generate pdf out of md.
Resolves: #581
Signed-off-by: Ejub Sabic <ejub1946@outlook.com>
- Include /run and /tmp in mount-points, likely more interesting than /.
- Include advertised link modes in operational to compare with supported
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The test-report target fed a pre-baked report.adoc to asciidoctor-pdf.
Let 9pm's report.py, the author of result.json, both generate and
render the report instead. It is invoked with Infix's own theme, fonts
and logo so the output is unchanged; downstream projects need only
override LOGO to rebrand it.
Signed-off-by: Richard Alpe <richard@bit42.se>
The Ethernet packet/RMON counters at the bottom of 'show interface
<name>' were appended with a wider label column than the operational
data above them, breaking visual alignment. Group them under an
"Ethernet Statistics" section heading (Decore.title), same convention
as 'Available Networks' in the wifi scan view.
Narrow the operational-data label column from 20 to 19 chars so the
title bar exactly matches the heading text — a tighter and more
deliberately aligned look. All labels in pr_iface fit within 19
chars except 'lacp system priority' (20); rename it to 'lacp sys
priority' for consistency with the other 'lacp ...' labels (lacp
aggregate id, lacp partner mac, ...) so the new field width works
universally.
Refresh CLI snapshots and doc samples to match.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Import ieee802-ethernet-interface@2025-09-10.yang, from IEEE 802.3.2-2025,
and companion ieee802-ethernet-phy-type.yang, replacing the 2019 revision.
Operational interface speed moves to ietf-interfaces:speed, RFC 8343,
eth:speed is now obsolete. Bump infix-interfaces.yang revision to track
the upgrade.
The CLI 'show interface' command renders interfaces as bottom-up layered
protocol rows. Ethernet interfaces a new IEEE link-mode row (1000baseT,
10GbaseLR, ...) is added with 'duplex: full|half' in the DATA column.
Without link the ethernet row is the first row. Tunnels and wifi follow
the same layering: gre/vxlan rows carry remote:/vni: tokens with optional
ethernet sub-row for the L2-bearing variants; wifi rows carry 'station' or
'access-point' ssid:, signal:, stations: tokens.
admin@bpi-76-8f-c2:/> show interface
⚑ INTERFACE PROTOCOL STATE DATA
⇅ lo loopback UP
ipv4 127.0.0.1/8 (static)
ipv6 ::1/128 (static)
⇅ br0 bridge DOWN
│ ethernet 32:2e:3f:76:8f:c2
│ ipv4 192.168.0.1/24 (static)
⇅ ├ lan0 bridge LOWER-DOWN
⇅ ├ lan1 bridge LOWER-DOWN
⇅ ├ lan2 bridge LOWER-DOWN
⇅ └ lan3 bridge LOWER-DOWN
⇅ gre0 gre UP remote: 198.51.100.7
ipv4 10.255.0.1/30 (static)
⇅ sfp1 ethernet DOWN ca:59:f0:77:80:5b
⇅ wan 1000baseT UP duplex: full
ethernet 32:2e:3f:76:8f:c2
ipv4 192.168.0.235/24 (dhcp)
ipv6 fe80::302e:3fff:fe76:8fc2/64 (link-layer)
⇅ wan.10 vlan UP vid: 10
│ ipv4 10.0.10.1/24 (static)
└ wan
⇅ wan.10.20 vlan UP vid: 20
│ ipv4 10.0.10.20/28 (static)
└ wan.10
⇅ wifi0 wifi UP station ssid: corp-net signal: good
ethernet dc:a6:32:00:11:22
ipv4 192.168.7.42/24 (dhcp)
yanger populates phy-type and pmd-type from a static ETHTOOL link-mode
identity table keyed on (port, speed, duplex). Both leaves are populated
for unambiguous media (copper, DAC, copper-T); for generic fiber where
the (port, speed, duplex) tuple can map to multiple PMDs (SR vs LR vs
ER, etc.) only the phy-type family identity is emitted — guessing the
PMD would be misleading. cli_pretty prefers pmd-type (specific) and
falls back to phy-type (family) for display.
yanger also emits ietf-interfaces:speed and fixes a long-standing
'auto-negotation' typo (yanger had never matched ethtool's correctly-
spelled JSON field, so operational auto-negotiation always read
'unknown').
Filling the WG's gap on fixed-speed config
------------------------------------------
IEEE Std 802.3.2-2025 obsoleted the eth:speed leaf without providing a
config-true replacement; the standards-correct way to express what
older Infix configurations called 'fixed speed' is to restrict the set
of PMDs auto-negotiation may advertise. Augment auto-negotiation with
two leaf-lists:
auto-negotiation/advertised-pmd-types config-true, leaf-list of pmd-type
ethernet/supported-pmd-types config-false, leaf-list of pmd-type
Pinning a port to a single mode is now expressed as a single-entry
advertised-pmd-types list. The kernel-supported set is exposed as
operational state for diagnosis — SFP/SFP+ cages report the inserted
module's capabilities, narrowing the list to a single PMD when the
optic only supports one mode (as suggested by @wkz in PR review).
When the supported list collapses to a single entry, yanger uses it
to refine the operational pmd-type leaf — more accurate than the
(port, speed, duplex) lookup for fiber.
confd C apply path (src/confd/src/ieee802-ethernet-interface.c)
translates each advertised pmd-type identity to the corresponding
ETHTOOL_LINK_MODE_*_BIT_*, ORs them into a mask, and emits
'ethtool --change <if> autoneg on advertise 0x<mask>'. An empty
list keeps the historical default of advertising every supported
mode. The (legacy) 'auto-negotiation/enable = false' + speed/duplex
branch is removed — it has no model representation any more.
cli_pretty's detail view gains 'advertised' and 'supported' rows
listing the PMDs in each set. A new _pr_label_list() helper unifies
multi-row rendering across these new rows and the pre-existing
ipv4/ipv6 address rows.
The detailed interface view also gains a 'link mode' row carrying the
pmd-type / phy-type-derived label.
Migration of existing startup configurations
--------------------------------------------
Bump confd version 1.8 → 1.9 to trigger the migration on upgrade.
share/migrate/1.9/10-ethernet-advertise.sh translates old configs of
the form
ethernet { auto-negotiation { enable false; } speed S; duplex D; }
into
ethernet { auto-negotiation { advertised-pmd-types [PMD]; } duplex D; }
mapping (S, D) → PMD via a static lookup covering the copper-T speeds
the deprecated speed leaf historically supported (10/100/1000/2.5G/
5G/10G). Interfaces that don't disable auto-negotiation, or that
lack a speed leaf, are passed through untouched.
Closes#530Closes#805
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Mattias Walström