Previously the sys-cli group was for interactive shell access, but with
ever changing requirements this split has become necessary.
This commit introduces the 'sysrepo' group for low-level access to all
sysrepo commands, i.e., bootstrap only. For user-level shell access a
'klish' group is added which allows users to connect to the CLI. This
is now the only group users, including the default 'admin', are members
of, effectively making the new 'copy' tool the norm.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Replace BusyBox udhcpc6 with OpenWrt's odhcp6c for improved DHCPv6
functionality and better integration with Router Advertisements (RA).
The primary motivation is support for a common ISP deployment scenario
where IPv6 addresses are assigned via SLAAC (from Router Advertisements)
and DHCPv6 is used in stateless/information-only mode to provide DNS
servers and other configuration options. This hybrid RA+DHCPv6 setup is
standard practice for many ISPs but was not supported by udhcpc6, which
treats RA and DHCPv6 as separate, non-integrated mechanisms.
Additional benefits of odhcp6c:
- Better IPv6 Prefix Delegation (IA-PD) support with proper handling
of delegated prefix lifetimes and renewal
- Native integration of RA-provided configuration (DNS servers, routes,
addresses) with DHCPv6-provided options
- Support for stateless DHCPv6 via information-only mode
To verify stateless DHCPv6 integration with SLAAC addresses - the ISP
scenario that motivated this migration, a new test case has been added.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Almost full support for WireGuard
admin@server:/> show interface wg0
name : wg0
type : wireguard
index : 10
mtu : 1420
operational status : up
ipv4 addresses : 10.0.0.1/24 (static)
ipv6 addresses : fd00::1/64 (static)
peers : 2
Peer 1:
public key : ROaZyvJc5DzA2XUAAeTj2YlwDsy2w0lr3t+rWj2imAk=
status : UP
endpoint : 192.168.10.2:51821
latest handshake : 2025-12-09T22:51:38+00:00
transfer tx : 1412 bytes
transfer rx : 1324 bytes
Peer 2:
public key : Om9CPLYdK3l93GauKrq5WXo/gbcD+1CeqFpobRLLkB4=
status : UP
endpoint : 2001:db8:3c4d:20::2:51822
latest handshake : 2025-12-09T22:51:38+00:00
transfer tx : 1812 bytes
transfer rx : 428 bytes
in-octets : 1752
out-octets : 3224
admin@server:/>
After merging post-post-image, TRUSTED_KEYS must be set in order for
the keys to be injected into the U-Boot DTB, so we need to explicitly
enable it for all boards that use the generic secure boot scripts.
This was a stray config fragment used during development that was
accedentally included in the referenced commit.
Fixes: 0fe5964909 ("aarch64_qemu_boot: Restore build after removing post-image.sh")
Add a generic image target to build aux.ext4, which can be used both
when creating target-specific SD-card images, and when creating
regular disk images.
While we're here, make sure that we don't need a RAUC bundle in order
to generate aux.ext4 (which mkrauc-status.sh did). This saves us time
on _every_ incremental build.
Used in Marvell Armada SOCs like the 37xx, 7k, 8k, and CN913x series.
Fixes the following kernel warnings:
[ 16.074759] crypto-safexcel f2800000.crypto: Firmware load failed.
[ 16.087330] crypto-safexcel f2800000.crypto: HW init failed (-2)
[ 16.102696] crypto-safexcel f2800000.crypto: probe with driver crypto-safexcel failed with error -2
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This commit adds support to simplify sdcard.img generation by downloading the
latest bootloader build for a board from the 'latest-boot' release tag. The
tarball is saved in dl/bootloader/ and is extracted to a temporary directory
in output/build/boot-$board-xxxx on every invocation of mkimage.sh. This is
used for invoking genimage and bmaptool before copying the resulting images
to output/images/. (If $O is set, it is used instead of output/, above).
New options:
-d Download latest bootloader build for the given board
-f Force re-download even if bootlaoder tarball existgs
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Update board paths to match the restructuring in commit ab56c1be.
Fixes rpi4, cn9130_crb, and aarch64_qemu bootloader builds.
[skip ci]
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This commit consolidates mkimage.sh scripts into a unified SD card image
creation tool that works for all boards. It needs a bootloader an $ARCH
rootfs.squashfs image and a genimage.cfg.in template.
- Detects build directories from `O=` environment variable or `output/`
- Sources `.config` to discover Buildroot paths
- Uses Buildroot's `support/scripts/genimage.sh` when available
- Automatically generates `.bmap` files if `bmaptool` is available
- Fallback to direct `genimage` invocation if wrapper not found
See the online instructions for usage.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This commit drops the board specific defconfig in favor of proper BSP
support for the FriendlyARM NanoPi R2S to Infix as part of the default
Aarch64 build.
The name FriendlyARM was elected over FriendlyELEC ("new" name) to be
consistent with both kernel and Buildroot naming standards.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This commit consolidates all BSP support files into the Buildroot standard
board/ directory. The concept of selectable boards in menuconfig remains
as-is but now lives in board/ instead.
Drop support for board-specific post-build.sh scripts, not needed atm. and
we should really use Buildroot _POST_INSTALL_HOOKS in the board .mk files
instead.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
With the additional support for RPi3, including Zero 2W, this commit renames
all relevant directories and Config.In options to match.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This commit adds support for the Raspberry Pi CM4 based mini DFRobot IoT
Router board, SKU:DFR0767. It comes with an additional RTL8111 PCIe NIC
hence the addidtional kernel module and firmware. The latter fixes:
r8169 0000:01:00.0: Direct firmware load for rtl_nic/rtl8168h-2.fw failed with error -2
r8169 0000:01:00.0: Unable to load firmware rtl_nic/rtl8168h-2.fw (-2)
Please note, the change in BCMGENET from module to built-in is to ensure
it is probed before any PCIe NIC, both this board and the CM4-based NVME
NAS base board enumerate the built-in MAC as eth0.
Also, unlike the RPi 3B/4B, it is not a given fact that a CM4 based board
comes with WiFi onboard, and since most compute module setups are DYI, we
take the easy way out and leave it as an exercise to the user to add WiFi
interface to the config.
https://wiki.dfrobot.com/Compute_Module_4_IoT_Router_Board_Mini_SKU_DFR0767
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The BCM2837 core is used not just in the RPi 3B but also in the Zero 2W,
both device trees have been added to the board config.
The BCM2711 support has been extended to include RPi 400 and CM4 I/O.
To support the BCM2837 family more firmware options habe been enabled,
since the RPi3 does not have bootcode.bin flashed in the SoC. The SD
card image now uses a hybrid GPT/MBR format so the RPi3 bootcode.bin
can read all files from the first VFAT partition.
The default device tree for Linux is now chosen by the U-Boot probe and
the only exception is the "laundry room" detector that looks for a RPi4
with a 7" touch screen, which then selects the DSI enabled RPi4 variant.
This is enough to properly load an RPi 3B and a CM4 based router board.
The BCM2837 does not have PCI/PCIe or a built-in MAC so it relies on the
USB to Ethernet LAN78xx which does not support disabling pause frames.
I have opted for checking for EOPNOTSUPP instead of adding yet another
quirk, because it is likely to be a common limitation of more drivers
and chipsets, and this code is best-effort anyway.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add supoprt for infix-firewall.yang, modeled on the zone-based firewalld
The terminology is a mix of firewalld, classic netfilter and inspired by
Ubiquity. E.g., zone 'policy' -> 'action', and the zone matrix overview.
- Port forwarding allows forwarding a range of ports
- Operational data comes from firewalld active rules
- Firewall logging goes to /var/log/firewall.log
- Show implicit/built-in rules and zones (HOST) in firewall matrix,
includes "locked" policy for the default-drop behavior
- The zone services field in admin-exec 'show firewall' shows ANY when
the zone default action is set to 'accept'
- Zone 'forwarding' and 'masquerade' settings live in Infix in the
policys instead, meaning users need to explicitly add a policy
to allow both intra-zone and inter-zone forwarding
- Support for emergency lockdown (kill switch)
- Pre-defined services (xml+enums) are filtered and included as a
separate YANG model, extensions added for netconf and restconf
- Includes initial support for firewalld rich rules
firewalld policy rules, including rich rules, have an obnoxious priority
field which is extremely hard to get right, so in Infix we use the far
superior YANG construct 'ordered-by user;'. This ensure all rules are
generated in that order by setting the priority field, on read-back from
firewalld (operational) the priority field is used to sort the output
of rules in the CLI.
Fixes#448
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The Banana Pi R3 is a high-performance networking board featuring:
- MediaTek MT7986 ARM Cortex-A53 quad-core processor
- 4x Gigabit LAN ports (lan1-lan4)
- 1x Gigabit WAN port
- 2x SFP ports (sfp1, sfp2) for fiber connectivity
- Dual WiFi interfaces (wifi0 for 2.4GHz, wifi1 for 5GHz)
- USB support
- SD card boot support
Joachim Wiberg