The wi-fi architecture in infix require udev to run and remove the kernel automatic wlan-interface
this. Unclear reason, but it seems that udev sometimes miss the add event.
Verified with latest Finit 4.15 that reboot after resize works.
Added a comment to the board-specific .mk file about the broken
WDT on the RK3328 SoC, or rather the NanoPi R2S board.
Fixes#1292
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Board probing cannot copy board specific files to /usr (read-only), so
let's share this script with all other aarch64 boards.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Almost full support for WireGuard
admin@server:/> show interface wg0
name : wg0
type : wireguard
index : 10
mtu : 1420
operational status : up
ipv4 addresses : 10.0.0.1/24 (static)
ipv6 addresses : fd00::1/64 (static)
peers : 2
Peer 1:
public key : ROaZyvJc5DzA2XUAAeTj2YlwDsy2w0lr3t+rWj2imAk=
status : UP
endpoint : 192.168.10.2:51821
latest handshake : 2025-12-09T22:51:38+00:00
transfer tx : 1412 bytes
transfer rx : 1324 bytes
Peer 2:
public key : Om9CPLYdK3l93GauKrq5WXo/gbcD+1CeqFpobRLLkB4=
status : UP
endpoint : 2001:db8:3c4d:20::2:51822
latest handshake : 2025-12-09T22:51:38+00:00
transfer tx : 1812 bytes
transfer rx : 428 bytes
in-octets : 1752
out-octets : 3224
admin@server:/>
Actually disable iitod on Styx DCP-SC-28p to work around #670, this
prohibits software control of LEDs, leaving the default HW control,
which has proven more stable on this platform.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
We previously run a draft version of a lot of YANG models,
netconf-server,ssh-server and mode. Now they are released
with minor changes.
infix-meta is an exception, here we had to remove the obsolete
marker of the node and value, since this is no longer allowed in
libyang.
On platforms based on CN913{0,1,2}, collect all ECC related counters
so that we know if any correctable errors have been encountered since
the most recent boot.
Rev. A has a FLASH that Linux reconfigures to 4B-addressing, but must
be in 3B-addressing when accessed by the BootROM. Since it has no
reset input, this would not work on warm resets. Linux has a
workaround for this issue for the common case of a controlled reboot,
which this change enables on those boards (which are admittedly few
and far between, but still useful as testing vehicles).
(This won't take effect until Finit is updated to at least 4.15, which
switches over from watchdog- to reboot(2)- based reboot, by default)
Turn on OOPS-to-panic, soft/hard lockup panic, hung-task panic, and
extra workqueue watchdog reporting. This makes latent stalls visible
instead of silently freezing, improving diagnosis of issues like the
recent resource-pressure lockup.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
We have not installed .dtb:s to $O/images/ for quite some time, and
nobody cared. That goes to show that this is not really used.
The image is still useful at times, so if it needed in the future,
then we can resurrect it from the logs and refactor it to an image
package.
The board/*/*/*.mk is very broad, intended to hit all board specific
definitions, but may also cause duplicate inclusions, e.g., in
board/common.
Let each architecture do the inclusion instead.
- firewall: allow traffic to be forwarded from lan to wan zone
- dhcpv6: enable client on wan interface
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Now that we've got everything working, it's just annoying, so disable it
but leave it in with a comment.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Devices should tell the server what they are in case an administrator
wants to group or hand out dedicated leases and information to some
devices on the lan.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Please note, this change drops not only the global enabled flag, but also the
per-interface enabled flag, converting it to a presence container. The name
of the container is also shortened from dhcp-client -> dhcp. A pattern that
expected to be reused also for the DHCPv6 client.
Fixes#1109
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Reduce /var image size to 128M (resized at first boot anyway) and tune
mke2fs options for faster mounting. Set ext4 'uninit_bg' feature and
use '-m 0 -i 4096' extraargs in genimage to optimize filesystem creation
and reduce overhead. The genimage tool has several tweaks enabled by
default already, the 'uninit_bg' feature speeds up the time to check
the file system.
Disable periodic fsck with tune2fs at boot while keeping safety checks
intact. Adjust mount options in fstab to reduce journal syncs and
improve boot time.
Fix severe performance regression in find_partition_by_label() that was
calling sgdisk on every block device including virtual devices (ram, loop,
dm-mapper). This caused boot delays of up to 24 seconds on systems with
many block devices. Now skip virtual devices that don't have GPT tables,
reducing the delay to ~2 seconds.
Also clean up is_mmc() function to use cached result.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This commit consolidates mkimage.sh scripts into a unified SD card image
creation tool that works for all boards. It needs a bootloader an $ARCH
rootfs.squashfs image and a genimage.cfg.in template.
- Detects build directories from `O=` environment variable or `output/`
- Sources `.config` to discover Buildroot paths
- Uses Buildroot's `support/scripts/genimage.sh` when available
- Automatically generates `.bmap` files if `bmaptool` is available
- Fallback to direct `genimage` invocation if wrapper not found
See the online instructions for usage.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Add new interface quirk to allow skipping disabling of flow control on
all RPi 3B/4B devices that have the smsc95xx driver.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The xPi's usually don't have a VPD so the chassis mac-address probed at
boot is usually null in /run/system.json. This commit adds a fallbkack
mechanism to populate this field so it can be used for unique hostnames
even on these boards.
Ths ietf-hardware.yang model does not have a notion of physical address,
so we augment one tht is generic enought to be used for other hardware
components than Ethernet, similar to what ietf-interfaces.yang use.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
- Enable bridging of LAN ports in br0, default IP: 192.168.0.1/24
- Enable firewall with two zones: 'wan' and 'lan', policy: lan-to-wan
- Enable DHCP server on br0
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This commit drops the board specific defconfig in favor of proper BSP
support for the FriendlyARM NanoPi R2S to Infix as part of the default
Aarch64 build.
The name FriendlyARM was elected over FriendlyELEC ("new" name) to be
consistent with both kernel and Buildroot naming standards.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This commit consolidates all BSP support files into the Buildroot standard
board/ directory. The concept of selectable boards in menuconfig remains
as-is but now lives in board/ instead.
Drop support for board-specific post-build.sh scripts, not needed atm. and
we should really use Buildroot _POST_INSTALL_HOOKS in the board .mk files
instead.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
With the additional support for RPi3, including Zero 2W, this commit renames
all relevant directories and Config.In options to match.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
The DWC2 controller is a very common IP block in ARM and RiscV SoCs. With the
USB subsystem back to a built-in we can now enable host mode for the DWC2 (USB
2.0) ports on RPi. It also opens up for merging the NanoPi R2S into the
generic aarch64 build.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Use kernel cmdline option 'usbcore.authorized_default=2' to lock all
external/user-visible USB ports by default.
The kernel distinguishes internal vs external USB ports using ACPI
methods (_UPC and _PLD) on x86/x86_64 systems. On ACPI systems, ports
marked as non-visible but connectable are considered internal (e.g.,
hard-wired USB-to-Ethernet adapters) and are automatically authorized,
while user-visible external ports require manual authorization.
However, on device tree systems the kernel lacks a standard mechanism
for identifying internal ports. The 'authorized_default=2' setting falls
back to requiring authorization for all devices on these platforms,
We list user-accessible USB ports in the device tree ('usb-ports' and
'usb-port-names'), with unlisted ports being implicitly internal and
managed separately.
Fixes#1065
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Mattias Walström