Classic builds don't have udev but rather mdev or mdevd. This patch
imports support from myLinux for conditionally starting sysklogd on
classiic builds.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Since watchdogd may need to run with SCHED_RR, when the supervisor is enabled,
which is not supported by cgroupsv2, we ask Finit to always runs it in the
root cgroup. We must also raise the limit for rtprio to all possible values
for SCHED_RR that a user can set in /etc/watchdogd.conf
Finally, add support for reading extra args from /etc/default/watchdogd
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
A very limited part of the YANG model is implemented so far, basicly it is OSPFv2 with multiple areas and you can change timers
for the interfaces. Limited operational support.
admin@infix-00-00-00:/config/> edit routing control-plane-protocol ietf-ospf:ospfv2 name default
admin@infix-00-00-00:/config/routing/control-plane-protocol/ietf-ospf:ospfv2/name/default/> set ospf area 0.0.0.0 interface e0 enabled true
admin@infix-00-00-00:/config/routing/control-plane-protocol/ietf-ospf:ospfv2/name/default/> leave
Normally, no logins are actually possible, but this will have two
desirable effects effects:
- /etc/issue will be printed when hitting return over the console,
allowing the user to see the bootstrapping errors again, without
having to reboot the system.
- On devleoper builds, with CONFIG_TARGET_ENABLE_ROOT_LOGIN, we can
login as root and debug issues.
When Infix Fail Secure Mode ends up in RMA state, runlevel 9, we should
not allow Finit to "time out" and give us a login prompt. Instead we
disable all login services in runlevels 7-9, reserving these extra
levels for future failure modes.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The sysklogd and BusyBox syslogd can not run at the same time. Since they
provide the same service we standardize on them providing <pid/syslogd>.
Also, ensure syslogd does not start until the fifth udevadm has completed.
This creates a barrier preventing other run/task/services from starting
too early. Thus guaranteeing a proper boot order.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Instead, use the version from package/skeleton-init-finit, including the
ssh-hostkeys (previously ssh-genhostkeys) from the same package, because
it include extensive error handling and logging on failure.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This change addresses a problem accessing Infix over SSH. The root cause
turned out to be the hostkeys, which live in /var/lib/ssh and not in /etc
on Infix, were corrupt.
The corruption was interesting in that they all existed, but had size 0.
This state was not caught by our ssh-genhostkeys script and that is what
this change attempts to fix.
As before this change, the script starts by calling `sshd -t` to verify
they hostkeys. Unlike before we now check for 'invalid format' in the
output of that command. If any file with invalid format is found, we
remove them and regenerate the hostkeys.
In this investigation it was found that the 'ssh-keygen -A' command that
generates hostkeys does not use the directories specified for the given
files in sshd_config, instead it always saves the files to /etc/ssh.
Also, since there is no panic in getting the hostkeys generated we can
allow the script to wait for syslogd to start before we run, even though
it all happens in runlevel S.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Also, for usability, add `name:<SVC>` to each service declaration so they
can be located more easily and/or enabled/disabled using the service they
provide.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This patch drops auto-enable of services we want to be able to control
via NETCONF/YANG. SSDP and mDNS/SD enable/disable configure support,
using native models, will be included in the same PR and LLDP+SNMP may
come later, using std. IEEE/IETF models, they are not critical atm.
Fix#118
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- allow custom options sourced from optional /etc/default/smcrouted
- don't enable smcrouted by default when enabled in Buildroot .config
because normal use-cases require an /etc/smcroute.conf
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
When calling `make foo-rebuild` one expects all the registered hooks in
the foo package to have been called by Buildroot. The Buildroot manual
has this to say about the target-finalize hook:
> These hooks are run after all packages are built, but
> before the filesystem images are generated. They are
> seldom used, and your package probably do not need them.
The correct hook to use for target packages is POST_INSTALL_TARGET_HOOK.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Without --force-bind, the address is removed if another routable
address is added to the interface.
While this is likely something that should be configurable in the
future, we choose this mode as the default so that IPs used for
NETCONF connections are not dropped because other addresses are added.
Some critical services must never be stopped, and with the unfortunate
separation of runlevel S and 0 in Finit recently, all affected service
definitions must be updated.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- board/common: drop everything not needed by NETCONF mode
- board/classic: most board/common helpers relocated here
- Simplify Finit scripts for critical services
- Source variant from /etc/os-release to select ramdisk /etc
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
With the new templating support in Finit, and this patch, we can now
very easily enable a ZeroConf service on, e.g., eth0:
$ initctl enable zeroconf@eth0
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
When calling 'make skeleton-init-finit-rebuild' to (re)install any new
or modified services, we cannot remove everything installed already.
That breaks what other packages may have installed already and is not
the Buildroot way.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This commit adds multi-nameserver support using openresolv (resolvconf)
and dnsmasq. This means that a DHCP client (dhcpcd) or VPN client can
be providers of nameservers to the system. Dnsmasq takes over as the
system resolver, except when the user has set up static configuration.
Static nameserver(s), as well as search and options, are always added
first by openresolv to /etc/resolv.conf.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Chrony drops privs after startup to user chrony, when restarting it
writes its state in /var/lib/chrony, so the directory needs to have
the correct permissions for that user.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
With the recent `if:<cond>` addition to Finit we can simplify a lot of
the logic for disabling and enabling features in Infix. Standardizing
on conditions that Finit provides.
We create boot/netconf, boot/etc, and boot/profinet conditions early,
after all filesystems have been mounted (and cleaned), so they are all
set before Finit loads its configuration files in runlevel S.
The default is still to boot into a managed NETCONF mode, since the end
goal remains to integrate PROFINET as yet another service. The other
mode, native /etc, should then be the only exception.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Split tmpfiles config in two, one for snmpd and one for profeth.
Add logging and redirect profeth logs to /log/profinet.log with
default log rotation.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
An Infix build with PROFINET gears Net-SNMP heavily towards acting as a
servant to profeth (p-net stack). This will be hard-coded for now until
we've integrated it all better in Clixon.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
On rebuild (without distclean) the getty.conf contained two tty lines
for the same TTY, causing Finit to believe the command line args had
been changed between each reload -- and thus kicking out the logged
in console user who just typed `initctl reload`.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Need to rsync the whole skeleton since we provide more than just the
finit.d files, e.g. /etc/fstab, which we also modify in this .mk.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
1. Use same naming standard for quagga and frr
2. Only one of quagga and frr can be used at the same time
3. Subdirectories in available/ only in the skeleton, not on target
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Only install the corresponding Finit svc if the package is selected in
the Buildroot menuconfig. Some packages cannot be enabled by default
though, since they require a daemon configuration file, e.g. in the
case of ulogd it requires a valid /etc/ulogd.conf
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Also needs /var/cache/nginx when starting up. Requires separate patch
for now, but will be added a tmpflies.so plugn to Finit.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The whole of /var may be read-only, while /run is a newstyle ramdisk.
The /run/lock directory is created by the Finit bootmisc.so plugin at
boot.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
